diff -Nur ethercat-1.4.0/devices/e1000/Makefile.am ethercat-1.4.0.patched//devices/e1000/Makefile.am --- ethercat-1.4.0/devices/e1000/Makefile.am 2008-12-29 15:10:27.000000000 +0100 +++ ethercat-1.4.0.patched//devices/e1000/Makefile.am 2011-11-18 16:02:40.582568006 +0100 @@ -37,6 +37,8 @@ e1000-2.6.22-orig.h \ e1000-2.6.24-ethercat.h \ e1000-2.6.24-orig.h \ + e1000-2.6.32-ethercat.h \ + e1000-2.6.32-orig.h \ e1000_ethtool-2.6.13-ethercat.c \ e1000_ethtool-2.6.13-orig.c \ e1000_ethtool-2.6.18-ethercat.c \ @@ -47,6 +49,8 @@ e1000_ethtool-2.6.22-orig.c \ e1000_ethtool-2.6.24-ethercat.c \ e1000_ethtool-2.6.24-orig.c \ + e1000_ethtool-2.6.32-ethercat.c \ + e1000_ethtool-2.6.32-orig.c \ e1000_hw-2.6.13-ethercat.c \ e1000_hw-2.6.13-ethercat.h \ e1000_hw-2.6.13-orig.c \ @@ -67,6 +71,8 @@ e1000_hw-2.6.24-ethercat.h \ e1000_hw-2.6.24-orig.c \ e1000_hw-2.6.24-orig.h \ + e1000_hw-2.6.32-orig.c \ + e1000_hw-2.6.32-orig.h \ e1000_main-2.6.13-ethercat.c \ e1000_main-2.6.13-orig.c \ e1000_main-2.6.18-ethercat.c \ @@ -77,6 +83,8 @@ e1000_main-2.6.22-orig.c \ e1000_main-2.6.24-ethercat.c \ e1000_main-2.6.24-orig.c \ + e1000_main-2.6.32-ethercat.c \ + e1000_main-2.6.32-orig.c \ e1000_osdep-2.6.13-ethercat.h \ e1000_osdep-2.6.13-orig.h \ e1000_osdep-2.6.18-ethercat.h \ @@ -87,6 +95,8 @@ e1000_osdep-2.6.22-orig.h \ e1000_osdep-2.6.24-ethercat.h \ e1000_osdep-2.6.24-orig.h \ + e1000_osdep-2.6.32-ethercat.h \ + e1000_osdep-2.6.32-orig.h \ e1000_param-2.6.13-ethercat.c \ e1000_param-2.6.13-orig.c \ e1000_param-2.6.18-ethercat.c \ @@ -96,7 +106,9 @@ e1000_param-2.6.22-ethercat.c \ e1000_param-2.6.22-orig.c \ e1000_param-2.6.24-ethercat.c \ - e1000_param-2.6.24-orig.c + e1000_param-2.6.24-orig.c \ + e1000_param-2.6.32-ethercat.c \ + e1000_param-2.6.32-orig.c BUILT_SOURCES = \ Kbuild diff -Nur ethercat-1.4.0/devices/e1000/Makefile.in ethercat-1.4.0.patched//devices/e1000/Makefile.in --- ethercat-1.4.0/devices/e1000/Makefile.in 2008-12-29 17:01:14.000000000 +0100 +++ ethercat-1.4.0.patched//devices/e1000/Makefile.in 2011-11-18 16:02:49.202568094 +0100 @@ -179,6 +179,8 @@ e1000-2.6.22-orig.h \ e1000-2.6.24-ethercat.h \ e1000-2.6.24-orig.h \ + e1000-2.6.32-ethercat.h \ + e1000-2.6.32-orig.h \ e1000_ethtool-2.6.13-ethercat.c \ e1000_ethtool-2.6.13-orig.c \ e1000_ethtool-2.6.18-ethercat.c \ @@ -189,6 +191,8 @@ e1000_ethtool-2.6.22-orig.c \ e1000_ethtool-2.6.24-ethercat.c \ e1000_ethtool-2.6.24-orig.c \ + e1000_ethtool-2.6.32-ethercat.c \ + e1000_ethtool-2.6.32-orig.c \ e1000_hw-2.6.13-ethercat.c \ e1000_hw-2.6.13-ethercat.h \ e1000_hw-2.6.13-orig.c \ @@ -209,6 +213,10 @@ e1000_hw-2.6.24-ethercat.h \ e1000_hw-2.6.24-orig.c \ e1000_hw-2.6.24-orig.h \ + e1000_hw-2.6.32-ethercat.c \ + e1000_hw-2.6.32-ethercat.h \ + e1000_hw-2.6.32-orig.c \ + e1000_hw-2.6.32-orig.h \ e1000_main-2.6.13-ethercat.c \ e1000_main-2.6.13-orig.c \ e1000_main-2.6.18-ethercat.c \ @@ -219,6 +227,8 @@ e1000_main-2.6.22-orig.c \ e1000_main-2.6.24-ethercat.c \ e1000_main-2.6.24-orig.c \ + e1000_main-2.6.32-ethercat.c \ + e1000_main-2.6.32-orig.c \ e1000_osdep-2.6.13-ethercat.h \ e1000_osdep-2.6.13-orig.h \ e1000_osdep-2.6.18-ethercat.h \ @@ -229,6 +239,8 @@ e1000_osdep-2.6.22-orig.h \ e1000_osdep-2.6.24-ethercat.h \ e1000_osdep-2.6.24-orig.h \ + e1000_osdep-2.6.32-ethercat.h \ + e1000_osdep-2.6.32-orig.h \ e1000_param-2.6.13-ethercat.c \ e1000_param-2.6.13-orig.c \ e1000_param-2.6.18-ethercat.c \ @@ -238,7 +250,9 @@ e1000_param-2.6.22-ethercat.c \ e1000_param-2.6.22-orig.c \ e1000_param-2.6.24-ethercat.c \ - e1000_param-2.6.24-orig.c + e1000_param-2.6.24-orig.c \ + e1000_param-2.6.32-ethercat.c \ + e1000_param-2.6.32-orig.c BUILT_SOURCES = \ Kbuild diff -Nur ethercat-1.4.0/devices/e1000/e1000-2.6.32-ethercat.h ethercat-1.4.0.patched//devices/e1000/e1000-2.6.32-ethercat.h --- ethercat-1.4.0/devices/e1000/e1000-2.6.32-ethercat.h 1970-01-01 01:00:00.000000000 +0100 +++ ethercat-1.4.0.patched//devices/e1000/e1000-2.6.32-ethercat.h 2011-11-18 14:48:03.186942739 +0100 @@ -0,0 +1,367 @@ +/******************************************************************************* + + Intel PRO/1000 Linux driver + Copyright(c) 1999 - 2006 Intel Corporation. + + This program is free software; you can redistribute it and/or modify it + under the terms and conditions of the GNU General Public License, + version 2, as published by the Free Software Foundation. + + This program is distributed in the hope it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., + 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. + + The full GNU General Public License is included in this distribution in + the file called "COPYING". + + Contact Information: + Linux NICS + e1000-devel Mailing List + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + +*******************************************************************************/ + + +/* Linux PRO/1000 Ethernet Driver main header file */ + +#ifndef _E1000_H_ +#define _E1000_H_ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "../ecdev.h" + + +#define BAR_0 0 +#define BAR_1 1 +#define BAR_5 5 + +#define INTEL_E1000_ETHERNET_DEVICE(device_id) {\ + PCI_DEVICE(PCI_VENDOR_ID_INTEL, device_id)} + +struct e1000_adapter; + +#include "e1000_hw-2.6.32-ethercat.h" + +#ifdef DBG +#define E1000_DBG(args...) printk(KERN_DEBUG "ec_e1000: " args) +#else +#define E1000_DBG(args...) +#endif + +#define E1000_ERR(args...) printk(KERN_ERR "ec_e1000: " args) + +#define PFX "ec_e1000: " +#define DPRINTK(nlevel, klevel, fmt, args...) \ + (void)((NETIF_MSG_##nlevel & adapter->msg_enable) && \ + printk(KERN_##klevel PFX "%s: %s: " fmt, adapter->netdev->name, \ + __FUNCTION__ , ## args)) + +#define E1000_MAX_INTR 10 + +/* TX/RX descriptor defines */ +#define E1000_DEFAULT_TXD 256 +#define E1000_MAX_TXD 256 +#define E1000_MIN_TXD 80 +#define E1000_MAX_82544_TXD 4096 + +#define E1000_DEFAULT_RXD 256 +#define E1000_MAX_RXD 256 +#define E1000_MIN_RXD 80 +#define E1000_MAX_82544_RXD 4096 + +/* this is the size past which hardware will drop packets when setting LPE=0 */ +#define MAXIMUM_ETHERNET_VLAN_SIZE 1522 + +/* Supported Rx Buffer Sizes */ +#define E1000_RXBUFFER_128 128 /* Used for packet split */ +#define E1000_RXBUFFER_256 256 /* Used for packet split */ +#define E1000_RXBUFFER_512 512 +#define E1000_RXBUFFER_1024 1024 +#define E1000_RXBUFFER_2048 2048 +#define E1000_RXBUFFER_4096 4096 +#define E1000_RXBUFFER_8192 8192 +#define E1000_RXBUFFER_16384 16384 + +/* SmartSpeed delimiters */ +#define E1000_SMARTSPEED_DOWNSHIFT 3 +#define E1000_SMARTSPEED_MAX 15 + +/* Packet Buffer allocations */ +#define E1000_PBA_BYTES_SHIFT 0xA +#define E1000_TX_HEAD_ADDR_SHIFT 7 +#define E1000_PBA_TX_MASK 0xFFFF0000 + +/* Flow Control Watermarks */ +#define E1000_FC_HIGH_DIFF 0x1638 /* High: 5688 bytes below Rx FIFO size */ +#define E1000_FC_LOW_DIFF 0x1640 /* Low: 5696 bytes below Rx FIFO size */ + +#define E1000_FC_PAUSE_TIME 0x0680 /* 858 usec */ + +/* How many Tx Descriptors do we need to call netif_wake_queue ? */ +#define E1000_TX_QUEUE_WAKE 16 +/* How many Rx Buffers do we bundle into one write to the hardware ? */ +#define E1000_RX_BUFFER_WRITE 16 /* Must be power of 2 */ + +#define AUTO_ALL_MODES 0 +#define E1000_EEPROM_82544_APM 0x0004 +#define E1000_EEPROM_ICH8_APME 0x0004 +#define E1000_EEPROM_APME 0x0400 + +#ifndef E1000_MASTER_SLAVE +/* Switch to override PHY master/slave setting */ +#define E1000_MASTER_SLAVE e1000_ms_hw_default +#endif + +#define E1000_MNG_VLAN_NONE -1 +/* Number of packet split data buffers (not including the header buffer) */ +#define PS_PAGE_BUFFERS MAX_PS_BUFFERS-1 + +/* wrapper around a pointer to a socket buffer, + * so a DMA handle can be stored along with the buffer */ +struct e1000_buffer { + struct sk_buff *skb; + dma_addr_t dma; + unsigned long time_stamp; + uint16_t length; + uint16_t next_to_watch; +}; + + +struct e1000_ps_page { struct page *ps_page[PS_PAGE_BUFFERS]; }; +struct e1000_ps_page_dma { uint64_t ps_page_dma[PS_PAGE_BUFFERS]; }; + +struct e1000_tx_ring { + /* pointer to the descriptor ring memory */ + void *desc; + /* physical address of the descriptor ring */ + dma_addr_t dma; + /* length of descriptor ring in bytes */ + unsigned int size; + /* number of descriptors in the ring */ + unsigned int count; + /* next descriptor to associate a buffer with */ + unsigned int next_to_use; + /* next descriptor to check for DD status bit */ + unsigned int next_to_clean; + /* array of buffer information structs */ + struct e1000_buffer *buffer_info; + + spinlock_t tx_lock; + uint16_t tdh; + uint16_t tdt; + boolean_t last_tx_tso; +}; + +struct e1000_rx_ring { + /* pointer to the descriptor ring memory */ + void *desc; + /* physical address of the descriptor ring */ + dma_addr_t dma; + /* length of descriptor ring in bytes */ + unsigned int size; + /* number of descriptors in the ring */ + unsigned int count; + /* next descriptor to associate a buffer with */ + unsigned int next_to_use; + /* next descriptor to check for DD status bit */ + unsigned int next_to_clean; + /* array of buffer information structs */ + struct e1000_buffer *buffer_info; + /* arrays of page information for packet split */ + struct e1000_ps_page *ps_page; + struct e1000_ps_page_dma *ps_page_dma; + + /* cpu for rx queue */ + int cpu; + + uint16_t rdh; + uint16_t rdt; +}; + +#define E1000_DESC_UNUSED(R) \ + ((((R)->next_to_clean > (R)->next_to_use) ? 0 : (R)->count) + \ + (R)->next_to_clean - (R)->next_to_use - 1) + +#define E1000_RX_DESC_PS(R, i) \ + (&(((union e1000_rx_desc_packet_split *)((R).desc))[i])) +#define E1000_RX_DESC_EXT(R, i) \ + (&(((union e1000_rx_desc_extended *)((R).desc))[i])) +#define E1000_GET_DESC(R, i, type) (&(((struct type *)((R).desc))[i])) +#define E1000_RX_DESC(R, i) E1000_GET_DESC(R, i, e1000_rx_desc) +#define E1000_TX_DESC(R, i) E1000_GET_DESC(R, i, e1000_tx_desc) +#define E1000_CONTEXT_DESC(R, i) E1000_GET_DESC(R, i, e1000_context_desc) + +/* board specific private data structure */ + +struct e1000_adapter { + struct timer_list tx_fifo_stall_timer; + struct timer_list watchdog_timer; + struct timer_list phy_info_timer; + struct vlan_group *vlgrp; + uint16_t mng_vlan_id; + uint32_t bd_number; + uint32_t rx_buffer_len; + uint32_t wol; + uint32_t smartspeed; + uint32_t en_mng_pt; + uint16_t link_speed; + uint16_t link_duplex; + spinlock_t stats_lock; +#ifdef CONFIG_E1000_NAPI + spinlock_t tx_queue_lock; +#endif + atomic_t irq_sem; + unsigned int total_tx_bytes; + unsigned int total_tx_packets; + unsigned int total_rx_bytes; + unsigned int total_rx_packets; + /* Interrupt Throttle Rate */ + uint32_t itr; + uint32_t itr_setting; + uint16_t tx_itr; + uint16_t rx_itr; + + struct work_struct reset_task; + uint8_t fc_autoneg; + + struct timer_list blink_timer; + unsigned long led_status; + + /* TX */ + struct e1000_tx_ring *tx_ring; /* One per active queue */ + unsigned int restart_queue; + unsigned long tx_queue_len; + uint32_t txd_cmd; + uint32_t tx_int_delay; + uint32_t tx_abs_int_delay; + uint32_t gotcl; + uint64_t gotcl_old; + uint64_t tpt_old; + uint64_t colc_old; + uint32_t tx_timeout_count; + uint32_t tx_fifo_head; + uint32_t tx_head_addr; + uint32_t tx_fifo_size; + uint8_t tx_timeout_factor; + atomic_t tx_fifo_stall; + boolean_t pcix_82544; + boolean_t detect_tx_hung; + + /* RX */ +#ifdef CONFIG_E1000_NAPI + boolean_t (*clean_rx) (struct e1000_adapter *adapter, + struct e1000_rx_ring *rx_ring, + int *work_done, int work_to_do); +#else + boolean_t (*clean_rx) (struct e1000_adapter *adapter, + struct e1000_rx_ring *rx_ring); +#endif + void (*alloc_rx_buf) (struct e1000_adapter *adapter, + struct e1000_rx_ring *rx_ring, + int cleaned_count); + struct e1000_rx_ring *rx_ring; /* One per active queue */ +#ifdef CONFIG_E1000_NAPI + struct napi_struct napi; + struct net_device *polling_netdev; /* One per active queue */ +#endif + int num_tx_queues; + int num_rx_queues; + + uint64_t hw_csum_err; + uint64_t hw_csum_good; + uint64_t rx_hdr_split; + uint32_t alloc_rx_buff_failed; + uint32_t rx_int_delay; + uint32_t rx_abs_int_delay; + boolean_t rx_csum; + unsigned int rx_ps_pages; + uint32_t gorcl; + uint64_t gorcl_old; + uint16_t rx_ps_bsize0; + + + /* OS defined structs */ + struct net_device *netdev; + struct pci_dev *pdev; + struct net_device_stats net_stats; + + /* structs defined in e1000_hw.h */ + struct e1000_hw hw; + struct e1000_hw_stats stats; + struct e1000_phy_info phy_info; + struct e1000_phy_stats phy_stats; + + uint32_t test_icr; + struct e1000_tx_ring test_tx_ring; + struct e1000_rx_ring test_rx_ring; + + int msg_enable; + boolean_t have_msi; + + /* to not mess up cache alignment, always add to the bottom */ + boolean_t tso_force; + boolean_t smart_power_down; /* phy smart power down */ + boolean_t quad_port_a; + unsigned long flags; + uint32_t eeprom_wol; + + ec_device_t *ecdev; + unsigned long ec_watchdog_jiffies; +}; + +enum e1000_state_t { + __E1000_TESTING, + __E1000_RESETTING, + __E1000_DOWN +}; + +extern char e1000_driver_name[]; +extern const char e1000_driver_version[]; + +extern void e1000_power_up_phy(struct e1000_adapter *); +extern void e1000_set_ethtool_ops(struct net_device *netdev); +extern void e1000_check_options(struct e1000_adapter *adapter); + + +#endif /* _E1000_H_ */ diff -Nur ethercat-1.4.0/devices/e1000/e1000-2.6.32-orig.h ethercat-1.4.0.patched//devices/e1000/e1000-2.6.32-orig.h --- ethercat-1.4.0/devices/e1000/e1000-2.6.32-orig.h 1970-01-01 01:00:00.000000000 +0100 +++ ethercat-1.4.0.patched//devices/e1000/e1000-2.6.32-orig.h 2011-11-18 12:19:07.262818337 +0100 @@ -0,0 +1,362 @@ +/******************************************************************************* + + Intel PRO/1000 Linux driver + Copyright(c) 1999 - 2006 Intel Corporation. + + This program is free software; you can redistribute it and/or modify it + under the terms and conditions of the GNU General Public License, + version 2, as published by the Free Software Foundation. + + This program is distributed in the hope it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., + 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. + + The full GNU General Public License is included in this distribution in + the file called "COPYING". + + Contact Information: + Linux NICS + e1000-devel Mailing List + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + +*******************************************************************************/ + + +/* Linux PRO/1000 Ethernet Driver main header file */ + +#ifndef _E1000_H_ +#define _E1000_H_ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define BAR_0 0 +#define BAR_1 1 +#define BAR_5 5 + +#define INTEL_E1000_ETHERNET_DEVICE(device_id) {\ + PCI_DEVICE(PCI_VENDOR_ID_INTEL, device_id)} + +struct e1000_adapter; + +#include "e1000_hw.h" + +#ifdef DBG +#define E1000_DBG(args...) printk(KERN_DEBUG "e1000: " args) +#else +#define E1000_DBG(args...) +#endif + +#define E1000_ERR(args...) printk(KERN_ERR "e1000: " args) + +#define PFX "e1000: " +#define DPRINTK(nlevel, klevel, fmt, args...) \ + (void)((NETIF_MSG_##nlevel & adapter->msg_enable) && \ + printk(KERN_##klevel PFX "%s: %s: " fmt, adapter->netdev->name, \ + __FUNCTION__ , ## args)) + +#define E1000_MAX_INTR 10 + +/* TX/RX descriptor defines */ +#define E1000_DEFAULT_TXD 256 +#define E1000_MAX_TXD 256 +#define E1000_MIN_TXD 80 +#define E1000_MAX_82544_TXD 4096 + +#define E1000_DEFAULT_RXD 256 +#define E1000_MAX_RXD 256 +#define E1000_MIN_RXD 80 +#define E1000_MAX_82544_RXD 4096 + +/* this is the size past which hardware will drop packets when setting LPE=0 */ +#define MAXIMUM_ETHERNET_VLAN_SIZE 1522 + +/* Supported Rx Buffer Sizes */ +#define E1000_RXBUFFER_128 128 /* Used for packet split */ +#define E1000_RXBUFFER_256 256 /* Used for packet split */ +#define E1000_RXBUFFER_512 512 +#define E1000_RXBUFFER_1024 1024 +#define E1000_RXBUFFER_2048 2048 +#define E1000_RXBUFFER_4096 4096 +#define E1000_RXBUFFER_8192 8192 +#define E1000_RXBUFFER_16384 16384 + +/* SmartSpeed delimiters */ +#define E1000_SMARTSPEED_DOWNSHIFT 3 +#define E1000_SMARTSPEED_MAX 15 + +/* Packet Buffer allocations */ +#define E1000_PBA_BYTES_SHIFT 0xA +#define E1000_TX_HEAD_ADDR_SHIFT 7 +#define E1000_PBA_TX_MASK 0xFFFF0000 + +/* Flow Control Watermarks */ +#define E1000_FC_HIGH_DIFF 0x1638 /* High: 5688 bytes below Rx FIFO size */ +#define E1000_FC_LOW_DIFF 0x1640 /* Low: 5696 bytes below Rx FIFO size */ + +#define E1000_FC_PAUSE_TIME 0x0680 /* 858 usec */ + +/* How many Tx Descriptors do we need to call netif_wake_queue ? */ +#define E1000_TX_QUEUE_WAKE 16 +/* How many Rx Buffers do we bundle into one write to the hardware ? */ +#define E1000_RX_BUFFER_WRITE 16 /* Must be power of 2 */ + +#define AUTO_ALL_MODES 0 +#define E1000_EEPROM_82544_APM 0x0004 +#define E1000_EEPROM_ICH8_APME 0x0004 +#define E1000_EEPROM_APME 0x0400 + +#ifndef E1000_MASTER_SLAVE +/* Switch to override PHY master/slave setting */ +#define E1000_MASTER_SLAVE e1000_ms_hw_default +#endif + +#define E1000_MNG_VLAN_NONE -1 +/* Number of packet split data buffers (not including the header buffer) */ +#define PS_PAGE_BUFFERS MAX_PS_BUFFERS-1 + +/* wrapper around a pointer to a socket buffer, + * so a DMA handle can be stored along with the buffer */ +struct e1000_buffer { + struct sk_buff *skb; + dma_addr_t dma; + unsigned long time_stamp; + uint16_t length; + uint16_t next_to_watch; +}; + + +struct e1000_ps_page { struct page *ps_page[PS_PAGE_BUFFERS]; }; +struct e1000_ps_page_dma { uint64_t ps_page_dma[PS_PAGE_BUFFERS]; }; + +struct e1000_tx_ring { + /* pointer to the descriptor ring memory */ + void *desc; + /* physical address of the descriptor ring */ + dma_addr_t dma; + /* length of descriptor ring in bytes */ + unsigned int size; + /* number of descriptors in the ring */ + unsigned int count; + /* next descriptor to associate a buffer with */ + unsigned int next_to_use; + /* next descriptor to check for DD status bit */ + unsigned int next_to_clean; + /* array of buffer information structs */ + struct e1000_buffer *buffer_info; + + spinlock_t tx_lock; + uint16_t tdh; + uint16_t tdt; + boolean_t last_tx_tso; +}; + +struct e1000_rx_ring { + /* pointer to the descriptor ring memory */ + void *desc; + /* physical address of the descriptor ring */ + dma_addr_t dma; + /* length of descriptor ring in bytes */ + unsigned int size; + /* number of descriptors in the ring */ + unsigned int count; + /* next descriptor to associate a buffer with */ + unsigned int next_to_use; + /* next descriptor to check for DD status bit */ + unsigned int next_to_clean; + /* array of buffer information structs */ + struct e1000_buffer *buffer_info; + /* arrays of page information for packet split */ + struct e1000_ps_page *ps_page; + struct e1000_ps_page_dma *ps_page_dma; + + /* cpu for rx queue */ + int cpu; + + uint16_t rdh; + uint16_t rdt; +}; + +#define E1000_DESC_UNUSED(R) \ + ((((R)->next_to_clean > (R)->next_to_use) ? 0 : (R)->count) + \ + (R)->next_to_clean - (R)->next_to_use - 1) + +#define E1000_RX_DESC_PS(R, i) \ + (&(((union e1000_rx_desc_packet_split *)((R).desc))[i])) +#define E1000_RX_DESC_EXT(R, i) \ + (&(((union e1000_rx_desc_extended *)((R).desc))[i])) +#define E1000_GET_DESC(R, i, type) (&(((struct type *)((R).desc))[i])) +#define E1000_RX_DESC(R, i) E1000_GET_DESC(R, i, e1000_rx_desc) +#define E1000_TX_DESC(R, i) E1000_GET_DESC(R, i, e1000_tx_desc) +#define E1000_CONTEXT_DESC(R, i) E1000_GET_DESC(R, i, e1000_context_desc) + +/* board specific private data structure */ + +struct e1000_adapter { + struct timer_list tx_fifo_stall_timer; + struct timer_list watchdog_timer; + struct timer_list phy_info_timer; + struct vlan_group *vlgrp; + uint16_t mng_vlan_id; + uint32_t bd_number; + uint32_t rx_buffer_len; + uint32_t wol; + uint32_t smartspeed; + uint32_t en_mng_pt; + uint16_t link_speed; + uint16_t link_duplex; + spinlock_t stats_lock; +#ifdef CONFIG_E1000_NAPI + spinlock_t tx_queue_lock; +#endif + atomic_t irq_sem; + unsigned int total_tx_bytes; + unsigned int total_tx_packets; + unsigned int total_rx_bytes; + unsigned int total_rx_packets; + /* Interrupt Throttle Rate */ + uint32_t itr; + uint32_t itr_setting; + uint16_t tx_itr; + uint16_t rx_itr; + + struct work_struct reset_task; + uint8_t fc_autoneg; + + struct timer_list blink_timer; + unsigned long led_status; + + /* TX */ + struct e1000_tx_ring *tx_ring; /* One per active queue */ + unsigned int restart_queue; + unsigned long tx_queue_len; + uint32_t txd_cmd; + uint32_t tx_int_delay; + uint32_t tx_abs_int_delay; + uint32_t gotcl; + uint64_t gotcl_old; + uint64_t tpt_old; + uint64_t colc_old; + uint32_t tx_timeout_count; + uint32_t tx_fifo_head; + uint32_t tx_head_addr; + uint32_t tx_fifo_size; + uint8_t tx_timeout_factor; + atomic_t tx_fifo_stall; + boolean_t pcix_82544; + boolean_t detect_tx_hung; + + /* RX */ +#ifdef CONFIG_E1000_NAPI + boolean_t (*clean_rx) (struct e1000_adapter *adapter, + struct e1000_rx_ring *rx_ring, + int *work_done, int work_to_do); +#else + boolean_t (*clean_rx) (struct e1000_adapter *adapter, + struct e1000_rx_ring *rx_ring); +#endif + void (*alloc_rx_buf) (struct e1000_adapter *adapter, + struct e1000_rx_ring *rx_ring, + int cleaned_count); + struct e1000_rx_ring *rx_ring; /* One per active queue */ +#ifdef CONFIG_E1000_NAPI + struct napi_struct napi; + struct net_device *polling_netdev; /* One per active queue */ +#endif + int num_tx_queues; + int num_rx_queues; + + uint64_t hw_csum_err; + uint64_t hw_csum_good; + uint64_t rx_hdr_split; + uint32_t alloc_rx_buff_failed; + uint32_t rx_int_delay; + uint32_t rx_abs_int_delay; + boolean_t rx_csum; + unsigned int rx_ps_pages; + uint32_t gorcl; + uint64_t gorcl_old; + uint16_t rx_ps_bsize0; + + + /* OS defined structs */ + struct net_device *netdev; + struct pci_dev *pdev; + struct net_device_stats net_stats; + + /* structs defined in e1000_hw.h */ + struct e1000_hw hw; + struct e1000_hw_stats stats; + struct e1000_phy_info phy_info; + struct e1000_phy_stats phy_stats; + + uint32_t test_icr; + struct e1000_tx_ring test_tx_ring; + struct e1000_rx_ring test_rx_ring; + + int msg_enable; + boolean_t have_msi; + + /* to not mess up cache alignment, always add to the bottom */ + boolean_t tso_force; + boolean_t smart_power_down; /* phy smart power down */ + boolean_t quad_port_a; + unsigned long flags; + uint32_t eeprom_wol; +}; + +enum e1000_state_t { + __E1000_TESTING, + __E1000_RESETTING, + __E1000_DOWN +}; + +extern char e1000_driver_name[]; +extern const char e1000_driver_version[]; + +extern void e1000_power_up_phy(struct e1000_adapter *); +extern void e1000_set_ethtool_ops(struct net_device *netdev); +extern void e1000_check_options(struct e1000_adapter *adapter); + + +#endif /* _E1000_H_ */ diff -Nur ethercat-1.4.0/devices/e1000/e1000_ethtool-2.6.32-ethercat.c ethercat-1.4.0.patched//devices/e1000/e1000_ethtool-2.6.32-ethercat.c --- ethercat-1.4.0/devices/e1000/e1000_ethtool-2.6.32-ethercat.c 1970-01-01 01:00:00.000000000 +0100 +++ ethercat-1.4.0.patched//devices/e1000/e1000_ethtool-2.6.32-ethercat.c 2011-11-18 12:19:07.270817245 +0100 @@ -0,0 +1,1997 @@ +/******************************************************************************* + + Intel PRO/1000 Linux driver + Copyright(c) 1999 - 2006 Intel Corporation. + + This program is free software; you can redistribute it and/or modify it + under the terms and conditions of the GNU General Public License, + version 2, as published by the Free Software Foundation. + + This program is distributed in the hope it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., + 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. + + The full GNU General Public License is included in this distribution in + the file called "COPYING". + + Contact Information: + Linux NICS + e1000-devel Mailing List + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + +*******************************************************************************/ + +/* ethtool support for e1000 */ + +#include "e1000-2.6.24-ethercat.h" + +#include + +extern int e1000_up(struct e1000_adapter *adapter); +extern void e1000_down(struct e1000_adapter *adapter); +extern void e1000_reinit_locked(struct e1000_adapter *adapter); +extern void e1000_reset(struct e1000_adapter *adapter); +extern int e1000_set_spd_dplx(struct e1000_adapter *adapter, uint16_t spddplx); +extern int e1000_setup_all_rx_resources(struct e1000_adapter *adapter); +extern int e1000_setup_all_tx_resources(struct e1000_adapter *adapter); +extern void e1000_free_all_rx_resources(struct e1000_adapter *adapter); +extern void e1000_free_all_tx_resources(struct e1000_adapter *adapter); +extern void e1000_update_stats(struct e1000_adapter *adapter); + + +struct e1000_stats { + char stat_string[ETH_GSTRING_LEN]; + int sizeof_stat; + int stat_offset; +}; + +#define E1000_STAT(m) sizeof(((struct e1000_adapter *)0)->m), \ + offsetof(struct e1000_adapter, m) +static const struct e1000_stats e1000_gstrings_stats[] = { + { "rx_packets", E1000_STAT(stats.gprc) }, + { "tx_packets", E1000_STAT(stats.gptc) }, + { "rx_bytes", E1000_STAT(stats.gorcl) }, + { "tx_bytes", E1000_STAT(stats.gotcl) }, + { "rx_broadcast", E1000_STAT(stats.bprc) }, + { "tx_broadcast", E1000_STAT(stats.bptc) }, + { "rx_multicast", E1000_STAT(stats.mprc) }, + { "tx_multicast", E1000_STAT(stats.mptc) }, + { "rx_errors", E1000_STAT(stats.rxerrc) }, + { "tx_errors", E1000_STAT(stats.txerrc) }, + { "tx_dropped", E1000_STAT(net_stats.tx_dropped) }, + { "multicast", E1000_STAT(stats.mprc) }, + { "collisions", E1000_STAT(stats.colc) }, + { "rx_length_errors", E1000_STAT(stats.rlerrc) }, + { "rx_over_errors", E1000_STAT(net_stats.rx_over_errors) }, + { "rx_crc_errors", E1000_STAT(stats.crcerrs) }, + { "rx_frame_errors", E1000_STAT(net_stats.rx_frame_errors) }, + { "rx_no_buffer_count", E1000_STAT(stats.rnbc) }, + { "rx_missed_errors", E1000_STAT(stats.mpc) }, + { "tx_aborted_errors", E1000_STAT(stats.ecol) }, + { "tx_carrier_errors", E1000_STAT(stats.tncrs) }, + { "tx_fifo_errors", E1000_STAT(net_stats.tx_fifo_errors) }, + { "tx_heartbeat_errors", E1000_STAT(net_stats.tx_heartbeat_errors) }, + { "tx_window_errors", E1000_STAT(stats.latecol) }, + { "tx_abort_late_coll", E1000_STAT(stats.latecol) }, + { "tx_deferred_ok", E1000_STAT(stats.dc) }, + { "tx_single_coll_ok", E1000_STAT(stats.scc) }, + { "tx_multi_coll_ok", E1000_STAT(stats.mcc) }, + { "tx_timeout_count", E1000_STAT(tx_timeout_count) }, + { "tx_restart_queue", E1000_STAT(restart_queue) }, + { "rx_long_length_errors", E1000_STAT(stats.roc) }, + { "rx_short_length_errors", E1000_STAT(stats.ruc) }, + { "rx_align_errors", E1000_STAT(stats.algnerrc) }, + { "tx_tcp_seg_good", E1000_STAT(stats.tsctc) }, + { "tx_tcp_seg_failed", E1000_STAT(stats.tsctfc) }, + { "rx_flow_control_xon", E1000_STAT(stats.xonrxc) }, + { "rx_flow_control_xoff", E1000_STAT(stats.xoffrxc) }, + { "tx_flow_control_xon", E1000_STAT(stats.xontxc) }, + { "tx_flow_control_xoff", E1000_STAT(stats.xofftxc) }, + { "rx_long_byte_count", E1000_STAT(stats.gorcl) }, + { "rx_csum_offload_good", E1000_STAT(hw_csum_good) }, + { "rx_csum_offload_errors", E1000_STAT(hw_csum_err) }, + { "rx_header_split", E1000_STAT(rx_hdr_split) }, + { "alloc_rx_buff_failed", E1000_STAT(alloc_rx_buff_failed) }, + { "tx_smbus", E1000_STAT(stats.mgptc) }, + { "rx_smbus", E1000_STAT(stats.mgprc) }, + { "dropped_smbus", E1000_STAT(stats.mgpdc) }, +}; + +#define E1000_QUEUE_STATS_LEN 0 +#define E1000_GLOBAL_STATS_LEN ARRAY_SIZE(e1000_gstrings_stats) +#define E1000_STATS_LEN (E1000_GLOBAL_STATS_LEN + E1000_QUEUE_STATS_LEN) +static const char e1000_gstrings_test[][ETH_GSTRING_LEN] = { + "Register test (offline)", "Eeprom test (offline)", + "Interrupt test (offline)", "Loopback test (offline)", + "Link test (on/offline)" +}; +#define E1000_TEST_LEN sizeof(e1000_gstrings_test) / ETH_GSTRING_LEN + +static int +e1000_get_settings(struct net_device *netdev, struct ethtool_cmd *ecmd) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + struct e1000_hw *hw = &adapter->hw; + + if (hw->media_type == e1000_media_type_copper) { + + ecmd->supported = (SUPPORTED_10baseT_Half | + SUPPORTED_10baseT_Full | + SUPPORTED_100baseT_Half | + SUPPORTED_100baseT_Full | + SUPPORTED_1000baseT_Full| + SUPPORTED_Autoneg | + SUPPORTED_TP); + if (hw->phy_type == e1000_phy_ife) + ecmd->supported &= ~SUPPORTED_1000baseT_Full; + ecmd->advertising = ADVERTISED_TP; + + if (hw->autoneg == 1) { + ecmd->advertising |= ADVERTISED_Autoneg; + /* the e1000 autoneg seems to match ethtool nicely */ + ecmd->advertising |= hw->autoneg_advertised; + } + + ecmd->port = PORT_TP; + ecmd->phy_address = hw->phy_addr; + + if (hw->mac_type == e1000_82543) + ecmd->transceiver = XCVR_EXTERNAL; + else + ecmd->transceiver = XCVR_INTERNAL; + + } else { + ecmd->supported = (SUPPORTED_1000baseT_Full | + SUPPORTED_FIBRE | + SUPPORTED_Autoneg); + + ecmd->advertising = (ADVERTISED_1000baseT_Full | + ADVERTISED_FIBRE | + ADVERTISED_Autoneg); + + ecmd->port = PORT_FIBRE; + + if (hw->mac_type >= e1000_82545) + ecmd->transceiver = XCVR_INTERNAL; + else + ecmd->transceiver = XCVR_EXTERNAL; + } + + if ((adapter->ecdev && ecdev_get_link(adapter->ecdev)) + || (!adapter->ecdev && (E1000_READ_REG(&adapter->hw, STATUS) & E1000_STATUS_LU))) { + + e1000_get_speed_and_duplex(hw, &adapter->link_speed, + &adapter->link_duplex); + ecmd->speed = adapter->link_speed; + + /* unfortunatly FULL_DUPLEX != DUPLEX_FULL + * and HALF_DUPLEX != DUPLEX_HALF */ + + if (adapter->link_duplex == FULL_DUPLEX) + ecmd->duplex = DUPLEX_FULL; + else + ecmd->duplex = DUPLEX_HALF; + } else { + ecmd->speed = -1; + ecmd->duplex = -1; + } + + ecmd->autoneg = ((hw->media_type == e1000_media_type_fiber) || + hw->autoneg) ? AUTONEG_ENABLE : AUTONEG_DISABLE; + return 0; +} + +static int +e1000_set_settings(struct net_device *netdev, struct ethtool_cmd *ecmd) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + struct e1000_hw *hw = &adapter->hw; + + if (adapter->ecdev) + return -EBUSY; + + /* When SoL/IDER sessions are active, autoneg/speed/duplex + * cannot be changed */ + if (e1000_check_phy_reset_block(hw)) { + DPRINTK(DRV, ERR, "Cannot change link characteristics " + "when SoL/IDER is active.\n"); + return -EINVAL; + } + + while (test_and_set_bit(__E1000_RESETTING, &adapter->flags)) + msleep(1); + + if (ecmd->autoneg == AUTONEG_ENABLE) { + hw->autoneg = 1; + if (hw->media_type == e1000_media_type_fiber) + hw->autoneg_advertised = ADVERTISED_1000baseT_Full | + ADVERTISED_FIBRE | + ADVERTISED_Autoneg; + else + hw->autoneg_advertised = ecmd->advertising | + ADVERTISED_TP | + ADVERTISED_Autoneg; + ecmd->advertising = hw->autoneg_advertised; + } else + if (e1000_set_spd_dplx(adapter, ecmd->speed + ecmd->duplex)) { + clear_bit(__E1000_RESETTING, &adapter->flags); + return -EINVAL; + } + + /* reset the link */ + + if (netif_running(adapter->netdev)) { + e1000_down(adapter); + e1000_up(adapter); + } else + e1000_reset(adapter); + + clear_bit(__E1000_RESETTING, &adapter->flags); + return 0; +} + +static void +e1000_get_pauseparam(struct net_device *netdev, + struct ethtool_pauseparam *pause) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + struct e1000_hw *hw = &adapter->hw; + + pause->autoneg = + (adapter->fc_autoneg ? AUTONEG_ENABLE : AUTONEG_DISABLE); + + if (hw->fc == E1000_FC_RX_PAUSE) + pause->rx_pause = 1; + else if (hw->fc == E1000_FC_TX_PAUSE) + pause->tx_pause = 1; + else if (hw->fc == E1000_FC_FULL) { + pause->rx_pause = 1; + pause->tx_pause = 1; + } +} + +static int +e1000_set_pauseparam(struct net_device *netdev, + struct ethtool_pauseparam *pause) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + struct e1000_hw *hw = &adapter->hw; + int retval = 0; + + if (adapter->ecdev) + return -EBUSY; + + adapter->fc_autoneg = pause->autoneg; + + while (test_and_set_bit(__E1000_RESETTING, &adapter->flags)) + msleep(1); + + if (pause->rx_pause && pause->tx_pause) + hw->fc = E1000_FC_FULL; + else if (pause->rx_pause && !pause->tx_pause) + hw->fc = E1000_FC_RX_PAUSE; + else if (!pause->rx_pause && pause->tx_pause) + hw->fc = E1000_FC_TX_PAUSE; + else if (!pause->rx_pause && !pause->tx_pause) + hw->fc = E1000_FC_NONE; + + hw->original_fc = hw->fc; + + if (adapter->fc_autoneg == AUTONEG_ENABLE) { + if (netif_running(adapter->netdev)) { + e1000_down(adapter); + e1000_up(adapter); + } else + e1000_reset(adapter); + } else + retval = ((hw->media_type == e1000_media_type_fiber) ? + e1000_setup_link(hw) : e1000_force_mac_fc(hw)); + + clear_bit(__E1000_RESETTING, &adapter->flags); + return retval; +} + +static uint32_t +e1000_get_rx_csum(struct net_device *netdev) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + return adapter->rx_csum; +} + +static int +e1000_set_rx_csum(struct net_device *netdev, uint32_t data) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + + if (adapter->ecdev) + return -EBUSY; + + adapter->rx_csum = data; + + if (netif_running(netdev)) + e1000_reinit_locked(adapter); + else + e1000_reset(adapter); + return 0; +} + +static uint32_t +e1000_get_tx_csum(struct net_device *netdev) +{ + return (netdev->features & NETIF_F_HW_CSUM) != 0; +} + +static int +e1000_set_tx_csum(struct net_device *netdev, uint32_t data) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + + if (adapter->hw.mac_type < e1000_82543) { + if (!data) + return -EINVAL; + return 0; + } + + if (data) + netdev->features |= NETIF_F_HW_CSUM; + else + netdev->features &= ~NETIF_F_HW_CSUM; + + return 0; +} + +static int +e1000_set_tso(struct net_device *netdev, uint32_t data) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + if ((adapter->hw.mac_type < e1000_82544) || + (adapter->hw.mac_type == e1000_82547)) + return data ? -EINVAL : 0; + + if (data) + netdev->features |= NETIF_F_TSO; + else + netdev->features &= ~NETIF_F_TSO; + + if (data) + netdev->features |= NETIF_F_TSO6; + else + netdev->features &= ~NETIF_F_TSO6; + + DPRINTK(PROBE, INFO, "TSO is %s\n", data ? "Enabled" : "Disabled"); + adapter->tso_force = TRUE; + return 0; +} + +static uint32_t +e1000_get_msglevel(struct net_device *netdev) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + return adapter->msg_enable; +} + +static void +e1000_set_msglevel(struct net_device *netdev, uint32_t data) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + adapter->msg_enable = data; +} + +static int +e1000_get_regs_len(struct net_device *netdev) +{ +#define E1000_REGS_LEN 32 + return E1000_REGS_LEN * sizeof(uint32_t); +} + +static void +e1000_get_regs(struct net_device *netdev, + struct ethtool_regs *regs, void *p) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + struct e1000_hw *hw = &adapter->hw; + uint32_t *regs_buff = p; + uint16_t phy_data; + + memset(p, 0, E1000_REGS_LEN * sizeof(uint32_t)); + + regs->version = (1 << 24) | (hw->revision_id << 16) | hw->device_id; + + regs_buff[0] = E1000_READ_REG(hw, CTRL); + regs_buff[1] = E1000_READ_REG(hw, STATUS); + + regs_buff[2] = E1000_READ_REG(hw, RCTL); + regs_buff[3] = E1000_READ_REG(hw, RDLEN); + regs_buff[4] = E1000_READ_REG(hw, RDH); + regs_buff[5] = E1000_READ_REG(hw, RDT); + regs_buff[6] = E1000_READ_REG(hw, RDTR); + + regs_buff[7] = E1000_READ_REG(hw, TCTL); + regs_buff[8] = E1000_READ_REG(hw, TDLEN); + regs_buff[9] = E1000_READ_REG(hw, TDH); + regs_buff[10] = E1000_READ_REG(hw, TDT); + regs_buff[11] = E1000_READ_REG(hw, TIDV); + + regs_buff[12] = adapter->hw.phy_type; /* PHY type (IGP=1, M88=0) */ + if (hw->phy_type == e1000_phy_igp) { + e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT, + IGP01E1000_PHY_AGC_A); + e1000_read_phy_reg(hw, IGP01E1000_PHY_AGC_A & + IGP01E1000_PHY_PAGE_SELECT, &phy_data); + regs_buff[13] = (uint32_t)phy_data; /* cable length */ + e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT, + IGP01E1000_PHY_AGC_B); + e1000_read_phy_reg(hw, IGP01E1000_PHY_AGC_B & + IGP01E1000_PHY_PAGE_SELECT, &phy_data); + regs_buff[14] = (uint32_t)phy_data; /* cable length */ + e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT, + IGP01E1000_PHY_AGC_C); + e1000_read_phy_reg(hw, IGP01E1000_PHY_AGC_C & + IGP01E1000_PHY_PAGE_SELECT, &phy_data); + regs_buff[15] = (uint32_t)phy_data; /* cable length */ + e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT, + IGP01E1000_PHY_AGC_D); + e1000_read_phy_reg(hw, IGP01E1000_PHY_AGC_D & + IGP01E1000_PHY_PAGE_SELECT, &phy_data); + regs_buff[16] = (uint32_t)phy_data; /* cable length */ + regs_buff[17] = 0; /* extended 10bt distance (not needed) */ + e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT, 0x0); + e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS & + IGP01E1000_PHY_PAGE_SELECT, &phy_data); + regs_buff[18] = (uint32_t)phy_data; /* cable polarity */ + e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT, + IGP01E1000_PHY_PCS_INIT_REG); + e1000_read_phy_reg(hw, IGP01E1000_PHY_PCS_INIT_REG & + IGP01E1000_PHY_PAGE_SELECT, &phy_data); + regs_buff[19] = (uint32_t)phy_data; /* cable polarity */ + regs_buff[20] = 0; /* polarity correction enabled (always) */ + regs_buff[22] = 0; /* phy receive errors (unavailable) */ + regs_buff[23] = regs_buff[18]; /* mdix mode */ + e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT, 0x0); + } else { + e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data); + regs_buff[13] = (uint32_t)phy_data; /* cable length */ + regs_buff[14] = 0; /* Dummy (to align w/ IGP phy reg dump) */ + regs_buff[15] = 0; /* Dummy (to align w/ IGP phy reg dump) */ + regs_buff[16] = 0; /* Dummy (to align w/ IGP phy reg dump) */ + e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + regs_buff[17] = (uint32_t)phy_data; /* extended 10bt distance */ + regs_buff[18] = regs_buff[13]; /* cable polarity */ + regs_buff[19] = 0; /* Dummy (to align w/ IGP phy reg dump) */ + regs_buff[20] = regs_buff[17]; /* polarity correction */ + /* phy receive errors */ + regs_buff[22] = adapter->phy_stats.receive_errors; + regs_buff[23] = regs_buff[13]; /* mdix mode */ + } + regs_buff[21] = adapter->phy_stats.idle_errors; /* phy idle errors */ + e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data); + regs_buff[24] = (uint32_t)phy_data; /* phy local receiver status */ + regs_buff[25] = regs_buff[24]; /* phy remote receiver status */ + if (hw->mac_type >= e1000_82540 && + hw->mac_type < e1000_82571 && + hw->media_type == e1000_media_type_copper) { + regs_buff[26] = E1000_READ_REG(hw, MANC); + } +} + +static int +e1000_get_eeprom_len(struct net_device *netdev) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + return adapter->hw.eeprom.word_size * 2; +} + +static int +e1000_get_eeprom(struct net_device *netdev, + struct ethtool_eeprom *eeprom, uint8_t *bytes) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + struct e1000_hw *hw = &adapter->hw; + uint16_t *eeprom_buff; + int first_word, last_word; + int ret_val = 0; + uint16_t i; + + if (eeprom->len == 0) + return -EINVAL; + + eeprom->magic = hw->vendor_id | (hw->device_id << 16); + + first_word = eeprom->offset >> 1; + last_word = (eeprom->offset + eeprom->len - 1) >> 1; + + eeprom_buff = kmalloc(sizeof(uint16_t) * + (last_word - first_word + 1), GFP_KERNEL); + if (!eeprom_buff) + return -ENOMEM; + + if (hw->eeprom.type == e1000_eeprom_spi) + ret_val = e1000_read_eeprom(hw, first_word, + last_word - first_word + 1, + eeprom_buff); + else { + for (i = 0; i < last_word - first_word + 1; i++) + if ((ret_val = e1000_read_eeprom(hw, first_word + i, 1, + &eeprom_buff[i]))) + break; + } + + /* Device's eeprom is always little-endian, word addressable */ + for (i = 0; i < last_word - first_word + 1; i++) + le16_to_cpus(&eeprom_buff[i]); + + memcpy(bytes, (uint8_t *)eeprom_buff + (eeprom->offset & 1), + eeprom->len); + kfree(eeprom_buff); + + return ret_val; +} + +static int +e1000_set_eeprom(struct net_device *netdev, + struct ethtool_eeprom *eeprom, uint8_t *bytes) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + struct e1000_hw *hw = &adapter->hw; + uint16_t *eeprom_buff; + void *ptr; + int max_len, first_word, last_word, ret_val = 0; + uint16_t i; + + if (eeprom->len == 0) + return -EOPNOTSUPP; + + if (eeprom->magic != (hw->vendor_id | (hw->device_id << 16))) + return -EFAULT; + + max_len = hw->eeprom.word_size * 2; + + first_word = eeprom->offset >> 1; + last_word = (eeprom->offset + eeprom->len - 1) >> 1; + eeprom_buff = kmalloc(max_len, GFP_KERNEL); + if (!eeprom_buff) + return -ENOMEM; + + ptr = (void *)eeprom_buff; + + if (eeprom->offset & 1) { + /* need read/modify/write of first changed EEPROM word */ + /* only the second byte of the word is being modified */ + ret_val = e1000_read_eeprom(hw, first_word, 1, + &eeprom_buff[0]); + ptr++; + } + if (((eeprom->offset + eeprom->len) & 1) && (ret_val == 0)) { + /* need read/modify/write of last changed EEPROM word */ + /* only the first byte of the word is being modified */ + ret_val = e1000_read_eeprom(hw, last_word, 1, + &eeprom_buff[last_word - first_word]); + } + + /* Device's eeprom is always little-endian, word addressable */ + for (i = 0; i < last_word - first_word + 1; i++) + le16_to_cpus(&eeprom_buff[i]); + + memcpy(ptr, bytes, eeprom->len); + + for (i = 0; i < last_word - first_word + 1; i++) + eeprom_buff[i] = cpu_to_le16(eeprom_buff[i]); + + ret_val = e1000_write_eeprom(hw, first_word, + last_word - first_word + 1, eeprom_buff); + + /* Update the checksum over the first part of the EEPROM if needed + * and flush shadow RAM for 82573 conrollers */ + if ((ret_val == 0) && ((first_word <= EEPROM_CHECKSUM_REG) || + (hw->mac_type == e1000_82573))) + e1000_update_eeprom_checksum(hw); + + kfree(eeprom_buff); + return ret_val; +} + +static void +e1000_get_drvinfo(struct net_device *netdev, + struct ethtool_drvinfo *drvinfo) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + char firmware_version[32]; + uint16_t eeprom_data; + + strncpy(drvinfo->driver, e1000_driver_name, 32); + strncpy(drvinfo->version, e1000_driver_version, 32); + + /* EEPROM image version # is reported as firmware version # for + * 8257{1|2|3} controllers */ + e1000_read_eeprom(&adapter->hw, 5, 1, &eeprom_data); + switch (adapter->hw.mac_type) { + case e1000_82571: + case e1000_82572: + case e1000_82573: + case e1000_80003es2lan: + case e1000_ich8lan: + sprintf(firmware_version, "%d.%d-%d", + (eeprom_data & 0xF000) >> 12, + (eeprom_data & 0x0FF0) >> 4, + eeprom_data & 0x000F); + break; + default: + sprintf(firmware_version, "N/A"); + } + + strncpy(drvinfo->fw_version, firmware_version, 32); + strncpy(drvinfo->bus_info, pci_name(adapter->pdev), 32); + drvinfo->regdump_len = e1000_get_regs_len(netdev); + drvinfo->eedump_len = e1000_get_eeprom_len(netdev); +} + +static void +e1000_get_ringparam(struct net_device *netdev, + struct ethtool_ringparam *ring) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + e1000_mac_type mac_type = adapter->hw.mac_type; + struct e1000_tx_ring *txdr = adapter->tx_ring; + struct e1000_rx_ring *rxdr = adapter->rx_ring; + + ring->rx_max_pending = (mac_type < e1000_82544) ? E1000_MAX_RXD : + E1000_MAX_82544_RXD; + ring->tx_max_pending = (mac_type < e1000_82544) ? E1000_MAX_TXD : + E1000_MAX_82544_TXD; + ring->rx_mini_max_pending = 0; + ring->rx_jumbo_max_pending = 0; + ring->rx_pending = rxdr->count; + ring->tx_pending = txdr->count; + ring->rx_mini_pending = 0; + ring->rx_jumbo_pending = 0; +} + +static int +e1000_set_ringparam(struct net_device *netdev, + struct ethtool_ringparam *ring) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + e1000_mac_type mac_type = adapter->hw.mac_type; + struct e1000_tx_ring *txdr, *tx_old; + struct e1000_rx_ring *rxdr, *rx_old; + int i, err; + + if (adapter->ecdev) + return -EBUSY; + + if ((ring->rx_mini_pending) || (ring->rx_jumbo_pending)) + return -EINVAL; + + while (test_and_set_bit(__E1000_RESETTING, &adapter->flags)) + msleep(1); + + if (netif_running(adapter->netdev)) + e1000_down(adapter); + + tx_old = adapter->tx_ring; + rx_old = adapter->rx_ring; + + err = -ENOMEM; + txdr = kcalloc(adapter->num_tx_queues, sizeof(struct e1000_tx_ring), GFP_KERNEL); + if (!txdr) + goto err_alloc_tx; + + rxdr = kcalloc(adapter->num_rx_queues, sizeof(struct e1000_rx_ring), GFP_KERNEL); + if (!rxdr) + goto err_alloc_rx; + + adapter->tx_ring = txdr; + adapter->rx_ring = rxdr; + + rxdr->count = max(ring->rx_pending,(uint32_t)E1000_MIN_RXD); + rxdr->count = min(rxdr->count,(uint32_t)(mac_type < e1000_82544 ? + E1000_MAX_RXD : E1000_MAX_82544_RXD)); + rxdr->count = ALIGN(rxdr->count, REQ_RX_DESCRIPTOR_MULTIPLE); + + txdr->count = max(ring->tx_pending,(uint32_t)E1000_MIN_TXD); + txdr->count = min(txdr->count,(uint32_t)(mac_type < e1000_82544 ? + E1000_MAX_TXD : E1000_MAX_82544_TXD)); + txdr->count = ALIGN(txdr->count, REQ_TX_DESCRIPTOR_MULTIPLE); + + for (i = 0; i < adapter->num_tx_queues; i++) + txdr[i].count = txdr->count; + for (i = 0; i < adapter->num_rx_queues; i++) + rxdr[i].count = rxdr->count; + + if (netif_running(adapter->netdev)) { + /* Try to get new resources before deleting old */ + if ((err = e1000_setup_all_rx_resources(adapter))) + goto err_setup_rx; + if ((err = e1000_setup_all_tx_resources(adapter))) + goto err_setup_tx; + + /* save the new, restore the old in order to free it, + * then restore the new back again */ + + adapter->rx_ring = rx_old; + adapter->tx_ring = tx_old; + e1000_free_all_rx_resources(adapter); + e1000_free_all_tx_resources(adapter); + kfree(tx_old); + kfree(rx_old); + adapter->rx_ring = rxdr; + adapter->tx_ring = txdr; + if ((err = e1000_up(adapter))) + goto err_setup; + } + + clear_bit(__E1000_RESETTING, &adapter->flags); + return 0; +err_setup_tx: + e1000_free_all_rx_resources(adapter); +err_setup_rx: + adapter->rx_ring = rx_old; + adapter->tx_ring = tx_old; + kfree(rxdr); +err_alloc_rx: + kfree(txdr); +err_alloc_tx: + e1000_up(adapter); +err_setup: + clear_bit(__E1000_RESETTING, &adapter->flags); + return err; +} + +#define REG_PATTERN_TEST(R, M, W) \ +{ \ + uint32_t pat, val; \ + const uint32_t test[] = \ + {0x5A5A5A5A, 0xA5A5A5A5, 0x00000000, 0xFFFFFFFF}; \ + for (pat = 0; pat < ARRAY_SIZE(test); pat++) { \ + E1000_WRITE_REG(&adapter->hw, R, (test[pat] & W)); \ + val = E1000_READ_REG(&adapter->hw, R); \ + if (val != (test[pat] & W & M)) { \ + DPRINTK(DRV, ERR, "pattern test reg %04X failed: got " \ + "0x%08X expected 0x%08X\n", \ + E1000_##R, val, (test[pat] & W & M)); \ + *data = (adapter->hw.mac_type < e1000_82543) ? \ + E1000_82542_##R : E1000_##R; \ + return 1; \ + } \ + } \ +} + +#define REG_SET_AND_CHECK(R, M, W) \ +{ \ + uint32_t val; \ + E1000_WRITE_REG(&adapter->hw, R, W & M); \ + val = E1000_READ_REG(&adapter->hw, R); \ + if ((W & M) != (val & M)) { \ + DPRINTK(DRV, ERR, "set/check reg %04X test failed: got 0x%08X "\ + "expected 0x%08X\n", E1000_##R, (val & M), (W & M)); \ + *data = (adapter->hw.mac_type < e1000_82543) ? \ + E1000_82542_##R : E1000_##R; \ + return 1; \ + } \ +} + +static int +e1000_reg_test(struct e1000_adapter *adapter, uint64_t *data) +{ + uint32_t value, before, after; + uint32_t i, toggle; + + /* The status register is Read Only, so a write should fail. + * Some bits that get toggled are ignored. + */ + switch (adapter->hw.mac_type) { + /* there are several bits on newer hardware that are r/w */ + case e1000_82571: + case e1000_82572: + case e1000_80003es2lan: + toggle = 0x7FFFF3FF; + break; + case e1000_82573: + case e1000_ich8lan: + toggle = 0x7FFFF033; + break; + default: + toggle = 0xFFFFF833; + break; + } + + before = E1000_READ_REG(&adapter->hw, STATUS); + value = (E1000_READ_REG(&adapter->hw, STATUS) & toggle); + E1000_WRITE_REG(&adapter->hw, STATUS, toggle); + after = E1000_READ_REG(&adapter->hw, STATUS) & toggle; + if (value != after) { + DPRINTK(DRV, ERR, "failed STATUS register test got: " + "0x%08X expected: 0x%08X\n", after, value); + *data = 1; + return 1; + } + /* restore previous status */ + E1000_WRITE_REG(&adapter->hw, STATUS, before); + + if (adapter->hw.mac_type != e1000_ich8lan) { + REG_PATTERN_TEST(FCAL, 0xFFFFFFFF, 0xFFFFFFFF); + REG_PATTERN_TEST(FCAH, 0x0000FFFF, 0xFFFFFFFF); + REG_PATTERN_TEST(FCT, 0x0000FFFF, 0xFFFFFFFF); + REG_PATTERN_TEST(VET, 0x0000FFFF, 0xFFFFFFFF); + } + + REG_PATTERN_TEST(RDTR, 0x0000FFFF, 0xFFFFFFFF); + REG_PATTERN_TEST(RDBAH, 0xFFFFFFFF, 0xFFFFFFFF); + REG_PATTERN_TEST(RDLEN, 0x000FFF80, 0x000FFFFF); + REG_PATTERN_TEST(RDH, 0x0000FFFF, 0x0000FFFF); + REG_PATTERN_TEST(RDT, 0x0000FFFF, 0x0000FFFF); + REG_PATTERN_TEST(FCRTH, 0x0000FFF8, 0x0000FFF8); + REG_PATTERN_TEST(FCTTV, 0x0000FFFF, 0x0000FFFF); + REG_PATTERN_TEST(TIPG, 0x3FFFFFFF, 0x3FFFFFFF); + REG_PATTERN_TEST(TDBAH, 0xFFFFFFFF, 0xFFFFFFFF); + REG_PATTERN_TEST(TDLEN, 0x000FFF80, 0x000FFFFF); + + REG_SET_AND_CHECK(RCTL, 0xFFFFFFFF, 0x00000000); + + before = (adapter->hw.mac_type == e1000_ich8lan ? + 0x06C3B33E : 0x06DFB3FE); + REG_SET_AND_CHECK(RCTL, before, 0x003FFFFB); + REG_SET_AND_CHECK(TCTL, 0xFFFFFFFF, 0x00000000); + + if (adapter->hw.mac_type >= e1000_82543) { + + REG_SET_AND_CHECK(RCTL, before, 0xFFFFFFFF); + REG_PATTERN_TEST(RDBAL, 0xFFFFFFF0, 0xFFFFFFFF); + if (adapter->hw.mac_type != e1000_ich8lan) + REG_PATTERN_TEST(TXCW, 0xC000FFFF, 0x0000FFFF); + REG_PATTERN_TEST(TDBAL, 0xFFFFFFF0, 0xFFFFFFFF); + REG_PATTERN_TEST(TIDV, 0x0000FFFF, 0x0000FFFF); + value = (adapter->hw.mac_type == e1000_ich8lan ? + E1000_RAR_ENTRIES_ICH8LAN : E1000_RAR_ENTRIES); + for (i = 0; i < value; i++) { + REG_PATTERN_TEST(RA + (((i << 1) + 1) << 2), 0x8003FFFF, + 0xFFFFFFFF); + } + + } else { + + REG_SET_AND_CHECK(RCTL, 0xFFFFFFFF, 0x01FFFFFF); + REG_PATTERN_TEST(RDBAL, 0xFFFFF000, 0xFFFFFFFF); + REG_PATTERN_TEST(TXCW, 0x0000FFFF, 0x0000FFFF); + REG_PATTERN_TEST(TDBAL, 0xFFFFF000, 0xFFFFFFFF); + + } + + value = (adapter->hw.mac_type == e1000_ich8lan ? + E1000_MC_TBL_SIZE_ICH8LAN : E1000_MC_TBL_SIZE); + for (i = 0; i < value; i++) + REG_PATTERN_TEST(MTA + (i << 2), 0xFFFFFFFF, 0xFFFFFFFF); + + *data = 0; + return 0; +} + +static int +e1000_eeprom_test(struct e1000_adapter *adapter, uint64_t *data) +{ + uint16_t temp; + uint16_t checksum = 0; + uint16_t i; + + *data = 0; + /* Read and add up the contents of the EEPROM */ + for (i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) { + if ((e1000_read_eeprom(&adapter->hw, i, 1, &temp)) < 0) { + *data = 1; + break; + } + checksum += temp; + } + + /* If Checksum is not Correct return error else test passed */ + if ((checksum != (uint16_t) EEPROM_SUM) && !(*data)) + *data = 2; + + return *data; +} + +static irqreturn_t +e1000_test_intr(int irq, void *data) +{ + struct net_device *netdev = (struct net_device *) data; + struct e1000_adapter *adapter = netdev_priv(netdev); + + adapter->test_icr |= E1000_READ_REG(&adapter->hw, ICR); + + return IRQ_HANDLED; +} + +static int +e1000_intr_test(struct e1000_adapter *adapter, uint64_t *data) +{ + struct net_device *netdev = adapter->netdev; + uint32_t mask, i=0, shared_int = TRUE; + uint32_t irq = adapter->pdev->irq; + + *data = 0; + + /* NOTE: we don't test MSI interrupts here, yet */ + /* Hook up test interrupt handler just for this test */ + if (!request_irq(irq, &e1000_test_intr, IRQF_PROBE_SHARED, netdev->name, + netdev)) + shared_int = FALSE; + else if (request_irq(irq, &e1000_test_intr, IRQF_SHARED, + netdev->name, netdev)) { + *data = 1; + return -1; + } + DPRINTK(HW, INFO, "testing %s interrupt\n", + (shared_int ? "shared" : "unshared")); + + /* Disable all the interrupts */ + E1000_WRITE_REG(&adapter->hw, IMC, 0xFFFFFFFF); + msleep(10); + + /* Test each interrupt */ + for (; i < 10; i++) { + + if (adapter->hw.mac_type == e1000_ich8lan && i == 8) + continue; + + /* Interrupt to test */ + mask = 1 << i; + + if (!shared_int) { + /* Disable the interrupt to be reported in + * the cause register and then force the same + * interrupt and see if one gets posted. If + * an interrupt was posted to the bus, the + * test failed. + */ + adapter->test_icr = 0; + E1000_WRITE_REG(&adapter->hw, IMC, mask); + E1000_WRITE_REG(&adapter->hw, ICS, mask); + msleep(10); + + if (adapter->test_icr & mask) { + *data = 3; + break; + } + } + + /* Enable the interrupt to be reported in + * the cause register and then force the same + * interrupt and see if one gets posted. If + * an interrupt was not posted to the bus, the + * test failed. + */ + adapter->test_icr = 0; + E1000_WRITE_REG(&adapter->hw, IMS, mask); + E1000_WRITE_REG(&adapter->hw, ICS, mask); + msleep(10); + + if (!(adapter->test_icr & mask)) { + *data = 4; + break; + } + + if (!shared_int) { + /* Disable the other interrupts to be reported in + * the cause register and then force the other + * interrupts and see if any get posted. If + * an interrupt was posted to the bus, the + * test failed. + */ + adapter->test_icr = 0; + E1000_WRITE_REG(&adapter->hw, IMC, ~mask & 0x00007FFF); + E1000_WRITE_REG(&adapter->hw, ICS, ~mask & 0x00007FFF); + msleep(10); + + if (adapter->test_icr) { + *data = 5; + break; + } + } + } + + /* Disable all the interrupts */ + E1000_WRITE_REG(&adapter->hw, IMC, 0xFFFFFFFF); + msleep(10); + + /* Unhook test interrupt handler */ + free_irq(irq, netdev); + + return *data; +} + +static void +e1000_free_desc_rings(struct e1000_adapter *adapter) +{ + struct e1000_tx_ring *txdr = &adapter->test_tx_ring; + struct e1000_rx_ring *rxdr = &adapter->test_rx_ring; + struct pci_dev *pdev = adapter->pdev; + int i; + + if (txdr->desc && txdr->buffer_info) { + for (i = 0; i < txdr->count; i++) { + if (txdr->buffer_info[i].dma) + pci_unmap_single(pdev, txdr->buffer_info[i].dma, + txdr->buffer_info[i].length, + PCI_DMA_TODEVICE); + if (txdr->buffer_info[i].skb) + dev_kfree_skb(txdr->buffer_info[i].skb); + } + } + + if (rxdr->desc && rxdr->buffer_info) { + for (i = 0; i < rxdr->count; i++) { + if (rxdr->buffer_info[i].dma) + pci_unmap_single(pdev, rxdr->buffer_info[i].dma, + rxdr->buffer_info[i].length, + PCI_DMA_FROMDEVICE); + if (rxdr->buffer_info[i].skb) + dev_kfree_skb(rxdr->buffer_info[i].skb); + } + } + + if (txdr->desc) { + pci_free_consistent(pdev, txdr->size, txdr->desc, txdr->dma); + txdr->desc = NULL; + } + if (rxdr->desc) { + pci_free_consistent(pdev, rxdr->size, rxdr->desc, rxdr->dma); + rxdr->desc = NULL; + } + + kfree(txdr->buffer_info); + txdr->buffer_info = NULL; + kfree(rxdr->buffer_info); + rxdr->buffer_info = NULL; + + return; +} + +static int +e1000_setup_desc_rings(struct e1000_adapter *adapter) +{ + struct e1000_tx_ring *txdr = &adapter->test_tx_ring; + struct e1000_rx_ring *rxdr = &adapter->test_rx_ring; + struct pci_dev *pdev = adapter->pdev; + uint32_t rctl; + int i, ret_val; + + /* Setup Tx descriptor ring and Tx buffers */ + + if (!txdr->count) + txdr->count = E1000_DEFAULT_TXD; + + if (!(txdr->buffer_info = kcalloc(txdr->count, + sizeof(struct e1000_buffer), + GFP_KERNEL))) { + ret_val = 1; + goto err_nomem; + } + + txdr->size = txdr->count * sizeof(struct e1000_tx_desc); + txdr->size = ALIGN(txdr->size, 4096); + if (!(txdr->desc = pci_alloc_consistent(pdev, txdr->size, + &txdr->dma))) { + ret_val = 2; + goto err_nomem; + } + memset(txdr->desc, 0, txdr->size); + txdr->next_to_use = txdr->next_to_clean = 0; + + E1000_WRITE_REG(&adapter->hw, TDBAL, + ((uint64_t) txdr->dma & 0x00000000FFFFFFFF)); + E1000_WRITE_REG(&adapter->hw, TDBAH, ((uint64_t) txdr->dma >> 32)); + E1000_WRITE_REG(&adapter->hw, TDLEN, + txdr->count * sizeof(struct e1000_tx_desc)); + E1000_WRITE_REG(&adapter->hw, TDH, 0); + E1000_WRITE_REG(&adapter->hw, TDT, 0); + E1000_WRITE_REG(&adapter->hw, TCTL, + E1000_TCTL_PSP | E1000_TCTL_EN | + E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT | + E1000_FDX_COLLISION_DISTANCE << E1000_COLD_SHIFT); + + for (i = 0; i < txdr->count; i++) { + struct e1000_tx_desc *tx_desc = E1000_TX_DESC(*txdr, i); + struct sk_buff *skb; + unsigned int size = 1024; + + if (!(skb = alloc_skb(size, GFP_KERNEL))) { + ret_val = 3; + goto err_nomem; + } + skb_put(skb, size); + txdr->buffer_info[i].skb = skb; + txdr->buffer_info[i].length = skb->len; + txdr->buffer_info[i].dma = + pci_map_single(pdev, skb->data, skb->len, + PCI_DMA_TODEVICE); + tx_desc->buffer_addr = cpu_to_le64(txdr->buffer_info[i].dma); + tx_desc->lower.data = cpu_to_le32(skb->len); + tx_desc->lower.data |= cpu_to_le32(E1000_TXD_CMD_EOP | + E1000_TXD_CMD_IFCS | + E1000_TXD_CMD_RPS); + tx_desc->upper.data = 0; + } + + /* Setup Rx descriptor ring and Rx buffers */ + + if (!rxdr->count) + rxdr->count = E1000_DEFAULT_RXD; + + if (!(rxdr->buffer_info = kcalloc(rxdr->count, + sizeof(struct e1000_buffer), + GFP_KERNEL))) { + ret_val = 4; + goto err_nomem; + } + + rxdr->size = rxdr->count * sizeof(struct e1000_rx_desc); + if (!(rxdr->desc = pci_alloc_consistent(pdev, rxdr->size, &rxdr->dma))) { + ret_val = 5; + goto err_nomem; + } + memset(rxdr->desc, 0, rxdr->size); + rxdr->next_to_use = rxdr->next_to_clean = 0; + + rctl = E1000_READ_REG(&adapter->hw, RCTL); + E1000_WRITE_REG(&adapter->hw, RCTL, rctl & ~E1000_RCTL_EN); + E1000_WRITE_REG(&adapter->hw, RDBAL, + ((uint64_t) rxdr->dma & 0xFFFFFFFF)); + E1000_WRITE_REG(&adapter->hw, RDBAH, ((uint64_t) rxdr->dma >> 32)); + E1000_WRITE_REG(&adapter->hw, RDLEN, rxdr->size); + E1000_WRITE_REG(&adapter->hw, RDH, 0); + E1000_WRITE_REG(&adapter->hw, RDT, 0); + rctl = E1000_RCTL_EN | E1000_RCTL_BAM | E1000_RCTL_SZ_2048 | + E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF | + (adapter->hw.mc_filter_type << E1000_RCTL_MO_SHIFT); + E1000_WRITE_REG(&adapter->hw, RCTL, rctl); + + for (i = 0; i < rxdr->count; i++) { + struct e1000_rx_desc *rx_desc = E1000_RX_DESC(*rxdr, i); + struct sk_buff *skb; + + if (!(skb = alloc_skb(E1000_RXBUFFER_2048 + NET_IP_ALIGN, + GFP_KERNEL))) { + ret_val = 6; + goto err_nomem; + } + skb_reserve(skb, NET_IP_ALIGN); + rxdr->buffer_info[i].skb = skb; + rxdr->buffer_info[i].length = E1000_RXBUFFER_2048; + rxdr->buffer_info[i].dma = + pci_map_single(pdev, skb->data, E1000_RXBUFFER_2048, + PCI_DMA_FROMDEVICE); + rx_desc->buffer_addr = cpu_to_le64(rxdr->buffer_info[i].dma); + memset(skb->data, 0x00, skb->len); + } + + return 0; + +err_nomem: + e1000_free_desc_rings(adapter); + return ret_val; +} + +static void +e1000_phy_disable_receiver(struct e1000_adapter *adapter) +{ + /* Write out to PHY registers 29 and 30 to disable the Receiver. */ + e1000_write_phy_reg(&adapter->hw, 29, 0x001F); + e1000_write_phy_reg(&adapter->hw, 30, 0x8FFC); + e1000_write_phy_reg(&adapter->hw, 29, 0x001A); + e1000_write_phy_reg(&adapter->hw, 30, 0x8FF0); +} + +static void +e1000_phy_reset_clk_and_crs(struct e1000_adapter *adapter) +{ + uint16_t phy_reg; + + /* Because we reset the PHY above, we need to re-force TX_CLK in the + * Extended PHY Specific Control Register to 25MHz clock. This + * value defaults back to a 2.5MHz clock when the PHY is reset. + */ + e1000_read_phy_reg(&adapter->hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_reg); + phy_reg |= M88E1000_EPSCR_TX_CLK_25; + e1000_write_phy_reg(&adapter->hw, + M88E1000_EXT_PHY_SPEC_CTRL, phy_reg); + + /* In addition, because of the s/w reset above, we need to enable + * CRS on TX. This must be set for both full and half duplex + * operation. + */ + e1000_read_phy_reg(&adapter->hw, M88E1000_PHY_SPEC_CTRL, &phy_reg); + phy_reg |= M88E1000_PSCR_ASSERT_CRS_ON_TX; + e1000_write_phy_reg(&adapter->hw, + M88E1000_PHY_SPEC_CTRL, phy_reg); +} + +static int +e1000_nonintegrated_phy_loopback(struct e1000_adapter *adapter) +{ + uint32_t ctrl_reg; + uint16_t phy_reg; + + /* Setup the Device Control Register for PHY loopback test. */ + + ctrl_reg = E1000_READ_REG(&adapter->hw, CTRL); + ctrl_reg |= (E1000_CTRL_ILOS | /* Invert Loss-Of-Signal */ + E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */ + E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */ + E1000_CTRL_SPD_1000 | /* Force Speed to 1000 */ + E1000_CTRL_FD); /* Force Duplex to FULL */ + + E1000_WRITE_REG(&adapter->hw, CTRL, ctrl_reg); + + /* Read the PHY Specific Control Register (0x10) */ + e1000_read_phy_reg(&adapter->hw, M88E1000_PHY_SPEC_CTRL, &phy_reg); + + /* Clear Auto-Crossover bits in PHY Specific Control Register + * (bits 6:5). + */ + phy_reg &= ~M88E1000_PSCR_AUTO_X_MODE; + e1000_write_phy_reg(&adapter->hw, M88E1000_PHY_SPEC_CTRL, phy_reg); + + /* Perform software reset on the PHY */ + e1000_phy_reset(&adapter->hw); + + /* Have to setup TX_CLK and TX_CRS after software reset */ + e1000_phy_reset_clk_and_crs(adapter); + + e1000_write_phy_reg(&adapter->hw, PHY_CTRL, 0x8100); + + /* Wait for reset to complete. */ + udelay(500); + + /* Have to setup TX_CLK and TX_CRS after software reset */ + e1000_phy_reset_clk_and_crs(adapter); + + /* Write out to PHY registers 29 and 30 to disable the Receiver. */ + e1000_phy_disable_receiver(adapter); + + /* Set the loopback bit in the PHY control register. */ + e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &phy_reg); + phy_reg |= MII_CR_LOOPBACK; + e1000_write_phy_reg(&adapter->hw, PHY_CTRL, phy_reg); + + /* Setup TX_CLK and TX_CRS one more time. */ + e1000_phy_reset_clk_and_crs(adapter); + + /* Check Phy Configuration */ + e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &phy_reg); + if (phy_reg != 0x4100) + return 9; + + e1000_read_phy_reg(&adapter->hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_reg); + if (phy_reg != 0x0070) + return 10; + + e1000_read_phy_reg(&adapter->hw, 29, &phy_reg); + if (phy_reg != 0x001A) + return 11; + + return 0; +} + +static int +e1000_integrated_phy_loopback(struct e1000_adapter *adapter) +{ + uint32_t ctrl_reg = 0; + uint32_t stat_reg = 0; + + adapter->hw.autoneg = FALSE; + + if (adapter->hw.phy_type == e1000_phy_m88) { + /* Auto-MDI/MDIX Off */ + e1000_write_phy_reg(&adapter->hw, + M88E1000_PHY_SPEC_CTRL, 0x0808); + /* reset to update Auto-MDI/MDIX */ + e1000_write_phy_reg(&adapter->hw, PHY_CTRL, 0x9140); + /* autoneg off */ + e1000_write_phy_reg(&adapter->hw, PHY_CTRL, 0x8140); + } else if (adapter->hw.phy_type == e1000_phy_gg82563) + e1000_write_phy_reg(&adapter->hw, + GG82563_PHY_KMRN_MODE_CTRL, + 0x1CC); + + ctrl_reg = E1000_READ_REG(&adapter->hw, CTRL); + + if (adapter->hw.phy_type == e1000_phy_ife) { + /* force 100, set loopback */ + e1000_write_phy_reg(&adapter->hw, PHY_CTRL, 0x6100); + + /* Now set up the MAC to the same speed/duplex as the PHY. */ + ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */ + ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */ + E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */ + E1000_CTRL_SPD_100 |/* Force Speed to 100 */ + E1000_CTRL_FD); /* Force Duplex to FULL */ + } else { + /* force 1000, set loopback */ + e1000_write_phy_reg(&adapter->hw, PHY_CTRL, 0x4140); + + /* Now set up the MAC to the same speed/duplex as the PHY. */ + ctrl_reg = E1000_READ_REG(&adapter->hw, CTRL); + ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */ + ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */ + E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */ + E1000_CTRL_SPD_1000 |/* Force Speed to 1000 */ + E1000_CTRL_FD); /* Force Duplex to FULL */ + } + + if (adapter->hw.media_type == e1000_media_type_copper && + adapter->hw.phy_type == e1000_phy_m88) + ctrl_reg |= E1000_CTRL_ILOS; /* Invert Loss of Signal */ + else { + /* Set the ILOS bit on the fiber Nic is half + * duplex link is detected. */ + stat_reg = E1000_READ_REG(&adapter->hw, STATUS); + if ((stat_reg & E1000_STATUS_FD) == 0) + ctrl_reg |= (E1000_CTRL_ILOS | E1000_CTRL_SLU); + } + + E1000_WRITE_REG(&adapter->hw, CTRL, ctrl_reg); + + /* Disable the receiver on the PHY so when a cable is plugged in, the + * PHY does not begin to autoneg when a cable is reconnected to the NIC. + */ + if (adapter->hw.phy_type == e1000_phy_m88) + e1000_phy_disable_receiver(adapter); + + udelay(500); + + return 0; +} + +static int +e1000_set_phy_loopback(struct e1000_adapter *adapter) +{ + uint16_t phy_reg = 0; + uint16_t count = 0; + + switch (adapter->hw.mac_type) { + case e1000_82543: + if (adapter->hw.media_type == e1000_media_type_copper) { + /* Attempt to setup Loopback mode on Non-integrated PHY. + * Some PHY registers get corrupted at random, so + * attempt this 10 times. + */ + while (e1000_nonintegrated_phy_loopback(adapter) && + count++ < 10); + if (count < 11) + return 0; + } + break; + + case e1000_82544: + case e1000_82540: + case e1000_82545: + case e1000_82545_rev_3: + case e1000_82546: + case e1000_82546_rev_3: + case e1000_82541: + case e1000_82541_rev_2: + case e1000_82547: + case e1000_82547_rev_2: + case e1000_82571: + case e1000_82572: + case e1000_82573: + case e1000_80003es2lan: + case e1000_ich8lan: + return e1000_integrated_phy_loopback(adapter); + break; + + default: + /* Default PHY loopback work is to read the MII + * control register and assert bit 14 (loopback mode). + */ + e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &phy_reg); + phy_reg |= MII_CR_LOOPBACK; + e1000_write_phy_reg(&adapter->hw, PHY_CTRL, phy_reg); + return 0; + break; + } + + return 8; +} + +static int +e1000_setup_loopback_test(struct e1000_adapter *adapter) +{ + struct e1000_hw *hw = &adapter->hw; + uint32_t rctl; + + if (hw->media_type == e1000_media_type_fiber || + hw->media_type == e1000_media_type_internal_serdes) { + switch (hw->mac_type) { + case e1000_82545: + case e1000_82546: + case e1000_82545_rev_3: + case e1000_82546_rev_3: + return e1000_set_phy_loopback(adapter); + break; + case e1000_82571: + case e1000_82572: +#define E1000_SERDES_LB_ON 0x410 + e1000_set_phy_loopback(adapter); + E1000_WRITE_REG(hw, SCTL, E1000_SERDES_LB_ON); + msleep(10); + return 0; + break; + default: + rctl = E1000_READ_REG(hw, RCTL); + rctl |= E1000_RCTL_LBM_TCVR; + E1000_WRITE_REG(hw, RCTL, rctl); + return 0; + } + } else if (hw->media_type == e1000_media_type_copper) + return e1000_set_phy_loopback(adapter); + + return 7; +} + +static void +e1000_loopback_cleanup(struct e1000_adapter *adapter) +{ + struct e1000_hw *hw = &adapter->hw; + uint32_t rctl; + uint16_t phy_reg; + + rctl = E1000_READ_REG(hw, RCTL); + rctl &= ~(E1000_RCTL_LBM_TCVR | E1000_RCTL_LBM_MAC); + E1000_WRITE_REG(hw, RCTL, rctl); + + switch (hw->mac_type) { + case e1000_82571: + case e1000_82572: + if (hw->media_type == e1000_media_type_fiber || + hw->media_type == e1000_media_type_internal_serdes) { +#define E1000_SERDES_LB_OFF 0x400 + E1000_WRITE_REG(hw, SCTL, E1000_SERDES_LB_OFF); + msleep(10); + break; + } + /* Fall Through */ + case e1000_82545: + case e1000_82546: + case e1000_82545_rev_3: + case e1000_82546_rev_3: + default: + hw->autoneg = TRUE; + if (hw->phy_type == e1000_phy_gg82563) + e1000_write_phy_reg(hw, + GG82563_PHY_KMRN_MODE_CTRL, + 0x180); + e1000_read_phy_reg(hw, PHY_CTRL, &phy_reg); + if (phy_reg & MII_CR_LOOPBACK) { + phy_reg &= ~MII_CR_LOOPBACK; + e1000_write_phy_reg(hw, PHY_CTRL, phy_reg); + e1000_phy_reset(hw); + } + break; + } +} + +static void +e1000_create_lbtest_frame(struct sk_buff *skb, unsigned int frame_size) +{ + memset(skb->data, 0xFF, frame_size); + frame_size &= ~1; + memset(&skb->data[frame_size / 2], 0xAA, frame_size / 2 - 1); + memset(&skb->data[frame_size / 2 + 10], 0xBE, 1); + memset(&skb->data[frame_size / 2 + 12], 0xAF, 1); +} + +static int +e1000_check_lbtest_frame(struct sk_buff *skb, unsigned int frame_size) +{ + frame_size &= ~1; + if (*(skb->data + 3) == 0xFF) { + if ((*(skb->data + frame_size / 2 + 10) == 0xBE) && + (*(skb->data + frame_size / 2 + 12) == 0xAF)) { + return 0; + } + } + return 13; +} + +static int +e1000_run_loopback_test(struct e1000_adapter *adapter) +{ + struct e1000_tx_ring *txdr = &adapter->test_tx_ring; + struct e1000_rx_ring *rxdr = &adapter->test_rx_ring; + struct pci_dev *pdev = adapter->pdev; + int i, j, k, l, lc, good_cnt, ret_val=0; + unsigned long time; + + E1000_WRITE_REG(&adapter->hw, RDT, rxdr->count - 1); + + /* Calculate the loop count based on the largest descriptor ring + * The idea is to wrap the largest ring a number of times using 64 + * send/receive pairs during each loop + */ + + if (rxdr->count <= txdr->count) + lc = ((txdr->count / 64) * 2) + 1; + else + lc = ((rxdr->count / 64) * 2) + 1; + + k = l = 0; + for (j = 0; j <= lc; j++) { /* loop count loop */ + for (i = 0; i < 64; i++) { /* send the packets */ + e1000_create_lbtest_frame(txdr->buffer_info[i].skb, + 1024); + pci_dma_sync_single_for_device(pdev, + txdr->buffer_info[k].dma, + txdr->buffer_info[k].length, + PCI_DMA_TODEVICE); + if (unlikely(++k == txdr->count)) k = 0; + } + E1000_WRITE_REG(&adapter->hw, TDT, k); + msleep(200); + time = jiffies; /* set the start time for the receive */ + good_cnt = 0; + do { /* receive the sent packets */ + pci_dma_sync_single_for_cpu(pdev, + rxdr->buffer_info[l].dma, + rxdr->buffer_info[l].length, + PCI_DMA_FROMDEVICE); + + ret_val = e1000_check_lbtest_frame( + rxdr->buffer_info[l].skb, + 1024); + if (!ret_val) + good_cnt++; + if (unlikely(++l == rxdr->count)) l = 0; + /* time + 20 msecs (200 msecs on 2.4) is more than + * enough time to complete the receives, if it's + * exceeded, break and error off + */ + } while (good_cnt < 64 && jiffies < (time + 20)); + if (good_cnt != 64) { + ret_val = 13; /* ret_val is the same as mis-compare */ + break; + } + if (jiffies >= (time + 2)) { + ret_val = 14; /* error code for time out error */ + break; + } + } /* end loop count loop */ + return ret_val; +} + +static int +e1000_loopback_test(struct e1000_adapter *adapter, uint64_t *data) +{ + /* PHY loopback cannot be performed if SoL/IDER + * sessions are active */ + if (e1000_check_phy_reset_block(&adapter->hw)) { + DPRINTK(DRV, ERR, "Cannot do PHY loopback test " + "when SoL/IDER is active.\n"); + *data = 0; + goto out; + } + + if ((*data = e1000_setup_desc_rings(adapter))) + goto out; + if ((*data = e1000_setup_loopback_test(adapter))) + goto err_loopback; + *data = e1000_run_loopback_test(adapter); + e1000_loopback_cleanup(adapter); + +err_loopback: + e1000_free_desc_rings(adapter); +out: + return *data; +} + +static int +e1000_link_test(struct e1000_adapter *adapter, uint64_t *data) +{ + *data = 0; + if (adapter->hw.media_type == e1000_media_type_internal_serdes) { + int i = 0; + adapter->hw.serdes_link_down = TRUE; + + /* On some blade server designs, link establishment + * could take as long as 2-3 minutes */ + do { + e1000_check_for_link(&adapter->hw); + if (adapter->hw.serdes_link_down == FALSE) + return *data; + msleep(20); + } while (i++ < 3750); + + *data = 1; + } else { + e1000_check_for_link(&adapter->hw); + if (adapter->hw.autoneg) /* if auto_neg is set wait for it */ + msleep(4000); + + if (!(E1000_READ_REG(&adapter->hw, STATUS) & E1000_STATUS_LU)) { + *data = 1; + } + } + return *data; +} + +static int +e1000_get_sset_count(struct net_device *netdev, int sset) +{ + switch (sset) { + case ETH_SS_TEST: + return E1000_TEST_LEN; + case ETH_SS_STATS: + return E1000_STATS_LEN; + default: + return -EOPNOTSUPP; + } +} + +static void +e1000_diag_test(struct net_device *netdev, + struct ethtool_test *eth_test, uint64_t *data) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + boolean_t if_running; + + if (adapter->ecdev) + return; + + if_running = netif_running(netdev); + + set_bit(__E1000_TESTING, &adapter->flags); + if (eth_test->flags == ETH_TEST_FL_OFFLINE) { + /* Offline tests */ + + /* save speed, duplex, autoneg settings */ + uint16_t autoneg_advertised = adapter->hw.autoneg_advertised; + uint8_t forced_speed_duplex = adapter->hw.forced_speed_duplex; + uint8_t autoneg = adapter->hw.autoneg; + + DPRINTK(HW, INFO, "offline testing starting\n"); + + /* Link test performed before hardware reset so autoneg doesn't + * interfere with test result */ + if (e1000_link_test(adapter, &data[4])) + eth_test->flags |= ETH_TEST_FL_FAILED; + + if (if_running) + /* indicate we're in test mode */ + dev_close(netdev); + else + e1000_reset(adapter); + + if (e1000_reg_test(adapter, &data[0])) + eth_test->flags |= ETH_TEST_FL_FAILED; + + e1000_reset(adapter); + if (e1000_eeprom_test(adapter, &data[1])) + eth_test->flags |= ETH_TEST_FL_FAILED; + + e1000_reset(adapter); + if (e1000_intr_test(adapter, &data[2])) + eth_test->flags |= ETH_TEST_FL_FAILED; + + e1000_reset(adapter); + /* make sure the phy is powered up */ + e1000_power_up_phy(adapter); + if (e1000_loopback_test(adapter, &data[3])) + eth_test->flags |= ETH_TEST_FL_FAILED; + + /* restore speed, duplex, autoneg settings */ + adapter->hw.autoneg_advertised = autoneg_advertised; + adapter->hw.forced_speed_duplex = forced_speed_duplex; + adapter->hw.autoneg = autoneg; + + e1000_reset(adapter); + clear_bit(__E1000_TESTING, &adapter->flags); + if (if_running) + dev_open(netdev); + } else { + DPRINTK(HW, INFO, "online testing starting\n"); + /* Online tests */ + if (e1000_link_test(adapter, &data[4])) + eth_test->flags |= ETH_TEST_FL_FAILED; + + /* Online tests aren't run; pass by default */ + data[0] = 0; + data[1] = 0; + data[2] = 0; + data[3] = 0; + + clear_bit(__E1000_TESTING, &adapter->flags); + } + msleep_interruptible(4 * 1000); +} + +static int e1000_wol_exclusion(struct e1000_adapter *adapter, struct ethtool_wolinfo *wol) +{ + struct e1000_hw *hw = &adapter->hw; + int retval = 1; /* fail by default */ + + switch (hw->device_id) { + case E1000_DEV_ID_82542: + case E1000_DEV_ID_82543GC_FIBER: + case E1000_DEV_ID_82543GC_COPPER: + case E1000_DEV_ID_82544EI_FIBER: + case E1000_DEV_ID_82546EB_QUAD_COPPER: + case E1000_DEV_ID_82545EM_FIBER: + case E1000_DEV_ID_82545EM_COPPER: + case E1000_DEV_ID_82546GB_QUAD_COPPER: + case E1000_DEV_ID_82546GB_PCIE: + case E1000_DEV_ID_82571EB_SERDES_QUAD: + /* these don't support WoL at all */ + wol->supported = 0; + break; + case E1000_DEV_ID_82546EB_FIBER: + case E1000_DEV_ID_82546GB_FIBER: + case E1000_DEV_ID_82571EB_FIBER: + case E1000_DEV_ID_82571EB_SERDES: + case E1000_DEV_ID_82571EB_COPPER: + /* Wake events not supported on port B */ + if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1) { + wol->supported = 0; + break; + } + /* return success for non excluded adapter ports */ + retval = 0; + break; + case E1000_DEV_ID_82571EB_QUAD_COPPER: + case E1000_DEV_ID_82571EB_QUAD_FIBER: + case E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE: + case E1000_DEV_ID_82571PT_QUAD_COPPER: + case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3: + /* quad port adapters only support WoL on port A */ + if (!adapter->quad_port_a) { + wol->supported = 0; + break; + } + /* return success for non excluded adapter ports */ + retval = 0; + break; + default: + /* dual port cards only support WoL on port A from now on + * unless it was enabled in the eeprom for port B + * so exclude FUNC_1 ports from having WoL enabled */ + if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1 && + !adapter->eeprom_wol) { + wol->supported = 0; + break; + } + + retval = 0; + } + + return retval; +} + +static void +e1000_get_wol(struct net_device *netdev, struct ethtool_wolinfo *wol) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + + wol->supported = WAKE_UCAST | WAKE_MCAST | + WAKE_BCAST | WAKE_MAGIC; + wol->wolopts = 0; + + /* this function will set ->supported = 0 and return 1 if wol is not + * supported by this hardware */ + if (e1000_wol_exclusion(adapter, wol)) + return; + + /* apply any specific unsupported masks here */ + switch (adapter->hw.device_id) { + case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3: + /* KSP3 does not suppport UCAST wake-ups */ + wol->supported &= ~WAKE_UCAST; + + if (adapter->wol & E1000_WUFC_EX) + DPRINTK(DRV, ERR, "Interface does not support " + "directed (unicast) frame wake-up packets\n"); + break; + default: + break; + } + + if (adapter->wol & E1000_WUFC_EX) + wol->wolopts |= WAKE_UCAST; + if (adapter->wol & E1000_WUFC_MC) + wol->wolopts |= WAKE_MCAST; + if (adapter->wol & E1000_WUFC_BC) + wol->wolopts |= WAKE_BCAST; + if (adapter->wol & E1000_WUFC_MAG) + wol->wolopts |= WAKE_MAGIC; + + return; +} + +static int +e1000_set_wol(struct net_device *netdev, struct ethtool_wolinfo *wol) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + struct e1000_hw *hw = &adapter->hw; + + if (wol->wolopts & (WAKE_PHY | WAKE_ARP | WAKE_MAGICSECURE)) + return -EOPNOTSUPP; + + if (e1000_wol_exclusion(adapter, wol)) + return wol->wolopts ? -EOPNOTSUPP : 0; + + switch (hw->device_id) { + case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3: + if (wol->wolopts & WAKE_UCAST) { + DPRINTK(DRV, ERR, "Interface does not support " + "directed (unicast) frame wake-up packets\n"); + return -EOPNOTSUPP; + } + break; + default: + break; + } + + /* these settings will always override what we currently have */ + adapter->wol = 0; + + if (wol->wolopts & WAKE_UCAST) + adapter->wol |= E1000_WUFC_EX; + if (wol->wolopts & WAKE_MCAST) + adapter->wol |= E1000_WUFC_MC; + if (wol->wolopts & WAKE_BCAST) + adapter->wol |= E1000_WUFC_BC; + if (wol->wolopts & WAKE_MAGIC) + adapter->wol |= E1000_WUFC_MAG; + + return 0; +} + +/* toggle LED 4 times per second = 2 "blinks" per second */ +#define E1000_ID_INTERVAL (HZ/4) + +/* bit defines for adapter->led_status */ +#define E1000_LED_ON 0 + +static void +e1000_led_blink_callback(unsigned long data) +{ + struct e1000_adapter *adapter = (struct e1000_adapter *) data; + + if (test_and_change_bit(E1000_LED_ON, &adapter->led_status)) + e1000_led_off(&adapter->hw); + else + e1000_led_on(&adapter->hw); + + mod_timer(&adapter->blink_timer, jiffies + E1000_ID_INTERVAL); +} + +static int +e1000_phys_id(struct net_device *netdev, uint32_t data) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + + if (!data) + data = INT_MAX; + + if (adapter->hw.mac_type < e1000_82571) { + if (!adapter->blink_timer.function) { + init_timer(&adapter->blink_timer); + adapter->blink_timer.function = e1000_led_blink_callback; + adapter->blink_timer.data = (unsigned long) adapter; + } + e1000_setup_led(&adapter->hw); + mod_timer(&adapter->blink_timer, jiffies); + msleep_interruptible(data * 1000); + del_timer_sync(&adapter->blink_timer); + } else if (adapter->hw.phy_type == e1000_phy_ife) { + if (!adapter->blink_timer.function) { + init_timer(&adapter->blink_timer); + adapter->blink_timer.function = e1000_led_blink_callback; + adapter->blink_timer.data = (unsigned long) adapter; + } + mod_timer(&adapter->blink_timer, jiffies); + msleep_interruptible(data * 1000); + del_timer_sync(&adapter->blink_timer); + e1000_write_phy_reg(&(adapter->hw), IFE_PHY_SPECIAL_CONTROL_LED, 0); + } else { + e1000_blink_led_start(&adapter->hw); + msleep_interruptible(data * 1000); + } + + e1000_led_off(&adapter->hw); + clear_bit(E1000_LED_ON, &adapter->led_status); + e1000_cleanup_led(&adapter->hw); + + return 0; +} + +static int +e1000_nway_reset(struct net_device *netdev) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + + if (adapter->ecdev) + return -EBUSY; + + if (netif_running(netdev)) + e1000_reinit_locked(adapter); + return 0; +} + +static void +e1000_get_ethtool_stats(struct net_device *netdev, + struct ethtool_stats *stats, uint64_t *data) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + int i; + + e1000_update_stats(adapter); + for (i = 0; i < E1000_GLOBAL_STATS_LEN; i++) { + char *p = (char *)adapter+e1000_gstrings_stats[i].stat_offset; + data[i] = (e1000_gstrings_stats[i].sizeof_stat == + sizeof(uint64_t)) ? *(uint64_t *)p : *(uint32_t *)p; + } +/* BUG_ON(i != E1000_STATS_LEN); */ +} + +static void +e1000_get_strings(struct net_device *netdev, uint32_t stringset, uint8_t *data) +{ + uint8_t *p = data; + int i; + + switch (stringset) { + case ETH_SS_TEST: + memcpy(data, *e1000_gstrings_test, + sizeof(e1000_gstrings_test)); + break; + case ETH_SS_STATS: + for (i = 0; i < E1000_GLOBAL_STATS_LEN; i++) { + memcpy(p, e1000_gstrings_stats[i].stat_string, + ETH_GSTRING_LEN); + p += ETH_GSTRING_LEN; + } +/* BUG_ON(p - data != E1000_STATS_LEN * ETH_GSTRING_LEN); */ + break; + } +} + +static const struct ethtool_ops e1000_ethtool_ops = { + .get_settings = e1000_get_settings, + .set_settings = e1000_set_settings, + .get_drvinfo = e1000_get_drvinfo, + .get_regs_len = e1000_get_regs_len, + .get_regs = e1000_get_regs, + .get_wol = e1000_get_wol, + .set_wol = e1000_set_wol, + .get_msglevel = e1000_get_msglevel, + .set_msglevel = e1000_set_msglevel, + .nway_reset = e1000_nway_reset, + .get_link = ethtool_op_get_link, + .get_eeprom_len = e1000_get_eeprom_len, + .get_eeprom = e1000_get_eeprom, + .set_eeprom = e1000_set_eeprom, + .get_ringparam = e1000_get_ringparam, + .set_ringparam = e1000_set_ringparam, + .get_pauseparam = e1000_get_pauseparam, + .set_pauseparam = e1000_set_pauseparam, + .get_rx_csum = e1000_get_rx_csum, + .set_rx_csum = e1000_set_rx_csum, + .get_tx_csum = e1000_get_tx_csum, + .set_tx_csum = e1000_set_tx_csum, + .set_sg = ethtool_op_set_sg, + .set_tso = e1000_set_tso, + .self_test = e1000_diag_test, + .get_strings = e1000_get_strings, + .phys_id = e1000_phys_id, + .get_ethtool_stats = e1000_get_ethtool_stats, + .get_sset_count = e1000_get_sset_count, +}; + +void e1000_set_ethtool_ops(struct net_device *netdev) +{ + SET_ETHTOOL_OPS(netdev, &e1000_ethtool_ops); +} diff -Nur ethercat-1.4.0/devices/e1000/e1000_ethtool-2.6.32-orig.c ethercat-1.4.0.patched//devices/e1000/e1000_ethtool-2.6.32-orig.c --- ethercat-1.4.0/devices/e1000/e1000_ethtool-2.6.32-orig.c 1970-01-01 01:00:00.000000000 +0100 +++ ethercat-1.4.0.patched//devices/e1000/e1000_ethtool-2.6.32-orig.c 2011-11-18 12:19:07.282817424 +0100 @@ -0,0 +1,1974 @@ +/******************************************************************************* + + Intel PRO/1000 Linux driver + Copyright(c) 1999 - 2006 Intel Corporation. + + This program is free software; you can redistribute it and/or modify it + under the terms and conditions of the GNU General Public License, + version 2, as published by the Free Software Foundation. + + This program is distributed in the hope it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., + 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. + + The full GNU General Public License is included in this distribution in + the file called "COPYING". + + Contact Information: + Linux NICS + e1000-devel Mailing List + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + +*******************************************************************************/ + +/* ethtool support for e1000 */ + +#include "e1000.h" + +#include + +extern int e1000_up(struct e1000_adapter *adapter); +extern void e1000_down(struct e1000_adapter *adapter); +extern void e1000_reinit_locked(struct e1000_adapter *adapter); +extern void e1000_reset(struct e1000_adapter *adapter); +extern int e1000_set_spd_dplx(struct e1000_adapter *adapter, uint16_t spddplx); +extern int e1000_setup_all_rx_resources(struct e1000_adapter *adapter); +extern int e1000_setup_all_tx_resources(struct e1000_adapter *adapter); +extern void e1000_free_all_rx_resources(struct e1000_adapter *adapter); +extern void e1000_free_all_tx_resources(struct e1000_adapter *adapter); +extern void e1000_update_stats(struct e1000_adapter *adapter); + + +struct e1000_stats { + char stat_string[ETH_GSTRING_LEN]; + int sizeof_stat; + int stat_offset; +}; + +#define E1000_STAT(m) sizeof(((struct e1000_adapter *)0)->m), \ + offsetof(struct e1000_adapter, m) +static const struct e1000_stats e1000_gstrings_stats[] = { + { "rx_packets", E1000_STAT(stats.gprc) }, + { "tx_packets", E1000_STAT(stats.gptc) }, + { "rx_bytes", E1000_STAT(stats.gorcl) }, + { "tx_bytes", E1000_STAT(stats.gotcl) }, + { "rx_broadcast", E1000_STAT(stats.bprc) }, + { "tx_broadcast", E1000_STAT(stats.bptc) }, + { "rx_multicast", E1000_STAT(stats.mprc) }, + { "tx_multicast", E1000_STAT(stats.mptc) }, + { "rx_errors", E1000_STAT(stats.rxerrc) }, + { "tx_errors", E1000_STAT(stats.txerrc) }, + { "tx_dropped", E1000_STAT(net_stats.tx_dropped) }, + { "multicast", E1000_STAT(stats.mprc) }, + { "collisions", E1000_STAT(stats.colc) }, + { "rx_length_errors", E1000_STAT(stats.rlerrc) }, + { "rx_over_errors", E1000_STAT(net_stats.rx_over_errors) }, + { "rx_crc_errors", E1000_STAT(stats.crcerrs) }, + { "rx_frame_errors", E1000_STAT(net_stats.rx_frame_errors) }, + { "rx_no_buffer_count", E1000_STAT(stats.rnbc) }, + { "rx_missed_errors", E1000_STAT(stats.mpc) }, + { "tx_aborted_errors", E1000_STAT(stats.ecol) }, + { "tx_carrier_errors", E1000_STAT(stats.tncrs) }, + { "tx_fifo_errors", E1000_STAT(net_stats.tx_fifo_errors) }, + { "tx_heartbeat_errors", E1000_STAT(net_stats.tx_heartbeat_errors) }, + { "tx_window_errors", E1000_STAT(stats.latecol) }, + { "tx_abort_late_coll", E1000_STAT(stats.latecol) }, + { "tx_deferred_ok", E1000_STAT(stats.dc) }, + { "tx_single_coll_ok", E1000_STAT(stats.scc) }, + { "tx_multi_coll_ok", E1000_STAT(stats.mcc) }, + { "tx_timeout_count", E1000_STAT(tx_timeout_count) }, + { "tx_restart_queue", E1000_STAT(restart_queue) }, + { "rx_long_length_errors", E1000_STAT(stats.roc) }, + { "rx_short_length_errors", E1000_STAT(stats.ruc) }, + { "rx_align_errors", E1000_STAT(stats.algnerrc) }, + { "tx_tcp_seg_good", E1000_STAT(stats.tsctc) }, + { "tx_tcp_seg_failed", E1000_STAT(stats.tsctfc) }, + { "rx_flow_control_xon", E1000_STAT(stats.xonrxc) }, + { "rx_flow_control_xoff", E1000_STAT(stats.xoffrxc) }, + { "tx_flow_control_xon", E1000_STAT(stats.xontxc) }, + { "tx_flow_control_xoff", E1000_STAT(stats.xofftxc) }, + { "rx_long_byte_count", E1000_STAT(stats.gorcl) }, + { "rx_csum_offload_good", E1000_STAT(hw_csum_good) }, + { "rx_csum_offload_errors", E1000_STAT(hw_csum_err) }, + { "rx_header_split", E1000_STAT(rx_hdr_split) }, + { "alloc_rx_buff_failed", E1000_STAT(alloc_rx_buff_failed) }, + { "tx_smbus", E1000_STAT(stats.mgptc) }, + { "rx_smbus", E1000_STAT(stats.mgprc) }, + { "dropped_smbus", E1000_STAT(stats.mgpdc) }, +}; + +#define E1000_QUEUE_STATS_LEN 0 +#define E1000_GLOBAL_STATS_LEN ARRAY_SIZE(e1000_gstrings_stats) +#define E1000_STATS_LEN (E1000_GLOBAL_STATS_LEN + E1000_QUEUE_STATS_LEN) +static const char e1000_gstrings_test[][ETH_GSTRING_LEN] = { + "Register test (offline)", "Eeprom test (offline)", + "Interrupt test (offline)", "Loopback test (offline)", + "Link test (on/offline)" +}; +#define E1000_TEST_LEN sizeof(e1000_gstrings_test) / ETH_GSTRING_LEN + +static int +e1000_get_settings(struct net_device *netdev, struct ethtool_cmd *ecmd) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + struct e1000_hw *hw = &adapter->hw; + + if (hw->media_type == e1000_media_type_copper) { + + ecmd->supported = (SUPPORTED_10baseT_Half | + SUPPORTED_10baseT_Full | + SUPPORTED_100baseT_Half | + SUPPORTED_100baseT_Full | + SUPPORTED_1000baseT_Full| + SUPPORTED_Autoneg | + SUPPORTED_TP); + if (hw->phy_type == e1000_phy_ife) + ecmd->supported &= ~SUPPORTED_1000baseT_Full; + ecmd->advertising = ADVERTISED_TP; + + if (hw->autoneg == 1) { + ecmd->advertising |= ADVERTISED_Autoneg; + /* the e1000 autoneg seems to match ethtool nicely */ + ecmd->advertising |= hw->autoneg_advertised; + } + + ecmd->port = PORT_TP; + ecmd->phy_address = hw->phy_addr; + + if (hw->mac_type == e1000_82543) + ecmd->transceiver = XCVR_EXTERNAL; + else + ecmd->transceiver = XCVR_INTERNAL; + + } else { + ecmd->supported = (SUPPORTED_1000baseT_Full | + SUPPORTED_FIBRE | + SUPPORTED_Autoneg); + + ecmd->advertising = (ADVERTISED_1000baseT_Full | + ADVERTISED_FIBRE | + ADVERTISED_Autoneg); + + ecmd->port = PORT_FIBRE; + + if (hw->mac_type >= e1000_82545) + ecmd->transceiver = XCVR_INTERNAL; + else + ecmd->transceiver = XCVR_EXTERNAL; + } + + if (E1000_READ_REG(&adapter->hw, STATUS) & E1000_STATUS_LU) { + + e1000_get_speed_and_duplex(hw, &adapter->link_speed, + &adapter->link_duplex); + ecmd->speed = adapter->link_speed; + + /* unfortunatly FULL_DUPLEX != DUPLEX_FULL + * and HALF_DUPLEX != DUPLEX_HALF */ + + if (adapter->link_duplex == FULL_DUPLEX) + ecmd->duplex = DUPLEX_FULL; + else + ecmd->duplex = DUPLEX_HALF; + } else { + ecmd->speed = -1; + ecmd->duplex = -1; + } + + ecmd->autoneg = ((hw->media_type == e1000_media_type_fiber) || + hw->autoneg) ? AUTONEG_ENABLE : AUTONEG_DISABLE; + return 0; +} + +static int +e1000_set_settings(struct net_device *netdev, struct ethtool_cmd *ecmd) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + struct e1000_hw *hw = &adapter->hw; + + /* When SoL/IDER sessions are active, autoneg/speed/duplex + * cannot be changed */ + if (e1000_check_phy_reset_block(hw)) { + DPRINTK(DRV, ERR, "Cannot change link characteristics " + "when SoL/IDER is active.\n"); + return -EINVAL; + } + + while (test_and_set_bit(__E1000_RESETTING, &adapter->flags)) + msleep(1); + + if (ecmd->autoneg == AUTONEG_ENABLE) { + hw->autoneg = 1; + if (hw->media_type == e1000_media_type_fiber) + hw->autoneg_advertised = ADVERTISED_1000baseT_Full | + ADVERTISED_FIBRE | + ADVERTISED_Autoneg; + else + hw->autoneg_advertised = ecmd->advertising | + ADVERTISED_TP | + ADVERTISED_Autoneg; + ecmd->advertising = hw->autoneg_advertised; + } else + if (e1000_set_spd_dplx(adapter, ecmd->speed + ecmd->duplex)) { + clear_bit(__E1000_RESETTING, &adapter->flags); + return -EINVAL; + } + + /* reset the link */ + + if (netif_running(adapter->netdev)) { + e1000_down(adapter); + e1000_up(adapter); + } else + e1000_reset(adapter); + + clear_bit(__E1000_RESETTING, &adapter->flags); + return 0; +} + +static void +e1000_get_pauseparam(struct net_device *netdev, + struct ethtool_pauseparam *pause) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + struct e1000_hw *hw = &adapter->hw; + + pause->autoneg = + (adapter->fc_autoneg ? AUTONEG_ENABLE : AUTONEG_DISABLE); + + if (hw->fc == E1000_FC_RX_PAUSE) + pause->rx_pause = 1; + else if (hw->fc == E1000_FC_TX_PAUSE) + pause->tx_pause = 1; + else if (hw->fc == E1000_FC_FULL) { + pause->rx_pause = 1; + pause->tx_pause = 1; + } +} + +static int +e1000_set_pauseparam(struct net_device *netdev, + struct ethtool_pauseparam *pause) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + struct e1000_hw *hw = &adapter->hw; + int retval = 0; + + adapter->fc_autoneg = pause->autoneg; + + while (test_and_set_bit(__E1000_RESETTING, &adapter->flags)) + msleep(1); + + if (pause->rx_pause && pause->tx_pause) + hw->fc = E1000_FC_FULL; + else if (pause->rx_pause && !pause->tx_pause) + hw->fc = E1000_FC_RX_PAUSE; + else if (!pause->rx_pause && pause->tx_pause) + hw->fc = E1000_FC_TX_PAUSE; + else if (!pause->rx_pause && !pause->tx_pause) + hw->fc = E1000_FC_NONE; + + hw->original_fc = hw->fc; + + if (adapter->fc_autoneg == AUTONEG_ENABLE) { + if (netif_running(adapter->netdev)) { + e1000_down(adapter); + e1000_up(adapter); + } else + e1000_reset(adapter); + } else + retval = ((hw->media_type == e1000_media_type_fiber) ? + e1000_setup_link(hw) : e1000_force_mac_fc(hw)); + + clear_bit(__E1000_RESETTING, &adapter->flags); + return retval; +} + +static uint32_t +e1000_get_rx_csum(struct net_device *netdev) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + return adapter->rx_csum; +} + +static int +e1000_set_rx_csum(struct net_device *netdev, uint32_t data) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + adapter->rx_csum = data; + + if (netif_running(netdev)) + e1000_reinit_locked(adapter); + else + e1000_reset(adapter); + return 0; +} + +static uint32_t +e1000_get_tx_csum(struct net_device *netdev) +{ + return (netdev->features & NETIF_F_HW_CSUM) != 0; +} + +static int +e1000_set_tx_csum(struct net_device *netdev, uint32_t data) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + + if (adapter->hw.mac_type < e1000_82543) { + if (!data) + return -EINVAL; + return 0; + } + + if (data) + netdev->features |= NETIF_F_HW_CSUM; + else + netdev->features &= ~NETIF_F_HW_CSUM; + + return 0; +} + +static int +e1000_set_tso(struct net_device *netdev, uint32_t data) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + if ((adapter->hw.mac_type < e1000_82544) || + (adapter->hw.mac_type == e1000_82547)) + return data ? -EINVAL : 0; + + if (data) + netdev->features |= NETIF_F_TSO; + else + netdev->features &= ~NETIF_F_TSO; + + if (data) + netdev->features |= NETIF_F_TSO6; + else + netdev->features &= ~NETIF_F_TSO6; + + DPRINTK(PROBE, INFO, "TSO is %s\n", data ? "Enabled" : "Disabled"); + adapter->tso_force = TRUE; + return 0; +} + +static uint32_t +e1000_get_msglevel(struct net_device *netdev) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + return adapter->msg_enable; +} + +static void +e1000_set_msglevel(struct net_device *netdev, uint32_t data) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + adapter->msg_enable = data; +} + +static int +e1000_get_regs_len(struct net_device *netdev) +{ +#define E1000_REGS_LEN 32 + return E1000_REGS_LEN * sizeof(uint32_t); +} + +static void +e1000_get_regs(struct net_device *netdev, + struct ethtool_regs *regs, void *p) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + struct e1000_hw *hw = &adapter->hw; + uint32_t *regs_buff = p; + uint16_t phy_data; + + memset(p, 0, E1000_REGS_LEN * sizeof(uint32_t)); + + regs->version = (1 << 24) | (hw->revision_id << 16) | hw->device_id; + + regs_buff[0] = E1000_READ_REG(hw, CTRL); + regs_buff[1] = E1000_READ_REG(hw, STATUS); + + regs_buff[2] = E1000_READ_REG(hw, RCTL); + regs_buff[3] = E1000_READ_REG(hw, RDLEN); + regs_buff[4] = E1000_READ_REG(hw, RDH); + regs_buff[5] = E1000_READ_REG(hw, RDT); + regs_buff[6] = E1000_READ_REG(hw, RDTR); + + regs_buff[7] = E1000_READ_REG(hw, TCTL); + regs_buff[8] = E1000_READ_REG(hw, TDLEN); + regs_buff[9] = E1000_READ_REG(hw, TDH); + regs_buff[10] = E1000_READ_REG(hw, TDT); + regs_buff[11] = E1000_READ_REG(hw, TIDV); + + regs_buff[12] = adapter->hw.phy_type; /* PHY type (IGP=1, M88=0) */ + if (hw->phy_type == e1000_phy_igp) { + e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT, + IGP01E1000_PHY_AGC_A); + e1000_read_phy_reg(hw, IGP01E1000_PHY_AGC_A & + IGP01E1000_PHY_PAGE_SELECT, &phy_data); + regs_buff[13] = (uint32_t)phy_data; /* cable length */ + e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT, + IGP01E1000_PHY_AGC_B); + e1000_read_phy_reg(hw, IGP01E1000_PHY_AGC_B & + IGP01E1000_PHY_PAGE_SELECT, &phy_data); + regs_buff[14] = (uint32_t)phy_data; /* cable length */ + e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT, + IGP01E1000_PHY_AGC_C); + e1000_read_phy_reg(hw, IGP01E1000_PHY_AGC_C & + IGP01E1000_PHY_PAGE_SELECT, &phy_data); + regs_buff[15] = (uint32_t)phy_data; /* cable length */ + e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT, + IGP01E1000_PHY_AGC_D); + e1000_read_phy_reg(hw, IGP01E1000_PHY_AGC_D & + IGP01E1000_PHY_PAGE_SELECT, &phy_data); + regs_buff[16] = (uint32_t)phy_data; /* cable length */ + regs_buff[17] = 0; /* extended 10bt distance (not needed) */ + e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT, 0x0); + e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS & + IGP01E1000_PHY_PAGE_SELECT, &phy_data); + regs_buff[18] = (uint32_t)phy_data; /* cable polarity */ + e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT, + IGP01E1000_PHY_PCS_INIT_REG); + e1000_read_phy_reg(hw, IGP01E1000_PHY_PCS_INIT_REG & + IGP01E1000_PHY_PAGE_SELECT, &phy_data); + regs_buff[19] = (uint32_t)phy_data; /* cable polarity */ + regs_buff[20] = 0; /* polarity correction enabled (always) */ + regs_buff[22] = 0; /* phy receive errors (unavailable) */ + regs_buff[23] = regs_buff[18]; /* mdix mode */ + e1000_write_phy_reg(hw, IGP01E1000_PHY_PAGE_SELECT, 0x0); + } else { + e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data); + regs_buff[13] = (uint32_t)phy_data; /* cable length */ + regs_buff[14] = 0; /* Dummy (to align w/ IGP phy reg dump) */ + regs_buff[15] = 0; /* Dummy (to align w/ IGP phy reg dump) */ + regs_buff[16] = 0; /* Dummy (to align w/ IGP phy reg dump) */ + e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + regs_buff[17] = (uint32_t)phy_data; /* extended 10bt distance */ + regs_buff[18] = regs_buff[13]; /* cable polarity */ + regs_buff[19] = 0; /* Dummy (to align w/ IGP phy reg dump) */ + regs_buff[20] = regs_buff[17]; /* polarity correction */ + /* phy receive errors */ + regs_buff[22] = adapter->phy_stats.receive_errors; + regs_buff[23] = regs_buff[13]; /* mdix mode */ + } + regs_buff[21] = adapter->phy_stats.idle_errors; /* phy idle errors */ + e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data); + regs_buff[24] = (uint32_t)phy_data; /* phy local receiver status */ + regs_buff[25] = regs_buff[24]; /* phy remote receiver status */ + if (hw->mac_type >= e1000_82540 && + hw->mac_type < e1000_82571 && + hw->media_type == e1000_media_type_copper) { + regs_buff[26] = E1000_READ_REG(hw, MANC); + } +} + +static int +e1000_get_eeprom_len(struct net_device *netdev) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + return adapter->hw.eeprom.word_size * 2; +} + +static int +e1000_get_eeprom(struct net_device *netdev, + struct ethtool_eeprom *eeprom, uint8_t *bytes) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + struct e1000_hw *hw = &adapter->hw; + uint16_t *eeprom_buff; + int first_word, last_word; + int ret_val = 0; + uint16_t i; + + if (eeprom->len == 0) + return -EINVAL; + + eeprom->magic = hw->vendor_id | (hw->device_id << 16); + + first_word = eeprom->offset >> 1; + last_word = (eeprom->offset + eeprom->len - 1) >> 1; + + eeprom_buff = kmalloc(sizeof(uint16_t) * + (last_word - first_word + 1), GFP_KERNEL); + if (!eeprom_buff) + return -ENOMEM; + + if (hw->eeprom.type == e1000_eeprom_spi) + ret_val = e1000_read_eeprom(hw, first_word, + last_word - first_word + 1, + eeprom_buff); + else { + for (i = 0; i < last_word - first_word + 1; i++) + if ((ret_val = e1000_read_eeprom(hw, first_word + i, 1, + &eeprom_buff[i]))) + break; + } + + /* Device's eeprom is always little-endian, word addressable */ + for (i = 0; i < last_word - first_word + 1; i++) + le16_to_cpus(&eeprom_buff[i]); + + memcpy(bytes, (uint8_t *)eeprom_buff + (eeprom->offset & 1), + eeprom->len); + kfree(eeprom_buff); + + return ret_val; +} + +static int +e1000_set_eeprom(struct net_device *netdev, + struct ethtool_eeprom *eeprom, uint8_t *bytes) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + struct e1000_hw *hw = &adapter->hw; + uint16_t *eeprom_buff; + void *ptr; + int max_len, first_word, last_word, ret_val = 0; + uint16_t i; + + if (eeprom->len == 0) + return -EOPNOTSUPP; + + if (eeprom->magic != (hw->vendor_id | (hw->device_id << 16))) + return -EFAULT; + + max_len = hw->eeprom.word_size * 2; + + first_word = eeprom->offset >> 1; + last_word = (eeprom->offset + eeprom->len - 1) >> 1; + eeprom_buff = kmalloc(max_len, GFP_KERNEL); + if (!eeprom_buff) + return -ENOMEM; + + ptr = (void *)eeprom_buff; + + if (eeprom->offset & 1) { + /* need read/modify/write of first changed EEPROM word */ + /* only the second byte of the word is being modified */ + ret_val = e1000_read_eeprom(hw, first_word, 1, + &eeprom_buff[0]); + ptr++; + } + if (((eeprom->offset + eeprom->len) & 1) && (ret_val == 0)) { + /* need read/modify/write of last changed EEPROM word */ + /* only the first byte of the word is being modified */ + ret_val = e1000_read_eeprom(hw, last_word, 1, + &eeprom_buff[last_word - first_word]); + } + + /* Device's eeprom is always little-endian, word addressable */ + for (i = 0; i < last_word - first_word + 1; i++) + le16_to_cpus(&eeprom_buff[i]); + + memcpy(ptr, bytes, eeprom->len); + + for (i = 0; i < last_word - first_word + 1; i++) + eeprom_buff[i] = cpu_to_le16(eeprom_buff[i]); + + ret_val = e1000_write_eeprom(hw, first_word, + last_word - first_word + 1, eeprom_buff); + + /* Update the checksum over the first part of the EEPROM if needed + * and flush shadow RAM for 82573 conrollers */ + if ((ret_val == 0) && ((first_word <= EEPROM_CHECKSUM_REG) || + (hw->mac_type == e1000_82573))) + e1000_update_eeprom_checksum(hw); + + kfree(eeprom_buff); + return ret_val; +} + +static void +e1000_get_drvinfo(struct net_device *netdev, + struct ethtool_drvinfo *drvinfo) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + char firmware_version[32]; + uint16_t eeprom_data; + + strncpy(drvinfo->driver, e1000_driver_name, 32); + strncpy(drvinfo->version, e1000_driver_version, 32); + + /* EEPROM image version # is reported as firmware version # for + * 8257{1|2|3} controllers */ + e1000_read_eeprom(&adapter->hw, 5, 1, &eeprom_data); + switch (adapter->hw.mac_type) { + case e1000_82571: + case e1000_82572: + case e1000_82573: + case e1000_80003es2lan: + case e1000_ich8lan: + sprintf(firmware_version, "%d.%d-%d", + (eeprom_data & 0xF000) >> 12, + (eeprom_data & 0x0FF0) >> 4, + eeprom_data & 0x000F); + break; + default: + sprintf(firmware_version, "N/A"); + } + + strncpy(drvinfo->fw_version, firmware_version, 32); + strncpy(drvinfo->bus_info, pci_name(adapter->pdev), 32); + drvinfo->regdump_len = e1000_get_regs_len(netdev); + drvinfo->eedump_len = e1000_get_eeprom_len(netdev); +} + +static void +e1000_get_ringparam(struct net_device *netdev, + struct ethtool_ringparam *ring) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + e1000_mac_type mac_type = adapter->hw.mac_type; + struct e1000_tx_ring *txdr = adapter->tx_ring; + struct e1000_rx_ring *rxdr = adapter->rx_ring; + + ring->rx_max_pending = (mac_type < e1000_82544) ? E1000_MAX_RXD : + E1000_MAX_82544_RXD; + ring->tx_max_pending = (mac_type < e1000_82544) ? E1000_MAX_TXD : + E1000_MAX_82544_TXD; + ring->rx_mini_max_pending = 0; + ring->rx_jumbo_max_pending = 0; + ring->rx_pending = rxdr->count; + ring->tx_pending = txdr->count; + ring->rx_mini_pending = 0; + ring->rx_jumbo_pending = 0; +} + +static int +e1000_set_ringparam(struct net_device *netdev, + struct ethtool_ringparam *ring) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + e1000_mac_type mac_type = adapter->hw.mac_type; + struct e1000_tx_ring *txdr, *tx_old; + struct e1000_rx_ring *rxdr, *rx_old; + int i, err; + + if ((ring->rx_mini_pending) || (ring->rx_jumbo_pending)) + return -EINVAL; + + while (test_and_set_bit(__E1000_RESETTING, &adapter->flags)) + msleep(1); + + if (netif_running(adapter->netdev)) + e1000_down(adapter); + + tx_old = adapter->tx_ring; + rx_old = adapter->rx_ring; + + err = -ENOMEM; + txdr = kcalloc(adapter->num_tx_queues, sizeof(struct e1000_tx_ring), GFP_KERNEL); + if (!txdr) + goto err_alloc_tx; + + rxdr = kcalloc(adapter->num_rx_queues, sizeof(struct e1000_rx_ring), GFP_KERNEL); + if (!rxdr) + goto err_alloc_rx; + + adapter->tx_ring = txdr; + adapter->rx_ring = rxdr; + + rxdr->count = max(ring->rx_pending,(uint32_t)E1000_MIN_RXD); + rxdr->count = min(rxdr->count,(uint32_t)(mac_type < e1000_82544 ? + E1000_MAX_RXD : E1000_MAX_82544_RXD)); + rxdr->count = ALIGN(rxdr->count, REQ_RX_DESCRIPTOR_MULTIPLE); + + txdr->count = max(ring->tx_pending,(uint32_t)E1000_MIN_TXD); + txdr->count = min(txdr->count,(uint32_t)(mac_type < e1000_82544 ? + E1000_MAX_TXD : E1000_MAX_82544_TXD)); + txdr->count = ALIGN(txdr->count, REQ_TX_DESCRIPTOR_MULTIPLE); + + for (i = 0; i < adapter->num_tx_queues; i++) + txdr[i].count = txdr->count; + for (i = 0; i < adapter->num_rx_queues; i++) + rxdr[i].count = rxdr->count; + + if (netif_running(adapter->netdev)) { + /* Try to get new resources before deleting old */ + if ((err = e1000_setup_all_rx_resources(adapter))) + goto err_setup_rx; + if ((err = e1000_setup_all_tx_resources(adapter))) + goto err_setup_tx; + + /* save the new, restore the old in order to free it, + * then restore the new back again */ + + adapter->rx_ring = rx_old; + adapter->tx_ring = tx_old; + e1000_free_all_rx_resources(adapter); + e1000_free_all_tx_resources(adapter); + kfree(tx_old); + kfree(rx_old); + adapter->rx_ring = rxdr; + adapter->tx_ring = txdr; + if ((err = e1000_up(adapter))) + goto err_setup; + } + + clear_bit(__E1000_RESETTING, &adapter->flags); + return 0; +err_setup_tx: + e1000_free_all_rx_resources(adapter); +err_setup_rx: + adapter->rx_ring = rx_old; + adapter->tx_ring = tx_old; + kfree(rxdr); +err_alloc_rx: + kfree(txdr); +err_alloc_tx: + e1000_up(adapter); +err_setup: + clear_bit(__E1000_RESETTING, &adapter->flags); + return err; +} + +#define REG_PATTERN_TEST(R, M, W) \ +{ \ + uint32_t pat, val; \ + const uint32_t test[] = \ + {0x5A5A5A5A, 0xA5A5A5A5, 0x00000000, 0xFFFFFFFF}; \ + for (pat = 0; pat < ARRAY_SIZE(test); pat++) { \ + E1000_WRITE_REG(&adapter->hw, R, (test[pat] & W)); \ + val = E1000_READ_REG(&adapter->hw, R); \ + if (val != (test[pat] & W & M)) { \ + DPRINTK(DRV, ERR, "pattern test reg %04X failed: got " \ + "0x%08X expected 0x%08X\n", \ + E1000_##R, val, (test[pat] & W & M)); \ + *data = (adapter->hw.mac_type < e1000_82543) ? \ + E1000_82542_##R : E1000_##R; \ + return 1; \ + } \ + } \ +} + +#define REG_SET_AND_CHECK(R, M, W) \ +{ \ + uint32_t val; \ + E1000_WRITE_REG(&adapter->hw, R, W & M); \ + val = E1000_READ_REG(&adapter->hw, R); \ + if ((W & M) != (val & M)) { \ + DPRINTK(DRV, ERR, "set/check reg %04X test failed: got 0x%08X "\ + "expected 0x%08X\n", E1000_##R, (val & M), (W & M)); \ + *data = (adapter->hw.mac_type < e1000_82543) ? \ + E1000_82542_##R : E1000_##R; \ + return 1; \ + } \ +} + +static int +e1000_reg_test(struct e1000_adapter *adapter, uint64_t *data) +{ + uint32_t value, before, after; + uint32_t i, toggle; + + /* The status register is Read Only, so a write should fail. + * Some bits that get toggled are ignored. + */ + switch (adapter->hw.mac_type) { + /* there are several bits on newer hardware that are r/w */ + case e1000_82571: + case e1000_82572: + case e1000_80003es2lan: + toggle = 0x7FFFF3FF; + break; + case e1000_82573: + case e1000_ich8lan: + toggle = 0x7FFFF033; + break; + default: + toggle = 0xFFFFF833; + break; + } + + before = E1000_READ_REG(&adapter->hw, STATUS); + value = (E1000_READ_REG(&adapter->hw, STATUS) & toggle); + E1000_WRITE_REG(&adapter->hw, STATUS, toggle); + after = E1000_READ_REG(&adapter->hw, STATUS) & toggle; + if (value != after) { + DPRINTK(DRV, ERR, "failed STATUS register test got: " + "0x%08X expected: 0x%08X\n", after, value); + *data = 1; + return 1; + } + /* restore previous status */ + E1000_WRITE_REG(&adapter->hw, STATUS, before); + + if (adapter->hw.mac_type != e1000_ich8lan) { + REG_PATTERN_TEST(FCAL, 0xFFFFFFFF, 0xFFFFFFFF); + REG_PATTERN_TEST(FCAH, 0x0000FFFF, 0xFFFFFFFF); + REG_PATTERN_TEST(FCT, 0x0000FFFF, 0xFFFFFFFF); + REG_PATTERN_TEST(VET, 0x0000FFFF, 0xFFFFFFFF); + } + + REG_PATTERN_TEST(RDTR, 0x0000FFFF, 0xFFFFFFFF); + REG_PATTERN_TEST(RDBAH, 0xFFFFFFFF, 0xFFFFFFFF); + REG_PATTERN_TEST(RDLEN, 0x000FFF80, 0x000FFFFF); + REG_PATTERN_TEST(RDH, 0x0000FFFF, 0x0000FFFF); + REG_PATTERN_TEST(RDT, 0x0000FFFF, 0x0000FFFF); + REG_PATTERN_TEST(FCRTH, 0x0000FFF8, 0x0000FFF8); + REG_PATTERN_TEST(FCTTV, 0x0000FFFF, 0x0000FFFF); + REG_PATTERN_TEST(TIPG, 0x3FFFFFFF, 0x3FFFFFFF); + REG_PATTERN_TEST(TDBAH, 0xFFFFFFFF, 0xFFFFFFFF); + REG_PATTERN_TEST(TDLEN, 0x000FFF80, 0x000FFFFF); + + REG_SET_AND_CHECK(RCTL, 0xFFFFFFFF, 0x00000000); + + before = (adapter->hw.mac_type == e1000_ich8lan ? + 0x06C3B33E : 0x06DFB3FE); + REG_SET_AND_CHECK(RCTL, before, 0x003FFFFB); + REG_SET_AND_CHECK(TCTL, 0xFFFFFFFF, 0x00000000); + + if (adapter->hw.mac_type >= e1000_82543) { + + REG_SET_AND_CHECK(RCTL, before, 0xFFFFFFFF); + REG_PATTERN_TEST(RDBAL, 0xFFFFFFF0, 0xFFFFFFFF); + if (adapter->hw.mac_type != e1000_ich8lan) + REG_PATTERN_TEST(TXCW, 0xC000FFFF, 0x0000FFFF); + REG_PATTERN_TEST(TDBAL, 0xFFFFFFF0, 0xFFFFFFFF); + REG_PATTERN_TEST(TIDV, 0x0000FFFF, 0x0000FFFF); + value = (adapter->hw.mac_type == e1000_ich8lan ? + E1000_RAR_ENTRIES_ICH8LAN : E1000_RAR_ENTRIES); + for (i = 0; i < value; i++) { + REG_PATTERN_TEST(RA + (((i << 1) + 1) << 2), 0x8003FFFF, + 0xFFFFFFFF); + } + + } else { + + REG_SET_AND_CHECK(RCTL, 0xFFFFFFFF, 0x01FFFFFF); + REG_PATTERN_TEST(RDBAL, 0xFFFFF000, 0xFFFFFFFF); + REG_PATTERN_TEST(TXCW, 0x0000FFFF, 0x0000FFFF); + REG_PATTERN_TEST(TDBAL, 0xFFFFF000, 0xFFFFFFFF); + + } + + value = (adapter->hw.mac_type == e1000_ich8lan ? + E1000_MC_TBL_SIZE_ICH8LAN : E1000_MC_TBL_SIZE); + for (i = 0; i < value; i++) + REG_PATTERN_TEST(MTA + (i << 2), 0xFFFFFFFF, 0xFFFFFFFF); + + *data = 0; + return 0; +} + +static int +e1000_eeprom_test(struct e1000_adapter *adapter, uint64_t *data) +{ + uint16_t temp; + uint16_t checksum = 0; + uint16_t i; + + *data = 0; + /* Read and add up the contents of the EEPROM */ + for (i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) { + if ((e1000_read_eeprom(&adapter->hw, i, 1, &temp)) < 0) { + *data = 1; + break; + } + checksum += temp; + } + + /* If Checksum is not Correct return error else test passed */ + if ((checksum != (uint16_t) EEPROM_SUM) && !(*data)) + *data = 2; + + return *data; +} + +static irqreturn_t +e1000_test_intr(int irq, void *data) +{ + struct net_device *netdev = (struct net_device *) data; + struct e1000_adapter *adapter = netdev_priv(netdev); + + adapter->test_icr |= E1000_READ_REG(&adapter->hw, ICR); + + return IRQ_HANDLED; +} + +static int +e1000_intr_test(struct e1000_adapter *adapter, uint64_t *data) +{ + struct net_device *netdev = adapter->netdev; + uint32_t mask, i=0, shared_int = TRUE; + uint32_t irq = adapter->pdev->irq; + + *data = 0; + + /* NOTE: we don't test MSI interrupts here, yet */ + /* Hook up test interrupt handler just for this test */ + if (!request_irq(irq, &e1000_test_intr, IRQF_PROBE_SHARED, netdev->name, + netdev)) + shared_int = FALSE; + else if (request_irq(irq, &e1000_test_intr, IRQF_SHARED, + netdev->name, netdev)) { + *data = 1; + return -1; + } + DPRINTK(HW, INFO, "testing %s interrupt\n", + (shared_int ? "shared" : "unshared")); + + /* Disable all the interrupts */ + E1000_WRITE_REG(&adapter->hw, IMC, 0xFFFFFFFF); + msleep(10); + + /* Test each interrupt */ + for (; i < 10; i++) { + + if (adapter->hw.mac_type == e1000_ich8lan && i == 8) + continue; + + /* Interrupt to test */ + mask = 1 << i; + + if (!shared_int) { + /* Disable the interrupt to be reported in + * the cause register and then force the same + * interrupt and see if one gets posted. If + * an interrupt was posted to the bus, the + * test failed. + */ + adapter->test_icr = 0; + E1000_WRITE_REG(&adapter->hw, IMC, mask); + E1000_WRITE_REG(&adapter->hw, ICS, mask); + msleep(10); + + if (adapter->test_icr & mask) { + *data = 3; + break; + } + } + + /* Enable the interrupt to be reported in + * the cause register and then force the same + * interrupt and see if one gets posted. If + * an interrupt was not posted to the bus, the + * test failed. + */ + adapter->test_icr = 0; + E1000_WRITE_REG(&adapter->hw, IMS, mask); + E1000_WRITE_REG(&adapter->hw, ICS, mask); + msleep(10); + + if (!(adapter->test_icr & mask)) { + *data = 4; + break; + } + + if (!shared_int) { + /* Disable the other interrupts to be reported in + * the cause register and then force the other + * interrupts and see if any get posted. If + * an interrupt was posted to the bus, the + * test failed. + */ + adapter->test_icr = 0; + E1000_WRITE_REG(&adapter->hw, IMC, ~mask & 0x00007FFF); + E1000_WRITE_REG(&adapter->hw, ICS, ~mask & 0x00007FFF); + msleep(10); + + if (adapter->test_icr) { + *data = 5; + break; + } + } + } + + /* Disable all the interrupts */ + E1000_WRITE_REG(&adapter->hw, IMC, 0xFFFFFFFF); + msleep(10); + + /* Unhook test interrupt handler */ + free_irq(irq, netdev); + + return *data; +} + +static void +e1000_free_desc_rings(struct e1000_adapter *adapter) +{ + struct e1000_tx_ring *txdr = &adapter->test_tx_ring; + struct e1000_rx_ring *rxdr = &adapter->test_rx_ring; + struct pci_dev *pdev = adapter->pdev; + int i; + + if (txdr->desc && txdr->buffer_info) { + for (i = 0; i < txdr->count; i++) { + if (txdr->buffer_info[i].dma) + pci_unmap_single(pdev, txdr->buffer_info[i].dma, + txdr->buffer_info[i].length, + PCI_DMA_TODEVICE); + if (txdr->buffer_info[i].skb) + dev_kfree_skb(txdr->buffer_info[i].skb); + } + } + + if (rxdr->desc && rxdr->buffer_info) { + for (i = 0; i < rxdr->count; i++) { + if (rxdr->buffer_info[i].dma) + pci_unmap_single(pdev, rxdr->buffer_info[i].dma, + rxdr->buffer_info[i].length, + PCI_DMA_FROMDEVICE); + if (rxdr->buffer_info[i].skb) + dev_kfree_skb(rxdr->buffer_info[i].skb); + } + } + + if (txdr->desc) { + pci_free_consistent(pdev, txdr->size, txdr->desc, txdr->dma); + txdr->desc = NULL; + } + if (rxdr->desc) { + pci_free_consistent(pdev, rxdr->size, rxdr->desc, rxdr->dma); + rxdr->desc = NULL; + } + + kfree(txdr->buffer_info); + txdr->buffer_info = NULL; + kfree(rxdr->buffer_info); + rxdr->buffer_info = NULL; + + return; +} + +static int +e1000_setup_desc_rings(struct e1000_adapter *adapter) +{ + struct e1000_tx_ring *txdr = &adapter->test_tx_ring; + struct e1000_rx_ring *rxdr = &adapter->test_rx_ring; + struct pci_dev *pdev = adapter->pdev; + uint32_t rctl; + int i, ret_val; + + /* Setup Tx descriptor ring and Tx buffers */ + + if (!txdr->count) + txdr->count = E1000_DEFAULT_TXD; + + if (!(txdr->buffer_info = kcalloc(txdr->count, + sizeof(struct e1000_buffer), + GFP_KERNEL))) { + ret_val = 1; + goto err_nomem; + } + + txdr->size = txdr->count * sizeof(struct e1000_tx_desc); + txdr->size = ALIGN(txdr->size, 4096); + if (!(txdr->desc = pci_alloc_consistent(pdev, txdr->size, + &txdr->dma))) { + ret_val = 2; + goto err_nomem; + } + memset(txdr->desc, 0, txdr->size); + txdr->next_to_use = txdr->next_to_clean = 0; + + E1000_WRITE_REG(&adapter->hw, TDBAL, + ((uint64_t) txdr->dma & 0x00000000FFFFFFFF)); + E1000_WRITE_REG(&adapter->hw, TDBAH, ((uint64_t) txdr->dma >> 32)); + E1000_WRITE_REG(&adapter->hw, TDLEN, + txdr->count * sizeof(struct e1000_tx_desc)); + E1000_WRITE_REG(&adapter->hw, TDH, 0); + E1000_WRITE_REG(&adapter->hw, TDT, 0); + E1000_WRITE_REG(&adapter->hw, TCTL, + E1000_TCTL_PSP | E1000_TCTL_EN | + E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT | + E1000_FDX_COLLISION_DISTANCE << E1000_COLD_SHIFT); + + for (i = 0; i < txdr->count; i++) { + struct e1000_tx_desc *tx_desc = E1000_TX_DESC(*txdr, i); + struct sk_buff *skb; + unsigned int size = 1024; + + if (!(skb = alloc_skb(size, GFP_KERNEL))) { + ret_val = 3; + goto err_nomem; + } + skb_put(skb, size); + txdr->buffer_info[i].skb = skb; + txdr->buffer_info[i].length = skb->len; + txdr->buffer_info[i].dma = + pci_map_single(pdev, skb->data, skb->len, + PCI_DMA_TODEVICE); + tx_desc->buffer_addr = cpu_to_le64(txdr->buffer_info[i].dma); + tx_desc->lower.data = cpu_to_le32(skb->len); + tx_desc->lower.data |= cpu_to_le32(E1000_TXD_CMD_EOP | + E1000_TXD_CMD_IFCS | + E1000_TXD_CMD_RPS); + tx_desc->upper.data = 0; + } + + /* Setup Rx descriptor ring and Rx buffers */ + + if (!rxdr->count) + rxdr->count = E1000_DEFAULT_RXD; + + if (!(rxdr->buffer_info = kcalloc(rxdr->count, + sizeof(struct e1000_buffer), + GFP_KERNEL))) { + ret_val = 4; + goto err_nomem; + } + + rxdr->size = rxdr->count * sizeof(struct e1000_rx_desc); + if (!(rxdr->desc = pci_alloc_consistent(pdev, rxdr->size, &rxdr->dma))) { + ret_val = 5; + goto err_nomem; + } + memset(rxdr->desc, 0, rxdr->size); + rxdr->next_to_use = rxdr->next_to_clean = 0; + + rctl = E1000_READ_REG(&adapter->hw, RCTL); + E1000_WRITE_REG(&adapter->hw, RCTL, rctl & ~E1000_RCTL_EN); + E1000_WRITE_REG(&adapter->hw, RDBAL, + ((uint64_t) rxdr->dma & 0xFFFFFFFF)); + E1000_WRITE_REG(&adapter->hw, RDBAH, ((uint64_t) rxdr->dma >> 32)); + E1000_WRITE_REG(&adapter->hw, RDLEN, rxdr->size); + E1000_WRITE_REG(&adapter->hw, RDH, 0); + E1000_WRITE_REG(&adapter->hw, RDT, 0); + rctl = E1000_RCTL_EN | E1000_RCTL_BAM | E1000_RCTL_SZ_2048 | + E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF | + (adapter->hw.mc_filter_type << E1000_RCTL_MO_SHIFT); + E1000_WRITE_REG(&adapter->hw, RCTL, rctl); + + for (i = 0; i < rxdr->count; i++) { + struct e1000_rx_desc *rx_desc = E1000_RX_DESC(*rxdr, i); + struct sk_buff *skb; + + if (!(skb = alloc_skb(E1000_RXBUFFER_2048 + NET_IP_ALIGN, + GFP_KERNEL))) { + ret_val = 6; + goto err_nomem; + } + skb_reserve(skb, NET_IP_ALIGN); + rxdr->buffer_info[i].skb = skb; + rxdr->buffer_info[i].length = E1000_RXBUFFER_2048; + rxdr->buffer_info[i].dma = + pci_map_single(pdev, skb->data, E1000_RXBUFFER_2048, + PCI_DMA_FROMDEVICE); + rx_desc->buffer_addr = cpu_to_le64(rxdr->buffer_info[i].dma); + memset(skb->data, 0x00, skb->len); + } + + return 0; + +err_nomem: + e1000_free_desc_rings(adapter); + return ret_val; +} + +static void +e1000_phy_disable_receiver(struct e1000_adapter *adapter) +{ + /* Write out to PHY registers 29 and 30 to disable the Receiver. */ + e1000_write_phy_reg(&adapter->hw, 29, 0x001F); + e1000_write_phy_reg(&adapter->hw, 30, 0x8FFC); + e1000_write_phy_reg(&adapter->hw, 29, 0x001A); + e1000_write_phy_reg(&adapter->hw, 30, 0x8FF0); +} + +static void +e1000_phy_reset_clk_and_crs(struct e1000_adapter *adapter) +{ + uint16_t phy_reg; + + /* Because we reset the PHY above, we need to re-force TX_CLK in the + * Extended PHY Specific Control Register to 25MHz clock. This + * value defaults back to a 2.5MHz clock when the PHY is reset. + */ + e1000_read_phy_reg(&adapter->hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_reg); + phy_reg |= M88E1000_EPSCR_TX_CLK_25; + e1000_write_phy_reg(&adapter->hw, + M88E1000_EXT_PHY_SPEC_CTRL, phy_reg); + + /* In addition, because of the s/w reset above, we need to enable + * CRS on TX. This must be set for both full and half duplex + * operation. + */ + e1000_read_phy_reg(&adapter->hw, M88E1000_PHY_SPEC_CTRL, &phy_reg); + phy_reg |= M88E1000_PSCR_ASSERT_CRS_ON_TX; + e1000_write_phy_reg(&adapter->hw, + M88E1000_PHY_SPEC_CTRL, phy_reg); +} + +static int +e1000_nonintegrated_phy_loopback(struct e1000_adapter *adapter) +{ + uint32_t ctrl_reg; + uint16_t phy_reg; + + /* Setup the Device Control Register for PHY loopback test. */ + + ctrl_reg = E1000_READ_REG(&adapter->hw, CTRL); + ctrl_reg |= (E1000_CTRL_ILOS | /* Invert Loss-Of-Signal */ + E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */ + E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */ + E1000_CTRL_SPD_1000 | /* Force Speed to 1000 */ + E1000_CTRL_FD); /* Force Duplex to FULL */ + + E1000_WRITE_REG(&adapter->hw, CTRL, ctrl_reg); + + /* Read the PHY Specific Control Register (0x10) */ + e1000_read_phy_reg(&adapter->hw, M88E1000_PHY_SPEC_CTRL, &phy_reg); + + /* Clear Auto-Crossover bits in PHY Specific Control Register + * (bits 6:5). + */ + phy_reg &= ~M88E1000_PSCR_AUTO_X_MODE; + e1000_write_phy_reg(&adapter->hw, M88E1000_PHY_SPEC_CTRL, phy_reg); + + /* Perform software reset on the PHY */ + e1000_phy_reset(&adapter->hw); + + /* Have to setup TX_CLK and TX_CRS after software reset */ + e1000_phy_reset_clk_and_crs(adapter); + + e1000_write_phy_reg(&adapter->hw, PHY_CTRL, 0x8100); + + /* Wait for reset to complete. */ + udelay(500); + + /* Have to setup TX_CLK and TX_CRS after software reset */ + e1000_phy_reset_clk_and_crs(adapter); + + /* Write out to PHY registers 29 and 30 to disable the Receiver. */ + e1000_phy_disable_receiver(adapter); + + /* Set the loopback bit in the PHY control register. */ + e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &phy_reg); + phy_reg |= MII_CR_LOOPBACK; + e1000_write_phy_reg(&adapter->hw, PHY_CTRL, phy_reg); + + /* Setup TX_CLK and TX_CRS one more time. */ + e1000_phy_reset_clk_and_crs(adapter); + + /* Check Phy Configuration */ + e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &phy_reg); + if (phy_reg != 0x4100) + return 9; + + e1000_read_phy_reg(&adapter->hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_reg); + if (phy_reg != 0x0070) + return 10; + + e1000_read_phy_reg(&adapter->hw, 29, &phy_reg); + if (phy_reg != 0x001A) + return 11; + + return 0; +} + +static int +e1000_integrated_phy_loopback(struct e1000_adapter *adapter) +{ + uint32_t ctrl_reg = 0; + uint32_t stat_reg = 0; + + adapter->hw.autoneg = FALSE; + + if (adapter->hw.phy_type == e1000_phy_m88) { + /* Auto-MDI/MDIX Off */ + e1000_write_phy_reg(&adapter->hw, + M88E1000_PHY_SPEC_CTRL, 0x0808); + /* reset to update Auto-MDI/MDIX */ + e1000_write_phy_reg(&adapter->hw, PHY_CTRL, 0x9140); + /* autoneg off */ + e1000_write_phy_reg(&adapter->hw, PHY_CTRL, 0x8140); + } else if (adapter->hw.phy_type == e1000_phy_gg82563) + e1000_write_phy_reg(&adapter->hw, + GG82563_PHY_KMRN_MODE_CTRL, + 0x1CC); + + ctrl_reg = E1000_READ_REG(&adapter->hw, CTRL); + + if (adapter->hw.phy_type == e1000_phy_ife) { + /* force 100, set loopback */ + e1000_write_phy_reg(&adapter->hw, PHY_CTRL, 0x6100); + + /* Now set up the MAC to the same speed/duplex as the PHY. */ + ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */ + ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */ + E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */ + E1000_CTRL_SPD_100 |/* Force Speed to 100 */ + E1000_CTRL_FD); /* Force Duplex to FULL */ + } else { + /* force 1000, set loopback */ + e1000_write_phy_reg(&adapter->hw, PHY_CTRL, 0x4140); + + /* Now set up the MAC to the same speed/duplex as the PHY. */ + ctrl_reg = E1000_READ_REG(&adapter->hw, CTRL); + ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */ + ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */ + E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */ + E1000_CTRL_SPD_1000 |/* Force Speed to 1000 */ + E1000_CTRL_FD); /* Force Duplex to FULL */ + } + + if (adapter->hw.media_type == e1000_media_type_copper && + adapter->hw.phy_type == e1000_phy_m88) + ctrl_reg |= E1000_CTRL_ILOS; /* Invert Loss of Signal */ + else { + /* Set the ILOS bit on the fiber Nic is half + * duplex link is detected. */ + stat_reg = E1000_READ_REG(&adapter->hw, STATUS); + if ((stat_reg & E1000_STATUS_FD) == 0) + ctrl_reg |= (E1000_CTRL_ILOS | E1000_CTRL_SLU); + } + + E1000_WRITE_REG(&adapter->hw, CTRL, ctrl_reg); + + /* Disable the receiver on the PHY so when a cable is plugged in, the + * PHY does not begin to autoneg when a cable is reconnected to the NIC. + */ + if (adapter->hw.phy_type == e1000_phy_m88) + e1000_phy_disable_receiver(adapter); + + udelay(500); + + return 0; +} + +static int +e1000_set_phy_loopback(struct e1000_adapter *adapter) +{ + uint16_t phy_reg = 0; + uint16_t count = 0; + + switch (adapter->hw.mac_type) { + case e1000_82543: + if (adapter->hw.media_type == e1000_media_type_copper) { + /* Attempt to setup Loopback mode on Non-integrated PHY. + * Some PHY registers get corrupted at random, so + * attempt this 10 times. + */ + while (e1000_nonintegrated_phy_loopback(adapter) && + count++ < 10); + if (count < 11) + return 0; + } + break; + + case e1000_82544: + case e1000_82540: + case e1000_82545: + case e1000_82545_rev_3: + case e1000_82546: + case e1000_82546_rev_3: + case e1000_82541: + case e1000_82541_rev_2: + case e1000_82547: + case e1000_82547_rev_2: + case e1000_82571: + case e1000_82572: + case e1000_82573: + case e1000_80003es2lan: + case e1000_ich8lan: + return e1000_integrated_phy_loopback(adapter); + break; + + default: + /* Default PHY loopback work is to read the MII + * control register and assert bit 14 (loopback mode). + */ + e1000_read_phy_reg(&adapter->hw, PHY_CTRL, &phy_reg); + phy_reg |= MII_CR_LOOPBACK; + e1000_write_phy_reg(&adapter->hw, PHY_CTRL, phy_reg); + return 0; + break; + } + + return 8; +} + +static int +e1000_setup_loopback_test(struct e1000_adapter *adapter) +{ + struct e1000_hw *hw = &adapter->hw; + uint32_t rctl; + + if (hw->media_type == e1000_media_type_fiber || + hw->media_type == e1000_media_type_internal_serdes) { + switch (hw->mac_type) { + case e1000_82545: + case e1000_82546: + case e1000_82545_rev_3: + case e1000_82546_rev_3: + return e1000_set_phy_loopback(adapter); + break; + case e1000_82571: + case e1000_82572: +#define E1000_SERDES_LB_ON 0x410 + e1000_set_phy_loopback(adapter); + E1000_WRITE_REG(hw, SCTL, E1000_SERDES_LB_ON); + msleep(10); + return 0; + break; + default: + rctl = E1000_READ_REG(hw, RCTL); + rctl |= E1000_RCTL_LBM_TCVR; + E1000_WRITE_REG(hw, RCTL, rctl); + return 0; + } + } else if (hw->media_type == e1000_media_type_copper) + return e1000_set_phy_loopback(adapter); + + return 7; +} + +static void +e1000_loopback_cleanup(struct e1000_adapter *adapter) +{ + struct e1000_hw *hw = &adapter->hw; + uint32_t rctl; + uint16_t phy_reg; + + rctl = E1000_READ_REG(hw, RCTL); + rctl &= ~(E1000_RCTL_LBM_TCVR | E1000_RCTL_LBM_MAC); + E1000_WRITE_REG(hw, RCTL, rctl); + + switch (hw->mac_type) { + case e1000_82571: + case e1000_82572: + if (hw->media_type == e1000_media_type_fiber || + hw->media_type == e1000_media_type_internal_serdes) { +#define E1000_SERDES_LB_OFF 0x400 + E1000_WRITE_REG(hw, SCTL, E1000_SERDES_LB_OFF); + msleep(10); + break; + } + /* Fall Through */ + case e1000_82545: + case e1000_82546: + case e1000_82545_rev_3: + case e1000_82546_rev_3: + default: + hw->autoneg = TRUE; + if (hw->phy_type == e1000_phy_gg82563) + e1000_write_phy_reg(hw, + GG82563_PHY_KMRN_MODE_CTRL, + 0x180); + e1000_read_phy_reg(hw, PHY_CTRL, &phy_reg); + if (phy_reg & MII_CR_LOOPBACK) { + phy_reg &= ~MII_CR_LOOPBACK; + e1000_write_phy_reg(hw, PHY_CTRL, phy_reg); + e1000_phy_reset(hw); + } + break; + } +} + +static void +e1000_create_lbtest_frame(struct sk_buff *skb, unsigned int frame_size) +{ + memset(skb->data, 0xFF, frame_size); + frame_size &= ~1; + memset(&skb->data[frame_size / 2], 0xAA, frame_size / 2 - 1); + memset(&skb->data[frame_size / 2 + 10], 0xBE, 1); + memset(&skb->data[frame_size / 2 + 12], 0xAF, 1); +} + +static int +e1000_check_lbtest_frame(struct sk_buff *skb, unsigned int frame_size) +{ + frame_size &= ~1; + if (*(skb->data + 3) == 0xFF) { + if ((*(skb->data + frame_size / 2 + 10) == 0xBE) && + (*(skb->data + frame_size / 2 + 12) == 0xAF)) { + return 0; + } + } + return 13; +} + +static int +e1000_run_loopback_test(struct e1000_adapter *adapter) +{ + struct e1000_tx_ring *txdr = &adapter->test_tx_ring; + struct e1000_rx_ring *rxdr = &adapter->test_rx_ring; + struct pci_dev *pdev = adapter->pdev; + int i, j, k, l, lc, good_cnt, ret_val=0; + unsigned long time; + + E1000_WRITE_REG(&adapter->hw, RDT, rxdr->count - 1); + + /* Calculate the loop count based on the largest descriptor ring + * The idea is to wrap the largest ring a number of times using 64 + * send/receive pairs during each loop + */ + + if (rxdr->count <= txdr->count) + lc = ((txdr->count / 64) * 2) + 1; + else + lc = ((rxdr->count / 64) * 2) + 1; + + k = l = 0; + for (j = 0; j <= lc; j++) { /* loop count loop */ + for (i = 0; i < 64; i++) { /* send the packets */ + e1000_create_lbtest_frame(txdr->buffer_info[i].skb, + 1024); + pci_dma_sync_single_for_device(pdev, + txdr->buffer_info[k].dma, + txdr->buffer_info[k].length, + PCI_DMA_TODEVICE); + if (unlikely(++k == txdr->count)) k = 0; + } + E1000_WRITE_REG(&adapter->hw, TDT, k); + msleep(200); + time = jiffies; /* set the start time for the receive */ + good_cnt = 0; + do { /* receive the sent packets */ + pci_dma_sync_single_for_cpu(pdev, + rxdr->buffer_info[l].dma, + rxdr->buffer_info[l].length, + PCI_DMA_FROMDEVICE); + + ret_val = e1000_check_lbtest_frame( + rxdr->buffer_info[l].skb, + 1024); + if (!ret_val) + good_cnt++; + if (unlikely(++l == rxdr->count)) l = 0; + /* time + 20 msecs (200 msecs on 2.4) is more than + * enough time to complete the receives, if it's + * exceeded, break and error off + */ + } while (good_cnt < 64 && jiffies < (time + 20)); + if (good_cnt != 64) { + ret_val = 13; /* ret_val is the same as mis-compare */ + break; + } + if (jiffies >= (time + 2)) { + ret_val = 14; /* error code for time out error */ + break; + } + } /* end loop count loop */ + return ret_val; +} + +static int +e1000_loopback_test(struct e1000_adapter *adapter, uint64_t *data) +{ + /* PHY loopback cannot be performed if SoL/IDER + * sessions are active */ + if (e1000_check_phy_reset_block(&adapter->hw)) { + DPRINTK(DRV, ERR, "Cannot do PHY loopback test " + "when SoL/IDER is active.\n"); + *data = 0; + goto out; + } + + if ((*data = e1000_setup_desc_rings(adapter))) + goto out; + if ((*data = e1000_setup_loopback_test(adapter))) + goto err_loopback; + *data = e1000_run_loopback_test(adapter); + e1000_loopback_cleanup(adapter); + +err_loopback: + e1000_free_desc_rings(adapter); +out: + return *data; +} + +static int +e1000_link_test(struct e1000_adapter *adapter, uint64_t *data) +{ + *data = 0; + if (adapter->hw.media_type == e1000_media_type_internal_serdes) { + int i = 0; + adapter->hw.serdes_link_down = TRUE; + + /* On some blade server designs, link establishment + * could take as long as 2-3 minutes */ + do { + e1000_check_for_link(&adapter->hw); + if (adapter->hw.serdes_link_down == FALSE) + return *data; + msleep(20); + } while (i++ < 3750); + + *data = 1; + } else { + e1000_check_for_link(&adapter->hw); + if (adapter->hw.autoneg) /* if auto_neg is set wait for it */ + msleep(4000); + + if (!(E1000_READ_REG(&adapter->hw, STATUS) & E1000_STATUS_LU)) { + *data = 1; + } + } + return *data; +} + +static int +e1000_get_sset_count(struct net_device *netdev, int sset) +{ + switch (sset) { + case ETH_SS_TEST: + return E1000_TEST_LEN; + case ETH_SS_STATS: + return E1000_STATS_LEN; + default: + return -EOPNOTSUPP; + } +} + +static void +e1000_diag_test(struct net_device *netdev, + struct ethtool_test *eth_test, uint64_t *data) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + boolean_t if_running = netif_running(netdev); + + set_bit(__E1000_TESTING, &adapter->flags); + if (eth_test->flags == ETH_TEST_FL_OFFLINE) { + /* Offline tests */ + + /* save speed, duplex, autoneg settings */ + uint16_t autoneg_advertised = adapter->hw.autoneg_advertised; + uint8_t forced_speed_duplex = adapter->hw.forced_speed_duplex; + uint8_t autoneg = adapter->hw.autoneg; + + DPRINTK(HW, INFO, "offline testing starting\n"); + + /* Link test performed before hardware reset so autoneg doesn't + * interfere with test result */ + if (e1000_link_test(adapter, &data[4])) + eth_test->flags |= ETH_TEST_FL_FAILED; + + if (if_running) + /* indicate we're in test mode */ + dev_close(netdev); + else + e1000_reset(adapter); + + if (e1000_reg_test(adapter, &data[0])) + eth_test->flags |= ETH_TEST_FL_FAILED; + + e1000_reset(adapter); + if (e1000_eeprom_test(adapter, &data[1])) + eth_test->flags |= ETH_TEST_FL_FAILED; + + e1000_reset(adapter); + if (e1000_intr_test(adapter, &data[2])) + eth_test->flags |= ETH_TEST_FL_FAILED; + + e1000_reset(adapter); + /* make sure the phy is powered up */ + e1000_power_up_phy(adapter); + if (e1000_loopback_test(adapter, &data[3])) + eth_test->flags |= ETH_TEST_FL_FAILED; + + /* restore speed, duplex, autoneg settings */ + adapter->hw.autoneg_advertised = autoneg_advertised; + adapter->hw.forced_speed_duplex = forced_speed_duplex; + adapter->hw.autoneg = autoneg; + + e1000_reset(adapter); + clear_bit(__E1000_TESTING, &adapter->flags); + if (if_running) + dev_open(netdev); + } else { + DPRINTK(HW, INFO, "online testing starting\n"); + /* Online tests */ + if (e1000_link_test(adapter, &data[4])) + eth_test->flags |= ETH_TEST_FL_FAILED; + + /* Online tests aren't run; pass by default */ + data[0] = 0; + data[1] = 0; + data[2] = 0; + data[3] = 0; + + clear_bit(__E1000_TESTING, &adapter->flags); + } + msleep_interruptible(4 * 1000); +} + +static int e1000_wol_exclusion(struct e1000_adapter *adapter, struct ethtool_wolinfo *wol) +{ + struct e1000_hw *hw = &adapter->hw; + int retval = 1; /* fail by default */ + + switch (hw->device_id) { + case E1000_DEV_ID_82542: + case E1000_DEV_ID_82543GC_FIBER: + case E1000_DEV_ID_82543GC_COPPER: + case E1000_DEV_ID_82544EI_FIBER: + case E1000_DEV_ID_82546EB_QUAD_COPPER: + case E1000_DEV_ID_82545EM_FIBER: + case E1000_DEV_ID_82545EM_COPPER: + case E1000_DEV_ID_82546GB_QUAD_COPPER: + case E1000_DEV_ID_82546GB_PCIE: + case E1000_DEV_ID_82571EB_SERDES_QUAD: + /* these don't support WoL at all */ + wol->supported = 0; + break; + case E1000_DEV_ID_82546EB_FIBER: + case E1000_DEV_ID_82546GB_FIBER: + case E1000_DEV_ID_82571EB_FIBER: + case E1000_DEV_ID_82571EB_SERDES: + case E1000_DEV_ID_82571EB_COPPER: + /* Wake events not supported on port B */ + if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1) { + wol->supported = 0; + break; + } + /* return success for non excluded adapter ports */ + retval = 0; + break; + case E1000_DEV_ID_82571EB_QUAD_COPPER: + case E1000_DEV_ID_82571EB_QUAD_FIBER: + case E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE: + case E1000_DEV_ID_82571PT_QUAD_COPPER: + case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3: + /* quad port adapters only support WoL on port A */ + if (!adapter->quad_port_a) { + wol->supported = 0; + break; + } + /* return success for non excluded adapter ports */ + retval = 0; + break; + default: + /* dual port cards only support WoL on port A from now on + * unless it was enabled in the eeprom for port B + * so exclude FUNC_1 ports from having WoL enabled */ + if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1 && + !adapter->eeprom_wol) { + wol->supported = 0; + break; + } + + retval = 0; + } + + return retval; +} + +static void +e1000_get_wol(struct net_device *netdev, struct ethtool_wolinfo *wol) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + + wol->supported = WAKE_UCAST | WAKE_MCAST | + WAKE_BCAST | WAKE_MAGIC; + wol->wolopts = 0; + + /* this function will set ->supported = 0 and return 1 if wol is not + * supported by this hardware */ + if (e1000_wol_exclusion(adapter, wol)) + return; + + /* apply any specific unsupported masks here */ + switch (adapter->hw.device_id) { + case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3: + /* KSP3 does not suppport UCAST wake-ups */ + wol->supported &= ~WAKE_UCAST; + + if (adapter->wol & E1000_WUFC_EX) + DPRINTK(DRV, ERR, "Interface does not support " + "directed (unicast) frame wake-up packets\n"); + break; + default: + break; + } + + if (adapter->wol & E1000_WUFC_EX) + wol->wolopts |= WAKE_UCAST; + if (adapter->wol & E1000_WUFC_MC) + wol->wolopts |= WAKE_MCAST; + if (adapter->wol & E1000_WUFC_BC) + wol->wolopts |= WAKE_BCAST; + if (adapter->wol & E1000_WUFC_MAG) + wol->wolopts |= WAKE_MAGIC; + + return; +} + +static int +e1000_set_wol(struct net_device *netdev, struct ethtool_wolinfo *wol) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + struct e1000_hw *hw = &adapter->hw; + + if (wol->wolopts & (WAKE_PHY | WAKE_ARP | WAKE_MAGICSECURE)) + return -EOPNOTSUPP; + + if (e1000_wol_exclusion(adapter, wol)) + return wol->wolopts ? -EOPNOTSUPP : 0; + + switch (hw->device_id) { + case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3: + if (wol->wolopts & WAKE_UCAST) { + DPRINTK(DRV, ERR, "Interface does not support " + "directed (unicast) frame wake-up packets\n"); + return -EOPNOTSUPP; + } + break; + default: + break; + } + + /* these settings will always override what we currently have */ + adapter->wol = 0; + + if (wol->wolopts & WAKE_UCAST) + adapter->wol |= E1000_WUFC_EX; + if (wol->wolopts & WAKE_MCAST) + adapter->wol |= E1000_WUFC_MC; + if (wol->wolopts & WAKE_BCAST) + adapter->wol |= E1000_WUFC_BC; + if (wol->wolopts & WAKE_MAGIC) + adapter->wol |= E1000_WUFC_MAG; + + return 0; +} + +/* toggle LED 4 times per second = 2 "blinks" per second */ +#define E1000_ID_INTERVAL (HZ/4) + +/* bit defines for adapter->led_status */ +#define E1000_LED_ON 0 + +static void +e1000_led_blink_callback(unsigned long data) +{ + struct e1000_adapter *adapter = (struct e1000_adapter *) data; + + if (test_and_change_bit(E1000_LED_ON, &adapter->led_status)) + e1000_led_off(&adapter->hw); + else + e1000_led_on(&adapter->hw); + + mod_timer(&adapter->blink_timer, jiffies + E1000_ID_INTERVAL); +} + +static int +e1000_phys_id(struct net_device *netdev, uint32_t data) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + + if (!data) + data = INT_MAX; + + if (adapter->hw.mac_type < e1000_82571) { + if (!adapter->blink_timer.function) { + init_timer(&adapter->blink_timer); + adapter->blink_timer.function = e1000_led_blink_callback; + adapter->blink_timer.data = (unsigned long) adapter; + } + e1000_setup_led(&adapter->hw); + mod_timer(&adapter->blink_timer, jiffies); + msleep_interruptible(data * 1000); + del_timer_sync(&adapter->blink_timer); + } else if (adapter->hw.phy_type == e1000_phy_ife) { + if (!adapter->blink_timer.function) { + init_timer(&adapter->blink_timer); + adapter->blink_timer.function = e1000_led_blink_callback; + adapter->blink_timer.data = (unsigned long) adapter; + } + mod_timer(&adapter->blink_timer, jiffies); + msleep_interruptible(data * 1000); + del_timer_sync(&adapter->blink_timer); + e1000_write_phy_reg(&(adapter->hw), IFE_PHY_SPECIAL_CONTROL_LED, 0); + } else { + e1000_blink_led_start(&adapter->hw); + msleep_interruptible(data * 1000); + } + + e1000_led_off(&adapter->hw); + clear_bit(E1000_LED_ON, &adapter->led_status); + e1000_cleanup_led(&adapter->hw); + + return 0; +} + +static int +e1000_nway_reset(struct net_device *netdev) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + if (netif_running(netdev)) + e1000_reinit_locked(adapter); + return 0; +} + +static void +e1000_get_ethtool_stats(struct net_device *netdev, + struct ethtool_stats *stats, uint64_t *data) +{ + struct e1000_adapter *adapter = netdev_priv(netdev); + int i; + + e1000_update_stats(adapter); + for (i = 0; i < E1000_GLOBAL_STATS_LEN; i++) { + char *p = (char *)adapter+e1000_gstrings_stats[i].stat_offset; + data[i] = (e1000_gstrings_stats[i].sizeof_stat == + sizeof(uint64_t)) ? *(uint64_t *)p : *(uint32_t *)p; + } +/* BUG_ON(i != E1000_STATS_LEN); */ +} + +static void +e1000_get_strings(struct net_device *netdev, uint32_t stringset, uint8_t *data) +{ + uint8_t *p = data; + int i; + + switch (stringset) { + case ETH_SS_TEST: + memcpy(data, *e1000_gstrings_test, + sizeof(e1000_gstrings_test)); + break; + case ETH_SS_STATS: + for (i = 0; i < E1000_GLOBAL_STATS_LEN; i++) { + memcpy(p, e1000_gstrings_stats[i].stat_string, + ETH_GSTRING_LEN); + p += ETH_GSTRING_LEN; + } +/* BUG_ON(p - data != E1000_STATS_LEN * ETH_GSTRING_LEN); */ + break; + } +} + +static const struct ethtool_ops e1000_ethtool_ops = { + .get_settings = e1000_get_settings, + .set_settings = e1000_set_settings, + .get_drvinfo = e1000_get_drvinfo, + .get_regs_len = e1000_get_regs_len, + .get_regs = e1000_get_regs, + .get_wol = e1000_get_wol, + .set_wol = e1000_set_wol, + .get_msglevel = e1000_get_msglevel, + .set_msglevel = e1000_set_msglevel, + .nway_reset = e1000_nway_reset, + .get_link = ethtool_op_get_link, + .get_eeprom_len = e1000_get_eeprom_len, + .get_eeprom = e1000_get_eeprom, + .set_eeprom = e1000_set_eeprom, + .get_ringparam = e1000_get_ringparam, + .set_ringparam = e1000_set_ringparam, + .get_pauseparam = e1000_get_pauseparam, + .set_pauseparam = e1000_set_pauseparam, + .get_rx_csum = e1000_get_rx_csum, + .set_rx_csum = e1000_set_rx_csum, + .get_tx_csum = e1000_get_tx_csum, + .set_tx_csum = e1000_set_tx_csum, + .set_sg = ethtool_op_set_sg, + .set_tso = e1000_set_tso, + .self_test = e1000_diag_test, + .get_strings = e1000_get_strings, + .phys_id = e1000_phys_id, + .get_ethtool_stats = e1000_get_ethtool_stats, + .get_sset_count = e1000_get_sset_count, +}; + +void e1000_set_ethtool_ops(struct net_device *netdev) +{ + SET_ETHTOOL_OPS(netdev, &e1000_ethtool_ops); +} diff -Nur ethercat-1.4.0/devices/e1000/e1000_hw-2.6.32-ethercat.c ethercat-1.4.0.patched//devices/e1000/e1000_hw-2.6.32-ethercat.c --- ethercat-1.4.0/devices/e1000/e1000_hw-2.6.32-ethercat.c 1970-01-01 01:00:00.000000000 +0100 +++ ethercat-1.4.0.patched//devices/e1000/e1000_hw-2.6.32-ethercat.c 2011-11-18 12:19:07.298574480 +0100 @@ -0,0 +1,9025 @@ +/******************************************************************************* + + Intel PRO/1000 Linux driver + Copyright(c) 1999 - 2006 Intel Corporation. + + This program is free software; you can redistribute it and/or modify it + under the terms and conditions of the GNU General Public License, + version 2, as published by the Free Software Foundation. + + This program is distributed in the hope it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., + 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. + + The full GNU General Public License is included in this distribution in + the file called "COPYING". + + Contact Information: + Linux NICS + e1000-devel Mailing List + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + +*******************************************************************************/ + +/* e1000_hw.c + * Shared functions for accessing and configuring the MAC + */ + + +#include "e1000_hw-2.6.24-ethercat.h" + +static int32_t e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask); +static void e1000_swfw_sync_release(struct e1000_hw *hw, uint16_t mask); +static int32_t e1000_read_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t *data); +static int32_t e1000_write_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t data); +static int32_t e1000_get_software_semaphore(struct e1000_hw *hw); +static void e1000_release_software_semaphore(struct e1000_hw *hw); + +static uint8_t e1000_arc_subsystem_valid(struct e1000_hw *hw); +static int32_t e1000_check_downshift(struct e1000_hw *hw); +static int32_t e1000_check_polarity(struct e1000_hw *hw, e1000_rev_polarity *polarity); +static void e1000_clear_hw_cntrs(struct e1000_hw *hw); +static void e1000_clear_vfta(struct e1000_hw *hw); +static int32_t e1000_commit_shadow_ram(struct e1000_hw *hw); +static int32_t e1000_config_dsp_after_link_change(struct e1000_hw *hw, boolean_t link_up); +static int32_t e1000_config_fc_after_link_up(struct e1000_hw *hw); +static int32_t e1000_detect_gig_phy(struct e1000_hw *hw); +static int32_t e1000_erase_ich8_4k_segment(struct e1000_hw *hw, uint32_t bank); +static int32_t e1000_get_auto_rd_done(struct e1000_hw *hw); +static int32_t e1000_get_cable_length(struct e1000_hw *hw, uint16_t *min_length, uint16_t *max_length); +static int32_t e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw); +static int32_t e1000_get_phy_cfg_done(struct e1000_hw *hw); +static int32_t e1000_get_software_flag(struct e1000_hw *hw); +static int32_t e1000_ich8_cycle_init(struct e1000_hw *hw); +static int32_t e1000_ich8_flash_cycle(struct e1000_hw *hw, uint32_t timeout); +static int32_t e1000_id_led_init(struct e1000_hw *hw); +static int32_t e1000_init_lcd_from_nvm_config_region(struct e1000_hw *hw, uint32_t cnf_base_addr, uint32_t cnf_size); +static int32_t e1000_init_lcd_from_nvm(struct e1000_hw *hw); +static void e1000_init_rx_addrs(struct e1000_hw *hw); +static void e1000_initialize_hardware_bits(struct e1000_hw *hw); +static boolean_t e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw); +static int32_t e1000_kumeran_lock_loss_workaround(struct e1000_hw *hw); +static int32_t e1000_mng_enable_host_if(struct e1000_hw *hw); +static int32_t e1000_mng_host_if_write(struct e1000_hw *hw, uint8_t *buffer, uint16_t length, uint16_t offset, uint8_t *sum); +static int32_t e1000_mng_write_cmd_header(struct e1000_hw* hw, struct e1000_host_mng_command_header* hdr); +static int32_t e1000_mng_write_commit(struct e1000_hw *hw); +static int32_t e1000_phy_ife_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info); +static int32_t e1000_phy_igp_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info); +static int32_t e1000_read_eeprom_eerd(struct e1000_hw *hw, uint16_t offset, uint16_t words, uint16_t *data); +static int32_t e1000_write_eeprom_eewr(struct e1000_hw *hw, uint16_t offset, uint16_t words, uint16_t *data); +static int32_t e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd); +static int32_t e1000_phy_m88_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info); +static void e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw); +static int32_t e1000_read_ich8_byte(struct e1000_hw *hw, uint32_t index, uint8_t *data); +static int32_t e1000_verify_write_ich8_byte(struct e1000_hw *hw, uint32_t index, uint8_t byte); +static int32_t e1000_write_ich8_byte(struct e1000_hw *hw, uint32_t index, uint8_t byte); +static int32_t e1000_read_ich8_word(struct e1000_hw *hw, uint32_t index, uint16_t *data); +static int32_t e1000_read_ich8_data(struct e1000_hw *hw, uint32_t index, uint32_t size, uint16_t *data); +static int32_t e1000_write_ich8_data(struct e1000_hw *hw, uint32_t index, uint32_t size, uint16_t data); +static int32_t e1000_read_eeprom_ich8(struct e1000_hw *hw, uint16_t offset, uint16_t words, uint16_t *data); +static int32_t e1000_write_eeprom_ich8(struct e1000_hw *hw, uint16_t offset, uint16_t words, uint16_t *data); +static void e1000_release_software_flag(struct e1000_hw *hw); +static int32_t e1000_set_d3_lplu_state(struct e1000_hw *hw, boolean_t active); +static int32_t e1000_set_d0_lplu_state(struct e1000_hw *hw, boolean_t active); +static int32_t e1000_set_pci_ex_no_snoop(struct e1000_hw *hw, uint32_t no_snoop); +static void e1000_set_pci_express_master_disable(struct e1000_hw *hw); +static int32_t e1000_wait_autoneg(struct e1000_hw *hw); +static void e1000_write_reg_io(struct e1000_hw *hw, uint32_t offset, uint32_t value); +static int32_t e1000_set_phy_type(struct e1000_hw *hw); +static void e1000_phy_init_script(struct e1000_hw *hw); +static int32_t e1000_setup_copper_link(struct e1000_hw *hw); +static int32_t e1000_setup_fiber_serdes_link(struct e1000_hw *hw); +static int32_t e1000_adjust_serdes_amplitude(struct e1000_hw *hw); +static int32_t e1000_phy_force_speed_duplex(struct e1000_hw *hw); +static int32_t e1000_config_mac_to_phy(struct e1000_hw *hw); +static void e1000_raise_mdi_clk(struct e1000_hw *hw, uint32_t *ctrl); +static void e1000_lower_mdi_clk(struct e1000_hw *hw, uint32_t *ctrl); +static void e1000_shift_out_mdi_bits(struct e1000_hw *hw, uint32_t data, + uint16_t count); +static uint16_t e1000_shift_in_mdi_bits(struct e1000_hw *hw); +static int32_t e1000_phy_reset_dsp(struct e1000_hw *hw); +static int32_t e1000_write_eeprom_spi(struct e1000_hw *hw, uint16_t offset, + uint16_t words, uint16_t *data); +static int32_t e1000_write_eeprom_microwire(struct e1000_hw *hw, + uint16_t offset, uint16_t words, + uint16_t *data); +static int32_t e1000_spi_eeprom_ready(struct e1000_hw *hw); +static void e1000_raise_ee_clk(struct e1000_hw *hw, uint32_t *eecd); +static void e1000_lower_ee_clk(struct e1000_hw *hw, uint32_t *eecd); +static void e1000_shift_out_ee_bits(struct e1000_hw *hw, uint16_t data, + uint16_t count); +static int32_t e1000_write_phy_reg_ex(struct e1000_hw *hw, uint32_t reg_addr, + uint16_t phy_data); +static int32_t e1000_read_phy_reg_ex(struct e1000_hw *hw,uint32_t reg_addr, + uint16_t *phy_data); +static uint16_t e1000_shift_in_ee_bits(struct e1000_hw *hw, uint16_t count); +static int32_t e1000_acquire_eeprom(struct e1000_hw *hw); +static void e1000_release_eeprom(struct e1000_hw *hw); +static void e1000_standby_eeprom(struct e1000_hw *hw); +static int32_t e1000_set_vco_speed(struct e1000_hw *hw); +static int32_t e1000_polarity_reversal_workaround(struct e1000_hw *hw); +static int32_t e1000_set_phy_mode(struct e1000_hw *hw); +static int32_t e1000_host_if_read_cookie(struct e1000_hw *hw, uint8_t *buffer); +static uint8_t e1000_calculate_mng_checksum(char *buffer, uint32_t length); +static int32_t e1000_configure_kmrn_for_10_100(struct e1000_hw *hw, + uint16_t duplex); +static int32_t e1000_configure_kmrn_for_1000(struct e1000_hw *hw); + +/* IGP cable length table */ +static const +uint16_t e1000_igp_cable_length_table[IGP01E1000_AGC_LENGTH_TABLE_SIZE] = + { 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, + 5, 10, 10, 10, 10, 10, 10, 10, 20, 20, 20, 20, 20, 25, 25, 25, + 25, 25, 25, 25, 30, 30, 30, 30, 40, 40, 40, 40, 40, 40, 40, 40, + 40, 50, 50, 50, 50, 50, 50, 50, 60, 60, 60, 60, 60, 60, 60, 60, + 60, 70, 70, 70, 70, 70, 70, 80, 80, 80, 80, 80, 80, 90, 90, 90, + 90, 90, 90, 90, 90, 90, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, + 100, 100, 100, 100, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, + 110, 110, 110, 110, 110, 110, 120, 120, 120, 120, 120, 120, 120, 120, 120, 120}; + +static const +uint16_t e1000_igp_2_cable_length_table[IGP02E1000_AGC_LENGTH_TABLE_SIZE] = + { 0, 0, 0, 0, 0, 0, 0, 0, 3, 5, 8, 11, 13, 16, 18, 21, + 0, 0, 0, 3, 6, 10, 13, 16, 19, 23, 26, 29, 32, 35, 38, 41, + 6, 10, 14, 18, 22, 26, 30, 33, 37, 41, 44, 48, 51, 54, 58, 61, + 21, 26, 31, 35, 40, 44, 49, 53, 57, 61, 65, 68, 72, 75, 79, 82, + 40, 45, 51, 56, 61, 66, 70, 75, 79, 83, 87, 91, 94, 98, 101, 104, + 60, 66, 72, 77, 82, 87, 92, 96, 100, 104, 108, 111, 114, 117, 119, 121, + 83, 89, 95, 100, 105, 109, 113, 116, 119, 122, 124, + 104, 109, 114, 118, 121, 124}; + +/****************************************************************************** + * Set the phy type member in the hw struct. + * + * hw - Struct containing variables accessed by shared code + *****************************************************************************/ +static int32_t +e1000_set_phy_type(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_set_phy_type"); + + if (hw->mac_type == e1000_undefined) + return -E1000_ERR_PHY_TYPE; + + switch (hw->phy_id) { + case M88E1000_E_PHY_ID: + case M88E1000_I_PHY_ID: + case M88E1011_I_PHY_ID: + case M88E1111_I_PHY_ID: + hw->phy_type = e1000_phy_m88; + break; + case IGP01E1000_I_PHY_ID: + if (hw->mac_type == e1000_82541 || + hw->mac_type == e1000_82541_rev_2 || + hw->mac_type == e1000_82547 || + hw->mac_type == e1000_82547_rev_2) { + hw->phy_type = e1000_phy_igp; + break; + } + case IGP03E1000_E_PHY_ID: + hw->phy_type = e1000_phy_igp_3; + break; + case IFE_E_PHY_ID: + case IFE_PLUS_E_PHY_ID: + case IFE_C_E_PHY_ID: + hw->phy_type = e1000_phy_ife; + break; + case GG82563_E_PHY_ID: + if (hw->mac_type == e1000_80003es2lan) { + hw->phy_type = e1000_phy_gg82563; + break; + } + /* Fall Through */ + default: + /* Should never have loaded on this device */ + hw->phy_type = e1000_phy_undefined; + return -E1000_ERR_PHY_TYPE; + } + + return E1000_SUCCESS; +} + +/****************************************************************************** + * IGP phy init script - initializes the GbE PHY + * + * hw - Struct containing variables accessed by shared code + *****************************************************************************/ +static void +e1000_phy_init_script(struct e1000_hw *hw) +{ + uint32_t ret_val; + uint16_t phy_saved_data; + + DEBUGFUNC("e1000_phy_init_script"); + + if (hw->phy_init_script) { + msleep(20); + + /* Save off the current value of register 0x2F5B to be restored at + * the end of this routine. */ + ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data); + + /* Disabled the PHY transmitter */ + e1000_write_phy_reg(hw, 0x2F5B, 0x0003); + + msleep(20); + + e1000_write_phy_reg(hw,0x0000,0x0140); + + msleep(5); + + switch (hw->mac_type) { + case e1000_82541: + case e1000_82547: + e1000_write_phy_reg(hw, 0x1F95, 0x0001); + + e1000_write_phy_reg(hw, 0x1F71, 0xBD21); + + e1000_write_phy_reg(hw, 0x1F79, 0x0018); + + e1000_write_phy_reg(hw, 0x1F30, 0x1600); + + e1000_write_phy_reg(hw, 0x1F31, 0x0014); + + e1000_write_phy_reg(hw, 0x1F32, 0x161C); + + e1000_write_phy_reg(hw, 0x1F94, 0x0003); + + e1000_write_phy_reg(hw, 0x1F96, 0x003F); + + e1000_write_phy_reg(hw, 0x2010, 0x0008); + break; + + case e1000_82541_rev_2: + case e1000_82547_rev_2: + e1000_write_phy_reg(hw, 0x1F73, 0x0099); + break; + default: + break; + } + + e1000_write_phy_reg(hw, 0x0000, 0x3300); + + msleep(20); + + /* Now enable the transmitter */ + e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data); + + if (hw->mac_type == e1000_82547) { + uint16_t fused, fine, coarse; + + /* Move to analog registers page */ + e1000_read_phy_reg(hw, IGP01E1000_ANALOG_SPARE_FUSE_STATUS, &fused); + + if (!(fused & IGP01E1000_ANALOG_SPARE_FUSE_ENABLED)) { + e1000_read_phy_reg(hw, IGP01E1000_ANALOG_FUSE_STATUS, &fused); + + fine = fused & IGP01E1000_ANALOG_FUSE_FINE_MASK; + coarse = fused & IGP01E1000_ANALOG_FUSE_COARSE_MASK; + + if (coarse > IGP01E1000_ANALOG_FUSE_COARSE_THRESH) { + coarse -= IGP01E1000_ANALOG_FUSE_COARSE_10; + fine -= IGP01E1000_ANALOG_FUSE_FINE_1; + } else if (coarse == IGP01E1000_ANALOG_FUSE_COARSE_THRESH) + fine -= IGP01E1000_ANALOG_FUSE_FINE_10; + + fused = (fused & IGP01E1000_ANALOG_FUSE_POLY_MASK) | + (fine & IGP01E1000_ANALOG_FUSE_FINE_MASK) | + (coarse & IGP01E1000_ANALOG_FUSE_COARSE_MASK); + + e1000_write_phy_reg(hw, IGP01E1000_ANALOG_FUSE_CONTROL, fused); + e1000_write_phy_reg(hw, IGP01E1000_ANALOG_FUSE_BYPASS, + IGP01E1000_ANALOG_FUSE_ENABLE_SW_CONTROL); + } + } + } +} + +/****************************************************************************** + * Set the mac type member in the hw struct. + * + * hw - Struct containing variables accessed by shared code + *****************************************************************************/ +int32_t +e1000_set_mac_type(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_set_mac_type"); + + switch (hw->device_id) { + case E1000_DEV_ID_82542: + switch (hw->revision_id) { + case E1000_82542_2_0_REV_ID: + hw->mac_type = e1000_82542_rev2_0; + break; + case E1000_82542_2_1_REV_ID: + hw->mac_type = e1000_82542_rev2_1; + break; + default: + /* Invalid 82542 revision ID */ + return -E1000_ERR_MAC_TYPE; + } + break; + case E1000_DEV_ID_82543GC_FIBER: + case E1000_DEV_ID_82543GC_COPPER: + hw->mac_type = e1000_82543; + break; + case E1000_DEV_ID_82544EI_COPPER: + case E1000_DEV_ID_82544EI_FIBER: + case E1000_DEV_ID_82544GC_COPPER: + case E1000_DEV_ID_82544GC_LOM: + hw->mac_type = e1000_82544; + break; + case E1000_DEV_ID_82540EM: + case E1000_DEV_ID_82540EM_LOM: + case E1000_DEV_ID_82540EP: + case E1000_DEV_ID_82540EP_LOM: + case E1000_DEV_ID_82540EP_LP: + hw->mac_type = e1000_82540; + break; + case E1000_DEV_ID_82545EM_COPPER: + case E1000_DEV_ID_82545EM_FIBER: + hw->mac_type = e1000_82545; + break; + case E1000_DEV_ID_82545GM_COPPER: + case E1000_DEV_ID_82545GM_FIBER: + case E1000_DEV_ID_82545GM_SERDES: + hw->mac_type = e1000_82545_rev_3; + break; + case E1000_DEV_ID_82546EB_COPPER: + case E1000_DEV_ID_82546EB_FIBER: + case E1000_DEV_ID_82546EB_QUAD_COPPER: + hw->mac_type = e1000_82546; + break; + case E1000_DEV_ID_82546GB_COPPER: + case E1000_DEV_ID_82546GB_FIBER: + case E1000_DEV_ID_82546GB_SERDES: + case E1000_DEV_ID_82546GB_PCIE: + case E1000_DEV_ID_82546GB_QUAD_COPPER: + case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3: + hw->mac_type = e1000_82546_rev_3; + break; + case E1000_DEV_ID_82541EI: + case E1000_DEV_ID_82541EI_MOBILE: + case E1000_DEV_ID_82541ER_LOM: + hw->mac_type = e1000_82541; + break; + case E1000_DEV_ID_82541ER: + case E1000_DEV_ID_82541GI: + case E1000_DEV_ID_82541GI_LF: + case E1000_DEV_ID_82541GI_MOBILE: + hw->mac_type = e1000_82541_rev_2; + break; + case E1000_DEV_ID_82547EI: + case E1000_DEV_ID_82547EI_MOBILE: + hw->mac_type = e1000_82547; + break; + case E1000_DEV_ID_82547GI: + hw->mac_type = e1000_82547_rev_2; + break; + case E1000_DEV_ID_82571EB_COPPER: + case E1000_DEV_ID_82571EB_FIBER: + case E1000_DEV_ID_82571EB_SERDES: + case E1000_DEV_ID_82571EB_SERDES_DUAL: + case E1000_DEV_ID_82571EB_SERDES_QUAD: + case E1000_DEV_ID_82571EB_QUAD_COPPER: + case E1000_DEV_ID_82571PT_QUAD_COPPER: + case E1000_DEV_ID_82571EB_QUAD_FIBER: + case E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE: + hw->mac_type = e1000_82571; + break; + case E1000_DEV_ID_82572EI_COPPER: + case E1000_DEV_ID_82572EI_FIBER: + case E1000_DEV_ID_82572EI_SERDES: + case E1000_DEV_ID_82572EI: + hw->mac_type = e1000_82572; + break; + case E1000_DEV_ID_82573E: + case E1000_DEV_ID_82573E_IAMT: + case E1000_DEV_ID_82573L: + hw->mac_type = e1000_82573; + break; + case E1000_DEV_ID_80003ES2LAN_COPPER_SPT: + case E1000_DEV_ID_80003ES2LAN_SERDES_SPT: + case E1000_DEV_ID_80003ES2LAN_COPPER_DPT: + case E1000_DEV_ID_80003ES2LAN_SERDES_DPT: + hw->mac_type = e1000_80003es2lan; + break; + case E1000_DEV_ID_ICH8_IGP_M_AMT: + case E1000_DEV_ID_ICH8_IGP_AMT: + case E1000_DEV_ID_ICH8_IGP_C: + case E1000_DEV_ID_ICH8_IFE: + case E1000_DEV_ID_ICH8_IFE_GT: + case E1000_DEV_ID_ICH8_IFE_G: + case E1000_DEV_ID_ICH8_IGP_M: + hw->mac_type = e1000_ich8lan; + break; + default: + /* Should never have loaded on this device */ + return -E1000_ERR_MAC_TYPE; + } + + switch (hw->mac_type) { + case e1000_ich8lan: + hw->swfwhw_semaphore_present = TRUE; + hw->asf_firmware_present = TRUE; + break; + case e1000_80003es2lan: + hw->swfw_sync_present = TRUE; + /* fall through */ + case e1000_82571: + case e1000_82572: + case e1000_82573: + hw->eeprom_semaphore_present = TRUE; + /* fall through */ + case e1000_82541: + case e1000_82547: + case e1000_82541_rev_2: + case e1000_82547_rev_2: + hw->asf_firmware_present = TRUE; + break; + default: + break; + } + + /* The 82543 chip does not count tx_carrier_errors properly in + * FD mode + */ + if (hw->mac_type == e1000_82543) + hw->bad_tx_carr_stats_fd = TRUE; + + /* capable of receiving management packets to the host */ + if (hw->mac_type >= e1000_82571) + hw->has_manc2h = TRUE; + + /* In rare occasions, ESB2 systems would end up started without + * the RX unit being turned on. + */ + if (hw->mac_type == e1000_80003es2lan) + hw->rx_needs_kicking = TRUE; + + if (hw->mac_type > e1000_82544) + hw->has_smbus = TRUE; + + return E1000_SUCCESS; +} + +/***************************************************************************** + * Set media type and TBI compatibility. + * + * hw - Struct containing variables accessed by shared code + * **************************************************************************/ +void +e1000_set_media_type(struct e1000_hw *hw) +{ + uint32_t status; + + DEBUGFUNC("e1000_set_media_type"); + + if (hw->mac_type != e1000_82543) { + /* tbi_compatibility is only valid on 82543 */ + hw->tbi_compatibility_en = FALSE; + } + + switch (hw->device_id) { + case E1000_DEV_ID_82545GM_SERDES: + case E1000_DEV_ID_82546GB_SERDES: + case E1000_DEV_ID_82571EB_SERDES: + case E1000_DEV_ID_82571EB_SERDES_DUAL: + case E1000_DEV_ID_82571EB_SERDES_QUAD: + case E1000_DEV_ID_82572EI_SERDES: + case E1000_DEV_ID_80003ES2LAN_SERDES_DPT: + hw->media_type = e1000_media_type_internal_serdes; + break; + default: + switch (hw->mac_type) { + case e1000_82542_rev2_0: + case e1000_82542_rev2_1: + hw->media_type = e1000_media_type_fiber; + break; + case e1000_ich8lan: + case e1000_82573: + /* The STATUS_TBIMODE bit is reserved or reused for the this + * device. + */ + hw->media_type = e1000_media_type_copper; + break; + default: + status = E1000_READ_REG(hw, STATUS); + if (status & E1000_STATUS_TBIMODE) { + hw->media_type = e1000_media_type_fiber; + /* tbi_compatibility not valid on fiber */ + hw->tbi_compatibility_en = FALSE; + } else { + hw->media_type = e1000_media_type_copper; + } + break; + } + } +} + +/****************************************************************************** + * Reset the transmit and receive units; mask and clear all interrupts. + * + * hw - Struct containing variables accessed by shared code + *****************************************************************************/ +int32_t +e1000_reset_hw(struct e1000_hw *hw) +{ + uint32_t ctrl; + uint32_t ctrl_ext; + uint32_t icr; + uint32_t manc; + uint32_t led_ctrl; + uint32_t timeout; + uint32_t extcnf_ctrl; + int32_t ret_val; + + DEBUGFUNC("e1000_reset_hw"); + + /* For 82542 (rev 2.0), disable MWI before issuing a device reset */ + if (hw->mac_type == e1000_82542_rev2_0) { + DEBUGOUT("Disabling MWI on 82542 rev 2.0\n"); + e1000_pci_clear_mwi(hw); + } + + if (hw->bus_type == e1000_bus_type_pci_express) { + /* Prevent the PCI-E bus from sticking if there is no TLP connection + * on the last TLP read/write transaction when MAC is reset. + */ + if (e1000_disable_pciex_master(hw) != E1000_SUCCESS) { + DEBUGOUT("PCI-E Master disable polling has failed.\n"); + } + } + + /* Clear interrupt mask to stop board from generating interrupts */ + DEBUGOUT("Masking off all interrupts\n"); + E1000_WRITE_REG(hw, IMC, 0xffffffff); + + /* Disable the Transmit and Receive units. Then delay to allow + * any pending transactions to complete before we hit the MAC with + * the global reset. + */ + E1000_WRITE_REG(hw, RCTL, 0); + E1000_WRITE_REG(hw, TCTL, E1000_TCTL_PSP); + E1000_WRITE_FLUSH(hw); + + /* The tbi_compatibility_on Flag must be cleared when Rctl is cleared. */ + hw->tbi_compatibility_on = FALSE; + + /* Delay to allow any outstanding PCI transactions to complete before + * resetting the device + */ + msleep(10); + + ctrl = E1000_READ_REG(hw, CTRL); + + /* Must reset the PHY before resetting the MAC */ + if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) { + E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_PHY_RST)); + msleep(5); + } + + /* Must acquire the MDIO ownership before MAC reset. + * Ownership defaults to firmware after a reset. */ + if (hw->mac_type == e1000_82573) { + timeout = 10; + + extcnf_ctrl = E1000_READ_REG(hw, EXTCNF_CTRL); + extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP; + + do { + E1000_WRITE_REG(hw, EXTCNF_CTRL, extcnf_ctrl); + extcnf_ctrl = E1000_READ_REG(hw, EXTCNF_CTRL); + + if (extcnf_ctrl & E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP) + break; + else + extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP; + + msleep(2); + timeout--; + } while (timeout); + } + + /* Workaround for ICH8 bit corruption issue in FIFO memory */ + if (hw->mac_type == e1000_ich8lan) { + /* Set Tx and Rx buffer allocation to 8k apiece. */ + E1000_WRITE_REG(hw, PBA, E1000_PBA_8K); + /* Set Packet Buffer Size to 16k. */ + E1000_WRITE_REG(hw, PBS, E1000_PBS_16K); + } + + /* Issue a global reset to the MAC. This will reset the chip's + * transmit, receive, DMA, and link units. It will not effect + * the current PCI configuration. The global reset bit is self- + * clearing, and should clear within a microsecond. + */ + DEBUGOUT("Issuing a global reset to MAC\n"); + + switch (hw->mac_type) { + case e1000_82544: + case e1000_82540: + case e1000_82545: + case e1000_82546: + case e1000_82541: + case e1000_82541_rev_2: + /* These controllers can't ack the 64-bit write when issuing the + * reset, so use IO-mapping as a workaround to issue the reset */ + E1000_WRITE_REG_IO(hw, CTRL, (ctrl | E1000_CTRL_RST)); + break; + case e1000_82545_rev_3: + case e1000_82546_rev_3: + /* Reset is performed on a shadow of the control register */ + E1000_WRITE_REG(hw, CTRL_DUP, (ctrl | E1000_CTRL_RST)); + break; + case e1000_ich8lan: + if (!hw->phy_reset_disable && + e1000_check_phy_reset_block(hw) == E1000_SUCCESS) { + /* e1000_ich8lan PHY HW reset requires MAC CORE reset + * at the same time to make sure the interface between + * MAC and the external PHY is reset. + */ + ctrl |= E1000_CTRL_PHY_RST; + } + + e1000_get_software_flag(hw); + E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_RST)); + msleep(5); + break; + default: + E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_RST)); + break; + } + + /* After MAC reset, force reload of EEPROM to restore power-on settings to + * device. Later controllers reload the EEPROM automatically, so just wait + * for reload to complete. + */ + switch (hw->mac_type) { + case e1000_82542_rev2_0: + case e1000_82542_rev2_1: + case e1000_82543: + case e1000_82544: + /* Wait for reset to complete */ + udelay(10); + ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); + ctrl_ext |= E1000_CTRL_EXT_EE_RST; + E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); + E1000_WRITE_FLUSH(hw); + /* Wait for EEPROM reload */ + msleep(2); + break; + case e1000_82541: + case e1000_82541_rev_2: + case e1000_82547: + case e1000_82547_rev_2: + /* Wait for EEPROM reload */ + msleep(20); + break; + case e1000_82573: + if (e1000_is_onboard_nvm_eeprom(hw) == FALSE) { + udelay(10); + ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); + ctrl_ext |= E1000_CTRL_EXT_EE_RST; + E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); + E1000_WRITE_FLUSH(hw); + } + /* fall through */ + default: + /* Auto read done will delay 5ms or poll based on mac type */ + ret_val = e1000_get_auto_rd_done(hw); + if (ret_val) + return ret_val; + break; + } + + /* Disable HW ARPs on ASF enabled adapters */ + if (hw->mac_type >= e1000_82540 && hw->mac_type <= e1000_82547_rev_2) { + manc = E1000_READ_REG(hw, MANC); + manc &= ~(E1000_MANC_ARP_EN); + E1000_WRITE_REG(hw, MANC, manc); + } + + if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) { + e1000_phy_init_script(hw); + + /* Configure activity LED after PHY reset */ + led_ctrl = E1000_READ_REG(hw, LEDCTL); + led_ctrl &= IGP_ACTIVITY_LED_MASK; + led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); + E1000_WRITE_REG(hw, LEDCTL, led_ctrl); + } + + /* Clear interrupt mask to stop board from generating interrupts */ + DEBUGOUT("Masking off all interrupts\n"); + E1000_WRITE_REG(hw, IMC, 0xffffffff); + + /* Clear any pending interrupt events. */ + icr = E1000_READ_REG(hw, ICR); + + /* If MWI was previously enabled, reenable it. */ + if (hw->mac_type == e1000_82542_rev2_0) { + if (hw->pci_cmd_word & PCI_COMMAND_INVALIDATE) + e1000_pci_set_mwi(hw); + } + + if (hw->mac_type == e1000_ich8lan) { + uint32_t kab = E1000_READ_REG(hw, KABGTXD); + kab |= E1000_KABGTXD_BGSQLBIAS; + E1000_WRITE_REG(hw, KABGTXD, kab); + } + + return E1000_SUCCESS; +} + +/****************************************************************************** + * + * Initialize a number of hardware-dependent bits + * + * hw: Struct containing variables accessed by shared code + * + * This function contains hardware limitation workarounds for PCI-E adapters + * + *****************************************************************************/ +static void +e1000_initialize_hardware_bits(struct e1000_hw *hw) +{ + if ((hw->mac_type >= e1000_82571) && (!hw->initialize_hw_bits_disable)) { + /* Settings common to all PCI-express silicon */ + uint32_t reg_ctrl, reg_ctrl_ext; + uint32_t reg_tarc0, reg_tarc1; + uint32_t reg_tctl; + uint32_t reg_txdctl, reg_txdctl1; + + /* link autonegotiation/sync workarounds */ + reg_tarc0 = E1000_READ_REG(hw, TARC0); + reg_tarc0 &= ~((1 << 30)|(1 << 29)|(1 << 28)|(1 << 27)); + + /* Enable not-done TX descriptor counting */ + reg_txdctl = E1000_READ_REG(hw, TXDCTL); + reg_txdctl |= E1000_TXDCTL_COUNT_DESC; + E1000_WRITE_REG(hw, TXDCTL, reg_txdctl); + reg_txdctl1 = E1000_READ_REG(hw, TXDCTL1); + reg_txdctl1 |= E1000_TXDCTL_COUNT_DESC; + E1000_WRITE_REG(hw, TXDCTL1, reg_txdctl1); + + switch (hw->mac_type) { + case e1000_82571: + case e1000_82572: + /* Clear PHY TX compatible mode bits */ + reg_tarc1 = E1000_READ_REG(hw, TARC1); + reg_tarc1 &= ~((1 << 30)|(1 << 29)); + + /* link autonegotiation/sync workarounds */ + reg_tarc0 |= ((1 << 26)|(1 << 25)|(1 << 24)|(1 << 23)); + + /* TX ring control fixes */ + reg_tarc1 |= ((1 << 26)|(1 << 25)|(1 << 24)); + + /* Multiple read bit is reversed polarity */ + reg_tctl = E1000_READ_REG(hw, TCTL); + if (reg_tctl & E1000_TCTL_MULR) + reg_tarc1 &= ~(1 << 28); + else + reg_tarc1 |= (1 << 28); + + E1000_WRITE_REG(hw, TARC1, reg_tarc1); + break; + case e1000_82573: + reg_ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); + reg_ctrl_ext &= ~(1 << 23); + reg_ctrl_ext |= (1 << 22); + + /* TX byte count fix */ + reg_ctrl = E1000_READ_REG(hw, CTRL); + reg_ctrl &= ~(1 << 29); + + E1000_WRITE_REG(hw, CTRL_EXT, reg_ctrl_ext); + E1000_WRITE_REG(hw, CTRL, reg_ctrl); + break; + case e1000_80003es2lan: + /* improve small packet performace for fiber/serdes */ + if ((hw->media_type == e1000_media_type_fiber) || + (hw->media_type == e1000_media_type_internal_serdes)) { + reg_tarc0 &= ~(1 << 20); + } + + /* Multiple read bit is reversed polarity */ + reg_tctl = E1000_READ_REG(hw, TCTL); + reg_tarc1 = E1000_READ_REG(hw, TARC1); + if (reg_tctl & E1000_TCTL_MULR) + reg_tarc1 &= ~(1 << 28); + else + reg_tarc1 |= (1 << 28); + + E1000_WRITE_REG(hw, TARC1, reg_tarc1); + break; + case e1000_ich8lan: + /* Reduce concurrent DMA requests to 3 from 4 */ + if ((hw->revision_id < 3) || + ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) && + (hw->device_id != E1000_DEV_ID_ICH8_IGP_M))) + reg_tarc0 |= ((1 << 29)|(1 << 28)); + + reg_ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); + reg_ctrl_ext |= (1 << 22); + E1000_WRITE_REG(hw, CTRL_EXT, reg_ctrl_ext); + + /* workaround TX hang with TSO=on */ + reg_tarc0 |= ((1 << 27)|(1 << 26)|(1 << 24)|(1 << 23)); + + /* Multiple read bit is reversed polarity */ + reg_tctl = E1000_READ_REG(hw, TCTL); + reg_tarc1 = E1000_READ_REG(hw, TARC1); + if (reg_tctl & E1000_TCTL_MULR) + reg_tarc1 &= ~(1 << 28); + else + reg_tarc1 |= (1 << 28); + + /* workaround TX hang with TSO=on */ + reg_tarc1 |= ((1 << 30)|(1 << 26)|(1 << 24)); + + E1000_WRITE_REG(hw, TARC1, reg_tarc1); + break; + default: + break; + } + + E1000_WRITE_REG(hw, TARC0, reg_tarc0); + } +} + +/****************************************************************************** + * Performs basic configuration of the adapter. + * + * hw - Struct containing variables accessed by shared code + * + * Assumes that the controller has previously been reset and is in a + * post-reset uninitialized state. Initializes the receive address registers, + * multicast table, and VLAN filter table. Calls routines to setup link + * configuration and flow control settings. Clears all on-chip counters. Leaves + * the transmit and receive units disabled and uninitialized. + *****************************************************************************/ +int32_t +e1000_init_hw(struct e1000_hw *hw) +{ + uint32_t ctrl; + uint32_t i; + int32_t ret_val; + uint32_t mta_size; + uint32_t reg_data; + uint32_t ctrl_ext; + + DEBUGFUNC("e1000_init_hw"); + + /* force full DMA clock frequency for 10/100 on ICH8 A0-B0 */ + if ((hw->mac_type == e1000_ich8lan) && + ((hw->revision_id < 3) || + ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) && + (hw->device_id != E1000_DEV_ID_ICH8_IGP_M)))) { + reg_data = E1000_READ_REG(hw, STATUS); + reg_data &= ~0x80000000; + E1000_WRITE_REG(hw, STATUS, reg_data); + } + + /* Initialize Identification LED */ + ret_val = e1000_id_led_init(hw); + if (ret_val) { + DEBUGOUT("Error Initializing Identification LED\n"); + return ret_val; + } + + /* Set the media type and TBI compatibility */ + e1000_set_media_type(hw); + + /* Must be called after e1000_set_media_type because media_type is used */ + e1000_initialize_hardware_bits(hw); + + /* Disabling VLAN filtering. */ + DEBUGOUT("Initializing the IEEE VLAN\n"); + /* VET hardcoded to standard value and VFTA removed in ICH8 LAN */ + if (hw->mac_type != e1000_ich8lan) { + if (hw->mac_type < e1000_82545_rev_3) + E1000_WRITE_REG(hw, VET, 0); + e1000_clear_vfta(hw); + } + + /* For 82542 (rev 2.0), disable MWI and put the receiver into reset */ + if (hw->mac_type == e1000_82542_rev2_0) { + DEBUGOUT("Disabling MWI on 82542 rev 2.0\n"); + e1000_pci_clear_mwi(hw); + E1000_WRITE_REG(hw, RCTL, E1000_RCTL_RST); + E1000_WRITE_FLUSH(hw); + msleep(5); + } + + /* Setup the receive address. This involves initializing all of the Receive + * Address Registers (RARs 0 - 15). + */ + e1000_init_rx_addrs(hw); + + /* For 82542 (rev 2.0), take the receiver out of reset and enable MWI */ + if (hw->mac_type == e1000_82542_rev2_0) { + E1000_WRITE_REG(hw, RCTL, 0); + E1000_WRITE_FLUSH(hw); + msleep(1); + if (hw->pci_cmd_word & PCI_COMMAND_INVALIDATE) + e1000_pci_set_mwi(hw); + } + + /* Zero out the Multicast HASH table */ + DEBUGOUT("Zeroing the MTA\n"); + mta_size = E1000_MC_TBL_SIZE; + if (hw->mac_type == e1000_ich8lan) + mta_size = E1000_MC_TBL_SIZE_ICH8LAN; + for (i = 0; i < mta_size; i++) { + E1000_WRITE_REG_ARRAY(hw, MTA, i, 0); + /* use write flush to prevent Memory Write Block (MWB) from + * occuring when accessing our register space */ + E1000_WRITE_FLUSH(hw); + } + + /* Set the PCI priority bit correctly in the CTRL register. This + * determines if the adapter gives priority to receives, or if it + * gives equal priority to transmits and receives. Valid only on + * 82542 and 82543 silicon. + */ + if (hw->dma_fairness && hw->mac_type <= e1000_82543) { + ctrl = E1000_READ_REG(hw, CTRL); + E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PRIOR); + } + + switch (hw->mac_type) { + case e1000_82545_rev_3: + case e1000_82546_rev_3: + break; + default: + /* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */ + if (hw->bus_type == e1000_bus_type_pcix && e1000_pcix_get_mmrbc(hw) > 2048) + e1000_pcix_set_mmrbc(hw, 2048); + break; + } + + /* More time needed for PHY to initialize */ + if (hw->mac_type == e1000_ich8lan) + msleep(15); + + /* Call a subroutine to configure the link and setup flow control. */ + ret_val = e1000_setup_link(hw); + + /* Set the transmit descriptor write-back policy */ + if (hw->mac_type > e1000_82544) { + ctrl = E1000_READ_REG(hw, TXDCTL); + ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB; + E1000_WRITE_REG(hw, TXDCTL, ctrl); + } + + if (hw->mac_type == e1000_82573) { + e1000_enable_tx_pkt_filtering(hw); + } + + switch (hw->mac_type) { + default: + break; + case e1000_80003es2lan: + /* Enable retransmit on late collisions */ + reg_data = E1000_READ_REG(hw, TCTL); + reg_data |= E1000_TCTL_RTLC; + E1000_WRITE_REG(hw, TCTL, reg_data); + + /* Configure Gigabit Carry Extend Padding */ + reg_data = E1000_READ_REG(hw, TCTL_EXT); + reg_data &= ~E1000_TCTL_EXT_GCEX_MASK; + reg_data |= DEFAULT_80003ES2LAN_TCTL_EXT_GCEX; + E1000_WRITE_REG(hw, TCTL_EXT, reg_data); + + /* Configure Transmit Inter-Packet Gap */ + reg_data = E1000_READ_REG(hw, TIPG); + reg_data &= ~E1000_TIPG_IPGT_MASK; + reg_data |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000; + E1000_WRITE_REG(hw, TIPG, reg_data); + + reg_data = E1000_READ_REG_ARRAY(hw, FFLT, 0x0001); + reg_data &= ~0x00100000; + E1000_WRITE_REG_ARRAY(hw, FFLT, 0x0001, reg_data); + /* Fall through */ + case e1000_82571: + case e1000_82572: + case e1000_ich8lan: + ctrl = E1000_READ_REG(hw, TXDCTL1); + ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB; + E1000_WRITE_REG(hw, TXDCTL1, ctrl); + break; + } + + + if (hw->mac_type == e1000_82573) { + uint32_t gcr = E1000_READ_REG(hw, GCR); + gcr |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX; + E1000_WRITE_REG(hw, GCR, gcr); + } + + /* Clear all of the statistics registers (clear on read). It is + * important that we do this after we have tried to establish link + * because the symbol error count will increment wildly if there + * is no link. + */ + e1000_clear_hw_cntrs(hw); + + /* ICH8 No-snoop bits are opposite polarity. + * Set to snoop by default after reset. */ + if (hw->mac_type == e1000_ich8lan) + e1000_set_pci_ex_no_snoop(hw, PCI_EX_82566_SNOOP_ALL); + + if (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER || + hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) { + ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); + /* Relaxed ordering must be disabled to avoid a parity + * error crash in a PCI slot. */ + ctrl_ext |= E1000_CTRL_EXT_RO_DIS; + E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); + } + + return ret_val; +} + +/****************************************************************************** + * Adjust SERDES output amplitude based on EEPROM setting. + * + * hw - Struct containing variables accessed by shared code. + *****************************************************************************/ +static int32_t +e1000_adjust_serdes_amplitude(struct e1000_hw *hw) +{ + uint16_t eeprom_data; + int32_t ret_val; + + DEBUGFUNC("e1000_adjust_serdes_amplitude"); + + if (hw->media_type != e1000_media_type_internal_serdes) + return E1000_SUCCESS; + + switch (hw->mac_type) { + case e1000_82545_rev_3: + case e1000_82546_rev_3: + break; + default: + return E1000_SUCCESS; + } + + ret_val = e1000_read_eeprom(hw, EEPROM_SERDES_AMPLITUDE, 1, &eeprom_data); + if (ret_val) { + return ret_val; + } + + if (eeprom_data != EEPROM_RESERVED_WORD) { + /* Adjust SERDES output amplitude only. */ + eeprom_data &= EEPROM_SERDES_AMPLITUDE_MASK; + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_EXT_CTRL, eeprom_data); + if (ret_val) + return ret_val; + } + + return E1000_SUCCESS; +} + +/****************************************************************************** + * Configures flow control and link settings. + * + * hw - Struct containing variables accessed by shared code + * + * Determines which flow control settings to use. Calls the apropriate media- + * specific link configuration function. Configures the flow control settings. + * Assuming the adapter has a valid link partner, a valid link should be + * established. Assumes the hardware has previously been reset and the + * transmitter and receiver are not enabled. + *****************************************************************************/ +int32_t +e1000_setup_link(struct e1000_hw *hw) +{ + uint32_t ctrl_ext; + int32_t ret_val; + uint16_t eeprom_data; + + DEBUGFUNC("e1000_setup_link"); + + /* In the case of the phy reset being blocked, we already have a link. + * We do not have to set it up again. */ + if (e1000_check_phy_reset_block(hw)) + return E1000_SUCCESS; + + /* Read and store word 0x0F of the EEPROM. This word contains bits + * that determine the hardware's default PAUSE (flow control) mode, + * a bit that determines whether the HW defaults to enabling or + * disabling auto-negotiation, and the direction of the + * SW defined pins. If there is no SW over-ride of the flow + * control setting, then the variable hw->fc will + * be initialized based on a value in the EEPROM. + */ + if (hw->fc == E1000_FC_DEFAULT) { + switch (hw->mac_type) { + case e1000_ich8lan: + case e1000_82573: + hw->fc = E1000_FC_FULL; + break; + default: + ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, + 1, &eeprom_data); + if (ret_val) { + DEBUGOUT("EEPROM Read Error\n"); + return -E1000_ERR_EEPROM; + } + if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0) + hw->fc = E1000_FC_NONE; + else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == + EEPROM_WORD0F_ASM_DIR) + hw->fc = E1000_FC_TX_PAUSE; + else + hw->fc = E1000_FC_FULL; + break; + } + } + + /* We want to save off the original Flow Control configuration just + * in case we get disconnected and then reconnected into a different + * hub or switch with different Flow Control capabilities. + */ + if (hw->mac_type == e1000_82542_rev2_0) + hw->fc &= (~E1000_FC_TX_PAUSE); + + if ((hw->mac_type < e1000_82543) && (hw->report_tx_early == 1)) + hw->fc &= (~E1000_FC_RX_PAUSE); + + hw->original_fc = hw->fc; + + DEBUGOUT1("After fix-ups FlowControl is now = %x\n", hw->fc); + + /* Take the 4 bits from EEPROM word 0x0F that determine the initial + * polarity value for the SW controlled pins, and setup the + * Extended Device Control reg with that info. + * This is needed because one of the SW controlled pins is used for + * signal detection. So this should be done before e1000_setup_pcs_link() + * or e1000_phy_setup() is called. + */ + if (hw->mac_type == e1000_82543) { + ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, + 1, &eeprom_data); + if (ret_val) { + DEBUGOUT("EEPROM Read Error\n"); + return -E1000_ERR_EEPROM; + } + ctrl_ext = ((eeprom_data & EEPROM_WORD0F_SWPDIO_EXT) << + SWDPIO__EXT_SHIFT); + E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); + } + + /* Call the necessary subroutine to configure the link. */ + ret_val = (hw->media_type == e1000_media_type_copper) ? + e1000_setup_copper_link(hw) : + e1000_setup_fiber_serdes_link(hw); + + /* Initialize the flow control address, type, and PAUSE timer + * registers to their default values. This is done even if flow + * control is disabled, because it does not hurt anything to + * initialize these registers. + */ + DEBUGOUT("Initializing the Flow Control address, type and timer regs\n"); + + /* FCAL/H and FCT are hardcoded to standard values in e1000_ich8lan. */ + if (hw->mac_type != e1000_ich8lan) { + E1000_WRITE_REG(hw, FCT, FLOW_CONTROL_TYPE); + E1000_WRITE_REG(hw, FCAH, FLOW_CONTROL_ADDRESS_HIGH); + E1000_WRITE_REG(hw, FCAL, FLOW_CONTROL_ADDRESS_LOW); + } + + E1000_WRITE_REG(hw, FCTTV, hw->fc_pause_time); + + /* Set the flow control receive threshold registers. Normally, + * these registers will be set to a default threshold that may be + * adjusted later by the driver's runtime code. However, if the + * ability to transmit pause frames in not enabled, then these + * registers will be set to 0. + */ + if (!(hw->fc & E1000_FC_TX_PAUSE)) { + E1000_WRITE_REG(hw, FCRTL, 0); + E1000_WRITE_REG(hw, FCRTH, 0); + } else { + /* We need to set up the Receive Threshold high and low water marks + * as well as (optionally) enabling the transmission of XON frames. + */ + if (hw->fc_send_xon) { + E1000_WRITE_REG(hw, FCRTL, (hw->fc_low_water | E1000_FCRTL_XONE)); + E1000_WRITE_REG(hw, FCRTH, hw->fc_high_water); + } else { + E1000_WRITE_REG(hw, FCRTL, hw->fc_low_water); + E1000_WRITE_REG(hw, FCRTH, hw->fc_high_water); + } + } + return ret_val; +} + +/****************************************************************************** + * Sets up link for a fiber based or serdes based adapter + * + * hw - Struct containing variables accessed by shared code + * + * Manipulates Physical Coding Sublayer functions in order to configure + * link. Assumes the hardware has been previously reset and the transmitter + * and receiver are not enabled. + *****************************************************************************/ +static int32_t +e1000_setup_fiber_serdes_link(struct e1000_hw *hw) +{ + uint32_t ctrl; + uint32_t status; + uint32_t txcw = 0; + uint32_t i; + uint32_t signal = 0; + int32_t ret_val; + + DEBUGFUNC("e1000_setup_fiber_serdes_link"); + + /* On 82571 and 82572 Fiber connections, SerDes loopback mode persists + * until explicitly turned off or a power cycle is performed. A read to + * the register does not indicate its status. Therefore, we ensure + * loopback mode is disabled during initialization. + */ + if (hw->mac_type == e1000_82571 || hw->mac_type == e1000_82572) + E1000_WRITE_REG(hw, SCTL, E1000_DISABLE_SERDES_LOOPBACK); + + /* On adapters with a MAC newer than 82544, SWDP 1 will be + * set when the optics detect a signal. On older adapters, it will be + * cleared when there is a signal. This applies to fiber media only. + * If we're on serdes media, adjust the output amplitude to value + * set in the EEPROM. + */ + ctrl = E1000_READ_REG(hw, CTRL); + if (hw->media_type == e1000_media_type_fiber) + signal = (hw->mac_type > e1000_82544) ? E1000_CTRL_SWDPIN1 : 0; + + ret_val = e1000_adjust_serdes_amplitude(hw); + if (ret_val) + return ret_val; + + /* Take the link out of reset */ + ctrl &= ~(E1000_CTRL_LRST); + + /* Adjust VCO speed to improve BER performance */ + ret_val = e1000_set_vco_speed(hw); + if (ret_val) + return ret_val; + + e1000_config_collision_dist(hw); + + /* Check for a software override of the flow control settings, and setup + * the device accordingly. If auto-negotiation is enabled, then software + * will have to set the "PAUSE" bits to the correct value in the Tranmsit + * Config Word Register (TXCW) and re-start auto-negotiation. However, if + * auto-negotiation is disabled, then software will have to manually + * configure the two flow control enable bits in the CTRL register. + * + * The possible values of the "fc" parameter are: + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause frames, but + * not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames but we do + * not support receiving pause frames). + * 3: Both Rx and TX flow control (symmetric) are enabled. + */ + switch (hw->fc) { + case E1000_FC_NONE: + /* Flow control is completely disabled by a software over-ride. */ + txcw = (E1000_TXCW_ANE | E1000_TXCW_FD); + break; + case E1000_FC_RX_PAUSE: + /* RX Flow control is enabled and TX Flow control is disabled by a + * software over-ride. Since there really isn't a way to advertise + * that we are capable of RX Pause ONLY, we will advertise that we + * support both symmetric and asymmetric RX PAUSE. Later, we will + * disable the adapter's ability to send PAUSE frames. + */ + txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK); + break; + case E1000_FC_TX_PAUSE: + /* TX Flow control is enabled, and RX Flow control is disabled, by a + * software over-ride. + */ + txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR); + break; + case E1000_FC_FULL: + /* Flow control (both RX and TX) is enabled by a software over-ride. */ + txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK); + break; + default: + DEBUGOUT("Flow control param set incorrectly\n"); + return -E1000_ERR_CONFIG; + break; + } + + /* Since auto-negotiation is enabled, take the link out of reset (the link + * will be in reset, because we previously reset the chip). This will + * restart auto-negotiation. If auto-neogtiation is successful then the + * link-up status bit will be set and the flow control enable bits (RFCE + * and TFCE) will be set according to their negotiated value. + */ + DEBUGOUT("Auto-negotiation enabled\n"); + + E1000_WRITE_REG(hw, TXCW, txcw); + E1000_WRITE_REG(hw, CTRL, ctrl); + E1000_WRITE_FLUSH(hw); + + hw->txcw = txcw; + msleep(1); + + /* If we have a signal (the cable is plugged in) then poll for a "Link-Up" + * indication in the Device Status Register. Time-out if a link isn't + * seen in 500 milliseconds seconds (Auto-negotiation should complete in + * less than 500 milliseconds even if the other end is doing it in SW). + * For internal serdes, we just assume a signal is present, then poll. + */ + if (hw->media_type == e1000_media_type_internal_serdes || + (E1000_READ_REG(hw, CTRL) & E1000_CTRL_SWDPIN1) == signal) { + DEBUGOUT("Looking for Link\n"); + for (i = 0; i < (LINK_UP_TIMEOUT / 10); i++) { + msleep(10); + status = E1000_READ_REG(hw, STATUS); + if (status & E1000_STATUS_LU) break; + } + if (i == (LINK_UP_TIMEOUT / 10)) { + DEBUGOUT("Never got a valid link from auto-neg!!!\n"); + hw->autoneg_failed = 1; + /* AutoNeg failed to achieve a link, so we'll call + * e1000_check_for_link. This routine will force the link up if + * we detect a signal. This will allow us to communicate with + * non-autonegotiating link partners. + */ + ret_val = e1000_check_for_link(hw); + if (ret_val) { + DEBUGOUT("Error while checking for link\n"); + return ret_val; + } + hw->autoneg_failed = 0; + } else { + hw->autoneg_failed = 0; + DEBUGOUT("Valid Link Found\n"); + } + } else { + DEBUGOUT("No Signal Detected\n"); + } + return E1000_SUCCESS; +} + +/****************************************************************************** +* Make sure we have a valid PHY and change PHY mode before link setup. +* +* hw - Struct containing variables accessed by shared code +******************************************************************************/ +static int32_t +e1000_copper_link_preconfig(struct e1000_hw *hw) +{ + uint32_t ctrl; + int32_t ret_val; + uint16_t phy_data; + + DEBUGFUNC("e1000_copper_link_preconfig"); + + ctrl = E1000_READ_REG(hw, CTRL); + /* With 82543, we need to force speed and duplex on the MAC equal to what + * the PHY speed and duplex configuration is. In addition, we need to + * perform a hardware reset on the PHY to take it out of reset. + */ + if (hw->mac_type > e1000_82543) { + ctrl |= E1000_CTRL_SLU; + ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); + E1000_WRITE_REG(hw, CTRL, ctrl); + } else { + ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX | E1000_CTRL_SLU); + E1000_WRITE_REG(hw, CTRL, ctrl); + ret_val = e1000_phy_hw_reset(hw); + if (ret_val) + return ret_val; + } + + /* Make sure we have a valid PHY */ + ret_val = e1000_detect_gig_phy(hw); + if (ret_val) { + DEBUGOUT("Error, did not detect valid phy.\n"); + return ret_val; + } + DEBUGOUT1("Phy ID = %x \n", hw->phy_id); + + /* Set PHY to class A mode (if necessary) */ + ret_val = e1000_set_phy_mode(hw); + if (ret_val) + return ret_val; + + if ((hw->mac_type == e1000_82545_rev_3) || + (hw->mac_type == e1000_82546_rev_3)) { + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + phy_data |= 0x00000008; + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); + } + + if (hw->mac_type <= e1000_82543 || + hw->mac_type == e1000_82541 || hw->mac_type == e1000_82547 || + hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2) + hw->phy_reset_disable = FALSE; + + return E1000_SUCCESS; +} + + +/******************************************************************** +* Copper link setup for e1000_phy_igp series. +* +* hw - Struct containing variables accessed by shared code +*********************************************************************/ +static int32_t +e1000_copper_link_igp_setup(struct e1000_hw *hw) +{ + uint32_t led_ctrl; + int32_t ret_val; + uint16_t phy_data; + + DEBUGFUNC("e1000_copper_link_igp_setup"); + + if (hw->phy_reset_disable) + return E1000_SUCCESS; + + ret_val = e1000_phy_reset(hw); + if (ret_val) { + DEBUGOUT("Error Resetting the PHY\n"); + return ret_val; + } + + /* Wait 15ms for MAC to configure PHY from eeprom settings */ + msleep(15); + if (hw->mac_type != e1000_ich8lan) { + /* Configure activity LED after PHY reset */ + led_ctrl = E1000_READ_REG(hw, LEDCTL); + led_ctrl &= IGP_ACTIVITY_LED_MASK; + led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); + E1000_WRITE_REG(hw, LEDCTL, led_ctrl); + } + + /* The NVM settings will configure LPLU in D3 for IGP2 and IGP3 PHYs */ + if (hw->phy_type == e1000_phy_igp) { + /* disable lplu d3 during driver init */ + ret_val = e1000_set_d3_lplu_state(hw, FALSE); + if (ret_val) { + DEBUGOUT("Error Disabling LPLU D3\n"); + return ret_val; + } + } + + /* disable lplu d0 during driver init */ + ret_val = e1000_set_d0_lplu_state(hw, FALSE); + if (ret_val) { + DEBUGOUT("Error Disabling LPLU D0\n"); + return ret_val; + } + /* Configure mdi-mdix settings */ + ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data); + if (ret_val) + return ret_val; + + if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) { + hw->dsp_config_state = e1000_dsp_config_disabled; + /* Force MDI for earlier revs of the IGP PHY */ + phy_data &= ~(IGP01E1000_PSCR_AUTO_MDIX | IGP01E1000_PSCR_FORCE_MDI_MDIX); + hw->mdix = 1; + + } else { + hw->dsp_config_state = e1000_dsp_config_enabled; + phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX; + + switch (hw->mdix) { + case 1: + phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX; + break; + case 2: + phy_data |= IGP01E1000_PSCR_FORCE_MDI_MDIX; + break; + case 0: + default: + phy_data |= IGP01E1000_PSCR_AUTO_MDIX; + break; + } + } + ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data); + if (ret_val) + return ret_val; + + /* set auto-master slave resolution settings */ + if (hw->autoneg) { + e1000_ms_type phy_ms_setting = hw->master_slave; + + if (hw->ffe_config_state == e1000_ffe_config_active) + hw->ffe_config_state = e1000_ffe_config_enabled; + + if (hw->dsp_config_state == e1000_dsp_config_activated) + hw->dsp_config_state = e1000_dsp_config_enabled; + + /* when autonegotiation advertisment is only 1000Mbps then we + * should disable SmartSpeed and enable Auto MasterSlave + * resolution as hardware default. */ + if (hw->autoneg_advertised == ADVERTISE_1000_FULL) { + /* Disable SmartSpeed */ + ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + &phy_data); + if (ret_val) + return ret_val; + phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + phy_data); + if (ret_val) + return ret_val; + /* Set auto Master/Slave resolution process */ + ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data); + if (ret_val) + return ret_val; + phy_data &= ~CR_1000T_MS_ENABLE; + ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data); + if (ret_val) + return ret_val; + } + + ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data); + if (ret_val) + return ret_val; + + /* load defaults for future use */ + hw->original_master_slave = (phy_data & CR_1000T_MS_ENABLE) ? + ((phy_data & CR_1000T_MS_VALUE) ? + e1000_ms_force_master : + e1000_ms_force_slave) : + e1000_ms_auto; + + switch (phy_ms_setting) { + case e1000_ms_force_master: + phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE); + break; + case e1000_ms_force_slave: + phy_data |= CR_1000T_MS_ENABLE; + phy_data &= ~(CR_1000T_MS_VALUE); + break; + case e1000_ms_auto: + phy_data &= ~CR_1000T_MS_ENABLE; + default: + break; + } + ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data); + if (ret_val) + return ret_val; + } + + return E1000_SUCCESS; +} + +/******************************************************************** +* Copper link setup for e1000_phy_gg82563 series. +* +* hw - Struct containing variables accessed by shared code +*********************************************************************/ +static int32_t +e1000_copper_link_ggp_setup(struct e1000_hw *hw) +{ + int32_t ret_val; + uint16_t phy_data; + uint32_t reg_data; + + DEBUGFUNC("e1000_copper_link_ggp_setup"); + + if (!hw->phy_reset_disable) { + + /* Enable CRS on TX for half-duplex operation. */ + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, + &phy_data); + if (ret_val) + return ret_val; + + phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX; + /* Use 25MHz for both link down and 1000BASE-T for Tx clock */ + phy_data |= GG82563_MSCR_TX_CLK_1000MBPS_25MHZ; + + ret_val = e1000_write_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, + phy_data); + if (ret_val) + return ret_val; + + /* Options: + * MDI/MDI-X = 0 (default) + * 0 - Auto for all speeds + * 1 - MDI mode + * 2 - MDI-X mode + * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) + */ + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + return ret_val; + + phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK; + + switch (hw->mdix) { + case 1: + phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDI; + break; + case 2: + phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDIX; + break; + case 0: + default: + phy_data |= GG82563_PSCR_CROSSOVER_MODE_AUTO; + break; + } + + /* Options: + * disable_polarity_correction = 0 (default) + * Automatic Correction for Reversed Cable Polarity + * 0 - Disabled + * 1 - Enabled + */ + phy_data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE; + if (hw->disable_polarity_correction == 1) + phy_data |= GG82563_PSCR_POLARITY_REVERSAL_DISABLE; + ret_val = e1000_write_phy_reg(hw, GG82563_PHY_SPEC_CTRL, phy_data); + + if (ret_val) + return ret_val; + + /* SW Reset the PHY so all changes take effect */ + ret_val = e1000_phy_reset(hw); + if (ret_val) { + DEBUGOUT("Error Resetting the PHY\n"); + return ret_val; + } + } /* phy_reset_disable */ + + if (hw->mac_type == e1000_80003es2lan) { + /* Bypass RX and TX FIFO's */ + ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_FIFO_CTRL, + E1000_KUMCTRLSTA_FIFO_CTRL_RX_BYPASS | + E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS); + if (ret_val) + return ret_val; + + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_SPEC_CTRL_2, &phy_data); + if (ret_val) + return ret_val; + + phy_data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG; + ret_val = e1000_write_phy_reg(hw, GG82563_PHY_SPEC_CTRL_2, phy_data); + + if (ret_val) + return ret_val; + + reg_data = E1000_READ_REG(hw, CTRL_EXT); + reg_data &= ~(E1000_CTRL_EXT_LINK_MODE_MASK); + E1000_WRITE_REG(hw, CTRL_EXT, reg_data); + + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_PWR_MGMT_CTRL, + &phy_data); + if (ret_val) + return ret_val; + + /* Do not init these registers when the HW is in IAMT mode, since the + * firmware will have already initialized them. We only initialize + * them if the HW is not in IAMT mode. + */ + if (e1000_check_mng_mode(hw) == FALSE) { + /* Enable Electrical Idle on the PHY */ + phy_data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE; + ret_val = e1000_write_phy_reg(hw, GG82563_PHY_PWR_MGMT_CTRL, + phy_data); + if (ret_val) + return ret_val; + + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, + &phy_data); + if (ret_val) + return ret_val; + + phy_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; + ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, + phy_data); + + if (ret_val) + return ret_val; + } + + /* Workaround: Disable padding in Kumeran interface in the MAC + * and in the PHY to avoid CRC errors. + */ + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_INBAND_CTRL, + &phy_data); + if (ret_val) + return ret_val; + phy_data |= GG82563_ICR_DIS_PADDING; + ret_val = e1000_write_phy_reg(hw, GG82563_PHY_INBAND_CTRL, + phy_data); + if (ret_val) + return ret_val; + } + + return E1000_SUCCESS; +} + +/******************************************************************** +* Copper link setup for e1000_phy_m88 series. +* +* hw - Struct containing variables accessed by shared code +*********************************************************************/ +static int32_t +e1000_copper_link_mgp_setup(struct e1000_hw *hw) +{ + int32_t ret_val; + uint16_t phy_data; + + DEBUGFUNC("e1000_copper_link_mgp_setup"); + + if (hw->phy_reset_disable) + return E1000_SUCCESS; + + /* Enable CRS on TX. This must be set for half-duplex operation. */ + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + return ret_val; + + phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX; + + /* Options: + * MDI/MDI-X = 0 (default) + * 0 - Auto for all speeds + * 1 - MDI mode + * 2 - MDI-X mode + * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) + */ + phy_data &= ~M88E1000_PSCR_AUTO_X_MODE; + + switch (hw->mdix) { + case 1: + phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE; + break; + case 2: + phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE; + break; + case 3: + phy_data |= M88E1000_PSCR_AUTO_X_1000T; + break; + case 0: + default: + phy_data |= M88E1000_PSCR_AUTO_X_MODE; + break; + } + + /* Options: + * disable_polarity_correction = 0 (default) + * Automatic Correction for Reversed Cable Polarity + * 0 - Disabled + * 1 - Enabled + */ + phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL; + if (hw->disable_polarity_correction == 1) + phy_data |= M88E1000_PSCR_POLARITY_REVERSAL; + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); + if (ret_val) + return ret_val; + + if (hw->phy_revision < M88E1011_I_REV_4) { + /* Force TX_CLK in the Extended PHY Specific Control Register + * to 25MHz clock. + */ + ret_val = e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + return ret_val; + + phy_data |= M88E1000_EPSCR_TX_CLK_25; + + if ((hw->phy_revision == E1000_REVISION_2) && + (hw->phy_id == M88E1111_I_PHY_ID)) { + /* Vidalia Phy, set the downshift counter to 5x */ + phy_data &= ~(M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK); + phy_data |= M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X; + ret_val = e1000_write_phy_reg(hw, + M88E1000_EXT_PHY_SPEC_CTRL, phy_data); + if (ret_val) + return ret_val; + } else { + /* Configure Master and Slave downshift values */ + phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK | + M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK); + phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X | + M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X); + ret_val = e1000_write_phy_reg(hw, + M88E1000_EXT_PHY_SPEC_CTRL, phy_data); + if (ret_val) + return ret_val; + } + } + + /* SW Reset the PHY so all changes take effect */ + ret_val = e1000_phy_reset(hw); + if (ret_val) { + DEBUGOUT("Error Resetting the PHY\n"); + return ret_val; + } + + return E1000_SUCCESS; +} + +/******************************************************************** +* Setup auto-negotiation and flow control advertisements, +* and then perform auto-negotiation. +* +* hw - Struct containing variables accessed by shared code +*********************************************************************/ +static int32_t +e1000_copper_link_autoneg(struct e1000_hw *hw) +{ + int32_t ret_val; + uint16_t phy_data; + + DEBUGFUNC("e1000_copper_link_autoneg"); + + /* Perform some bounds checking on the hw->autoneg_advertised + * parameter. If this variable is zero, then set it to the default. + */ + hw->autoneg_advertised &= AUTONEG_ADVERTISE_SPEED_DEFAULT; + + /* If autoneg_advertised is zero, we assume it was not defaulted + * by the calling code so we set to advertise full capability. + */ + if (hw->autoneg_advertised == 0) + hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT; + + /* IFE phy only supports 10/100 */ + if (hw->phy_type == e1000_phy_ife) + hw->autoneg_advertised &= AUTONEG_ADVERTISE_10_100_ALL; + + DEBUGOUT("Reconfiguring auto-neg advertisement params\n"); + ret_val = e1000_phy_setup_autoneg(hw); + if (ret_val) { + DEBUGOUT("Error Setting up Auto-Negotiation\n"); + return ret_val; + } + DEBUGOUT("Restarting Auto-Neg\n"); + + /* Restart auto-negotiation by setting the Auto Neg Enable bit and + * the Auto Neg Restart bit in the PHY control register. + */ + ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data); + if (ret_val) + return ret_val; + + phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG); + ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data); + if (ret_val) + return ret_val; + + /* Does the user want to wait for Auto-Neg to complete here, or + * check at a later time (for example, callback routine). + */ + if (hw->wait_autoneg_complete) { + ret_val = e1000_wait_autoneg(hw); + if (ret_val) { + DEBUGOUT("Error while waiting for autoneg to complete\n"); + return ret_val; + } + } + + hw->get_link_status = TRUE; + + return E1000_SUCCESS; +} + +/****************************************************************************** +* Config the MAC and the PHY after link is up. +* 1) Set up the MAC to the current PHY speed/duplex +* if we are on 82543. If we +* are on newer silicon, we only need to configure +* collision distance in the Transmit Control Register. +* 2) Set up flow control on the MAC to that established with +* the link partner. +* 3) Config DSP to improve Gigabit link quality for some PHY revisions. +* +* hw - Struct containing variables accessed by shared code +******************************************************************************/ +static int32_t +e1000_copper_link_postconfig(struct e1000_hw *hw) +{ + int32_t ret_val; + DEBUGFUNC("e1000_copper_link_postconfig"); + + if (hw->mac_type >= e1000_82544) { + e1000_config_collision_dist(hw); + } else { + ret_val = e1000_config_mac_to_phy(hw); + if (ret_val) { + DEBUGOUT("Error configuring MAC to PHY settings\n"); + return ret_val; + } + } + ret_val = e1000_config_fc_after_link_up(hw); + if (ret_val) { + DEBUGOUT("Error Configuring Flow Control\n"); + return ret_val; + } + + /* Config DSP to improve Giga link quality */ + if (hw->phy_type == e1000_phy_igp) { + ret_val = e1000_config_dsp_after_link_change(hw, TRUE); + if (ret_val) { + DEBUGOUT("Error Configuring DSP after link up\n"); + return ret_val; + } + } + + return E1000_SUCCESS; +} + +/****************************************************************************** +* Detects which PHY is present and setup the speed and duplex +* +* hw - Struct containing variables accessed by shared code +******************************************************************************/ +static int32_t +e1000_setup_copper_link(struct e1000_hw *hw) +{ + int32_t ret_val; + uint16_t i; + uint16_t phy_data; + uint16_t reg_data; + + DEBUGFUNC("e1000_setup_copper_link"); + + switch (hw->mac_type) { + case e1000_80003es2lan: + case e1000_ich8lan: + /* Set the mac to wait the maximum time between each + * iteration and increase the max iterations when + * polling the phy; this fixes erroneous timeouts at 10Mbps. */ + ret_val = e1000_write_kmrn_reg(hw, GG82563_REG(0x34, 4), 0xFFFF); + if (ret_val) + return ret_val; + ret_val = e1000_read_kmrn_reg(hw, GG82563_REG(0x34, 9), ®_data); + if (ret_val) + return ret_val; + reg_data |= 0x3F; + ret_val = e1000_write_kmrn_reg(hw, GG82563_REG(0x34, 9), reg_data); + if (ret_val) + return ret_val; + default: + break; + } + + /* Check if it is a valid PHY and set PHY mode if necessary. */ + ret_val = e1000_copper_link_preconfig(hw); + if (ret_val) + return ret_val; + + switch (hw->mac_type) { + case e1000_80003es2lan: + /* Kumeran registers are written-only */ + reg_data = E1000_KUMCTRLSTA_INB_CTRL_LINK_STATUS_TX_TIMEOUT_DEFAULT; + reg_data |= E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING; + ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_INB_CTRL, + reg_data); + if (ret_val) + return ret_val; + break; + default: + break; + } + + if (hw->phy_type == e1000_phy_igp || + hw->phy_type == e1000_phy_igp_3 || + hw->phy_type == e1000_phy_igp_2) { + ret_val = e1000_copper_link_igp_setup(hw); + if (ret_val) + return ret_val; + } else if (hw->phy_type == e1000_phy_m88) { + ret_val = e1000_copper_link_mgp_setup(hw); + if (ret_val) + return ret_val; + } else if (hw->phy_type == e1000_phy_gg82563) { + ret_val = e1000_copper_link_ggp_setup(hw); + if (ret_val) + return ret_val; + } + + if (hw->autoneg) { + /* Setup autoneg and flow control advertisement + * and perform autonegotiation */ + ret_val = e1000_copper_link_autoneg(hw); + if (ret_val) + return ret_val; + } else { + /* PHY will be set to 10H, 10F, 100H,or 100F + * depending on value from forced_speed_duplex. */ + DEBUGOUT("Forcing speed and duplex\n"); + ret_val = e1000_phy_force_speed_duplex(hw); + if (ret_val) { + DEBUGOUT("Error Forcing Speed and Duplex\n"); + return ret_val; + } + } + + /* Check link status. Wait up to 100 microseconds for link to become + * valid. + */ + for (i = 0; i < 10; i++) { + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); + if (ret_val) + return ret_val; + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); + if (ret_val) + return ret_val; + + if (phy_data & MII_SR_LINK_STATUS) { + /* Config the MAC and PHY after link is up */ + ret_val = e1000_copper_link_postconfig(hw); + if (ret_val) + return ret_val; + + DEBUGOUT("Valid link established!!!\n"); + return E1000_SUCCESS; + } + udelay(10); + } + + DEBUGOUT("Unable to establish link!!!\n"); + return E1000_SUCCESS; +} + +/****************************************************************************** +* Configure the MAC-to-PHY interface for 10/100Mbps +* +* hw - Struct containing variables accessed by shared code +******************************************************************************/ +static int32_t +e1000_configure_kmrn_for_10_100(struct e1000_hw *hw, uint16_t duplex) +{ + int32_t ret_val = E1000_SUCCESS; + uint32_t tipg; + uint16_t reg_data; + + DEBUGFUNC("e1000_configure_kmrn_for_10_100"); + + reg_data = E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT; + ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_HD_CTRL, + reg_data); + if (ret_val) + return ret_val; + + /* Configure Transmit Inter-Packet Gap */ + tipg = E1000_READ_REG(hw, TIPG); + tipg &= ~E1000_TIPG_IPGT_MASK; + tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_10_100; + E1000_WRITE_REG(hw, TIPG, tipg); + + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data); + + if (ret_val) + return ret_val; + + if (duplex == HALF_DUPLEX) + reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER; + else + reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; + + ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); + + return ret_val; +} + +static int32_t +e1000_configure_kmrn_for_1000(struct e1000_hw *hw) +{ + int32_t ret_val = E1000_SUCCESS; + uint16_t reg_data; + uint32_t tipg; + + DEBUGFUNC("e1000_configure_kmrn_for_1000"); + + reg_data = E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT; + ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_HD_CTRL, + reg_data); + if (ret_val) + return ret_val; + + /* Configure Transmit Inter-Packet Gap */ + tipg = E1000_READ_REG(hw, TIPG); + tipg &= ~E1000_TIPG_IPGT_MASK; + tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000; + E1000_WRITE_REG(hw, TIPG, tipg); + + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data); + + if (ret_val) + return ret_val; + + reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; + ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); + + return ret_val; +} + +/****************************************************************************** +* Configures PHY autoneg and flow control advertisement settings +* +* hw - Struct containing variables accessed by shared code +******************************************************************************/ +int32_t +e1000_phy_setup_autoneg(struct e1000_hw *hw) +{ + int32_t ret_val; + uint16_t mii_autoneg_adv_reg; + uint16_t mii_1000t_ctrl_reg; + + DEBUGFUNC("e1000_phy_setup_autoneg"); + + /* Read the MII Auto-Neg Advertisement Register (Address 4). */ + ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg); + if (ret_val) + return ret_val; + + if (hw->phy_type != e1000_phy_ife) { + /* Read the MII 1000Base-T Control Register (Address 9). */ + ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg); + if (ret_val) + return ret_val; + } else + mii_1000t_ctrl_reg=0; + + /* Need to parse both autoneg_advertised and fc and set up + * the appropriate PHY registers. First we will parse for + * autoneg_advertised software override. Since we can advertise + * a plethora of combinations, we need to check each bit + * individually. + */ + + /* First we clear all the 10/100 mb speed bits in the Auto-Neg + * Advertisement Register (Address 4) and the 1000 mb speed bits in + * the 1000Base-T Control Register (Address 9). + */ + mii_autoneg_adv_reg &= ~REG4_SPEED_MASK; + mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK; + + DEBUGOUT1("autoneg_advertised %x\n", hw->autoneg_advertised); + + /* Do we want to advertise 10 Mb Half Duplex? */ + if (hw->autoneg_advertised & ADVERTISE_10_HALF) { + DEBUGOUT("Advertise 10mb Half duplex\n"); + mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS; + } + + /* Do we want to advertise 10 Mb Full Duplex? */ + if (hw->autoneg_advertised & ADVERTISE_10_FULL) { + DEBUGOUT("Advertise 10mb Full duplex\n"); + mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS; + } + + /* Do we want to advertise 100 Mb Half Duplex? */ + if (hw->autoneg_advertised & ADVERTISE_100_HALF) { + DEBUGOUT("Advertise 100mb Half duplex\n"); + mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS; + } + + /* Do we want to advertise 100 Mb Full Duplex? */ + if (hw->autoneg_advertised & ADVERTISE_100_FULL) { + DEBUGOUT("Advertise 100mb Full duplex\n"); + mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS; + } + + /* We do not allow the Phy to advertise 1000 Mb Half Duplex */ + if (hw->autoneg_advertised & ADVERTISE_1000_HALF) { + DEBUGOUT("Advertise 1000mb Half duplex requested, request denied!\n"); + } + + /* Do we want to advertise 1000 Mb Full Duplex? */ + if (hw->autoneg_advertised & ADVERTISE_1000_FULL) { + DEBUGOUT("Advertise 1000mb Full duplex\n"); + mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS; + if (hw->phy_type == e1000_phy_ife) { + DEBUGOUT("e1000_phy_ife is a 10/100 PHY. Gigabit speed is not supported.\n"); + } + } + + /* Check for a software override of the flow control settings, and + * setup the PHY advertisement registers accordingly. If + * auto-negotiation is enabled, then software will have to set the + * "PAUSE" bits to the correct value in the Auto-Negotiation + * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-negotiation. + * + * The possible values of the "fc" parameter are: + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause frames + * but not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames + * but we do not support receiving pause frames). + * 3: Both Rx and TX flow control (symmetric) are enabled. + * other: No software override. The flow control configuration + * in the EEPROM is used. + */ + switch (hw->fc) { + case E1000_FC_NONE: /* 0 */ + /* Flow control (RX & TX) is completely disabled by a + * software over-ride. + */ + mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); + break; + case E1000_FC_RX_PAUSE: /* 1 */ + /* RX Flow control is enabled, and TX Flow control is + * disabled, by a software over-ride. + */ + /* Since there really isn't a way to advertise that we are + * capable of RX Pause ONLY, we will advertise that we + * support both symmetric and asymmetric RX PAUSE. Later + * (in e1000_config_fc_after_link_up) we will disable the + *hw's ability to send PAUSE frames. + */ + mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); + break; + case E1000_FC_TX_PAUSE: /* 2 */ + /* TX Flow control is enabled, and RX Flow control is + * disabled, by a software over-ride. + */ + mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR; + mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE; + break; + case E1000_FC_FULL: /* 3 */ + /* Flow control (both RX and TX) is enabled by a software + * over-ride. + */ + mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); + break; + default: + DEBUGOUT("Flow control param set incorrectly\n"); + return -E1000_ERR_CONFIG; + } + + ret_val = e1000_write_phy_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg); + if (ret_val) + return ret_val; + + DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg); + + if (hw->phy_type != e1000_phy_ife) { + ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg); + if (ret_val) + return ret_val; + } + + return E1000_SUCCESS; +} + +/****************************************************************************** +* Force PHY speed and duplex settings to hw->forced_speed_duplex +* +* hw - Struct containing variables accessed by shared code +******************************************************************************/ +static int32_t +e1000_phy_force_speed_duplex(struct e1000_hw *hw) +{ + uint32_t ctrl; + int32_t ret_val; + uint16_t mii_ctrl_reg; + uint16_t mii_status_reg; + uint16_t phy_data; + uint16_t i; + + DEBUGFUNC("e1000_phy_force_speed_duplex"); + + /* Turn off Flow control if we are forcing speed and duplex. */ + hw->fc = E1000_FC_NONE; + + DEBUGOUT1("hw->fc = %d\n", hw->fc); + + /* Read the Device Control Register. */ + ctrl = E1000_READ_REG(hw, CTRL); + + /* Set the bits to Force Speed and Duplex in the Device Ctrl Reg. */ + ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); + ctrl &= ~(DEVICE_SPEED_MASK); + + /* Clear the Auto Speed Detect Enable bit. */ + ctrl &= ~E1000_CTRL_ASDE; + + /* Read the MII Control Register. */ + ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &mii_ctrl_reg); + if (ret_val) + return ret_val; + + /* We need to disable autoneg in order to force link and duplex. */ + + mii_ctrl_reg &= ~MII_CR_AUTO_NEG_EN; + + /* Are we forcing Full or Half Duplex? */ + if (hw->forced_speed_duplex == e1000_100_full || + hw->forced_speed_duplex == e1000_10_full) { + /* We want to force full duplex so we SET the full duplex bits in the + * Device and MII Control Registers. + */ + ctrl |= E1000_CTRL_FD; + mii_ctrl_reg |= MII_CR_FULL_DUPLEX; + DEBUGOUT("Full Duplex\n"); + } else { + /* We want to force half duplex so we CLEAR the full duplex bits in + * the Device and MII Control Registers. + */ + ctrl &= ~E1000_CTRL_FD; + mii_ctrl_reg &= ~MII_CR_FULL_DUPLEX; + DEBUGOUT("Half Duplex\n"); + } + + /* Are we forcing 100Mbps??? */ + if (hw->forced_speed_duplex == e1000_100_full || + hw->forced_speed_duplex == e1000_100_half) { + /* Set the 100Mb bit and turn off the 1000Mb and 10Mb bits. */ + ctrl |= E1000_CTRL_SPD_100; + mii_ctrl_reg |= MII_CR_SPEED_100; + mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_10); + DEBUGOUT("Forcing 100mb "); + } else { + /* Set the 10Mb bit and turn off the 1000Mb and 100Mb bits. */ + ctrl &= ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100); + mii_ctrl_reg |= MII_CR_SPEED_10; + mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_100); + DEBUGOUT("Forcing 10mb "); + } + + e1000_config_collision_dist(hw); + + /* Write the configured values back to the Device Control Reg. */ + E1000_WRITE_REG(hw, CTRL, ctrl); + + if ((hw->phy_type == e1000_phy_m88) || + (hw->phy_type == e1000_phy_gg82563)) { + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + return ret_val; + + /* Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI + * forced whenever speed are duplex are forced. + */ + phy_data &= ~M88E1000_PSCR_AUTO_X_MODE; + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); + if (ret_val) + return ret_val; + + DEBUGOUT1("M88E1000 PSCR: %x \n", phy_data); + + /* Need to reset the PHY or these changes will be ignored */ + mii_ctrl_reg |= MII_CR_RESET; + + /* Disable MDI-X support for 10/100 */ + } else if (hw->phy_type == e1000_phy_ife) { + ret_val = e1000_read_phy_reg(hw, IFE_PHY_MDIX_CONTROL, &phy_data); + if (ret_val) + return ret_val; + + phy_data &= ~IFE_PMC_AUTO_MDIX; + phy_data &= ~IFE_PMC_FORCE_MDIX; + + ret_val = e1000_write_phy_reg(hw, IFE_PHY_MDIX_CONTROL, phy_data); + if (ret_val) + return ret_val; + + } else { + /* Clear Auto-Crossover to force MDI manually. IGP requires MDI + * forced whenever speed or duplex are forced. + */ + ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data); + if (ret_val) + return ret_val; + + phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX; + phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX; + + ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data); + if (ret_val) + return ret_val; + } + + /* Write back the modified PHY MII control register. */ + ret_val = e1000_write_phy_reg(hw, PHY_CTRL, mii_ctrl_reg); + if (ret_val) + return ret_val; + + udelay(1); + + /* The wait_autoneg_complete flag may be a little misleading here. + * Since we are forcing speed and duplex, Auto-Neg is not enabled. + * But we do want to delay for a period while forcing only so we + * don't generate false No Link messages. So we will wait here + * only if the user has set wait_autoneg_complete to 1, which is + * the default. + */ + if (hw->wait_autoneg_complete) { + /* We will wait for autoneg to complete. */ + DEBUGOUT("Waiting for forced speed/duplex link.\n"); + mii_status_reg = 0; + + /* We will wait for autoneg to complete or 4.5 seconds to expire. */ + for (i = PHY_FORCE_TIME; i > 0; i--) { + /* Read the MII Status Register and wait for Auto-Neg Complete bit + * to be set. + */ + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + return ret_val; + + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + return ret_val; + + if (mii_status_reg & MII_SR_LINK_STATUS) break; + msleep(100); + } + if ((i == 0) && + ((hw->phy_type == e1000_phy_m88) || + (hw->phy_type == e1000_phy_gg82563))) { + /* We didn't get link. Reset the DSP and wait again for link. */ + ret_val = e1000_phy_reset_dsp(hw); + if (ret_val) { + DEBUGOUT("Error Resetting PHY DSP\n"); + return ret_val; + } + } + /* This loop will early-out if the link condition has been met. */ + for (i = PHY_FORCE_TIME; i > 0; i--) { + if (mii_status_reg & MII_SR_LINK_STATUS) break; + msleep(100); + /* Read the MII Status Register and wait for Auto-Neg Complete bit + * to be set. + */ + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + return ret_val; + + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + return ret_val; + } + } + + if (hw->phy_type == e1000_phy_m88) { + /* Because we reset the PHY above, we need to re-force TX_CLK in the + * Extended PHY Specific Control Register to 25MHz clock. This value + * defaults back to a 2.5MHz clock when the PHY is reset. + */ + ret_val = e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + return ret_val; + + phy_data |= M88E1000_EPSCR_TX_CLK_25; + ret_val = e1000_write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, phy_data); + if (ret_val) + return ret_val; + + /* In addition, because of the s/w reset above, we need to enable CRS on + * TX. This must be set for both full and half duplex operation. + */ + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + return ret_val; + + phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX; + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); + if (ret_val) + return ret_val; + + if ((hw->mac_type == e1000_82544 || hw->mac_type == e1000_82543) && + (!hw->autoneg) && (hw->forced_speed_duplex == e1000_10_full || + hw->forced_speed_duplex == e1000_10_half)) { + ret_val = e1000_polarity_reversal_workaround(hw); + if (ret_val) + return ret_val; + } + } else if (hw->phy_type == e1000_phy_gg82563) { + /* The TX_CLK of the Extended PHY Specific Control Register defaults + * to 2.5MHz on a reset. We need to re-force it back to 25MHz, if + * we're not in a forced 10/duplex configuration. */ + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, &phy_data); + if (ret_val) + return ret_val; + + phy_data &= ~GG82563_MSCR_TX_CLK_MASK; + if ((hw->forced_speed_duplex == e1000_10_full) || + (hw->forced_speed_duplex == e1000_10_half)) + phy_data |= GG82563_MSCR_TX_CLK_10MBPS_2_5MHZ; + else + phy_data |= GG82563_MSCR_TX_CLK_100MBPS_25MHZ; + + /* Also due to the reset, we need to enable CRS on Tx. */ + phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX; + + ret_val = e1000_write_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, phy_data); + if (ret_val) + return ret_val; + } + return E1000_SUCCESS; +} + +/****************************************************************************** +* Sets the collision distance in the Transmit Control register +* +* hw - Struct containing variables accessed by shared code +* +* Link should have been established previously. Reads the speed and duplex +* information from the Device Status register. +******************************************************************************/ +void +e1000_config_collision_dist(struct e1000_hw *hw) +{ + uint32_t tctl, coll_dist; + + DEBUGFUNC("e1000_config_collision_dist"); + + if (hw->mac_type < e1000_82543) + coll_dist = E1000_COLLISION_DISTANCE_82542; + else + coll_dist = E1000_COLLISION_DISTANCE; + + tctl = E1000_READ_REG(hw, TCTL); + + tctl &= ~E1000_TCTL_COLD; + tctl |= coll_dist << E1000_COLD_SHIFT; + + E1000_WRITE_REG(hw, TCTL, tctl); + E1000_WRITE_FLUSH(hw); +} + +/****************************************************************************** +* Sets MAC speed and duplex settings to reflect the those in the PHY +* +* hw - Struct containing variables accessed by shared code +* mii_reg - data to write to the MII control register +* +* The contents of the PHY register containing the needed information need to +* be passed in. +******************************************************************************/ +static int32_t +e1000_config_mac_to_phy(struct e1000_hw *hw) +{ + uint32_t ctrl; + int32_t ret_val; + uint16_t phy_data; + + DEBUGFUNC("e1000_config_mac_to_phy"); + + /* 82544 or newer MAC, Auto Speed Detection takes care of + * MAC speed/duplex configuration.*/ + if (hw->mac_type >= e1000_82544) + return E1000_SUCCESS; + + /* Read the Device Control Register and set the bits to Force Speed + * and Duplex. + */ + ctrl = E1000_READ_REG(hw, CTRL); + ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); + ctrl &= ~(E1000_CTRL_SPD_SEL | E1000_CTRL_ILOS); + + /* Set up duplex in the Device Control and Transmit Control + * registers depending on negotiated values. + */ + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data); + if (ret_val) + return ret_val; + + if (phy_data & M88E1000_PSSR_DPLX) + ctrl |= E1000_CTRL_FD; + else + ctrl &= ~E1000_CTRL_FD; + + e1000_config_collision_dist(hw); + + /* Set up speed in the Device Control register depending on + * negotiated values. + */ + if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) + ctrl |= E1000_CTRL_SPD_1000; + else if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS) + ctrl |= E1000_CTRL_SPD_100; + + /* Write the configured values back to the Device Control Reg. */ + E1000_WRITE_REG(hw, CTRL, ctrl); + return E1000_SUCCESS; +} + +/****************************************************************************** + * Forces the MAC's flow control settings. + * + * hw - Struct containing variables accessed by shared code + * + * Sets the TFCE and RFCE bits in the device control register to reflect + * the adapter settings. TFCE and RFCE need to be explicitly set by + * software when a Copper PHY is used because autonegotiation is managed + * by the PHY rather than the MAC. Software must also configure these + * bits when link is forced on a fiber connection. + *****************************************************************************/ +int32_t +e1000_force_mac_fc(struct e1000_hw *hw) +{ + uint32_t ctrl; + + DEBUGFUNC("e1000_force_mac_fc"); + + /* Get the current configuration of the Device Control Register */ + ctrl = E1000_READ_REG(hw, CTRL); + + /* Because we didn't get link via the internal auto-negotiation + * mechanism (we either forced link or we got link via PHY + * auto-neg), we have to manually enable/disable transmit an + * receive flow control. + * + * The "Case" statement below enables/disable flow control + * according to the "hw->fc" parameter. + * + * The possible values of the "fc" parameter are: + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause + * frames but not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames + * frames but we do not receive pause frames). + * 3: Both Rx and TX flow control (symmetric) is enabled. + * other: No other values should be possible at this point. + */ + + switch (hw->fc) { + case E1000_FC_NONE: + ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE)); + break; + case E1000_FC_RX_PAUSE: + ctrl &= (~E1000_CTRL_TFCE); + ctrl |= E1000_CTRL_RFCE; + break; + case E1000_FC_TX_PAUSE: + ctrl &= (~E1000_CTRL_RFCE); + ctrl |= E1000_CTRL_TFCE; + break; + case E1000_FC_FULL: + ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE); + break; + default: + DEBUGOUT("Flow control param set incorrectly\n"); + return -E1000_ERR_CONFIG; + } + + /* Disable TX Flow Control for 82542 (rev 2.0) */ + if (hw->mac_type == e1000_82542_rev2_0) + ctrl &= (~E1000_CTRL_TFCE); + + E1000_WRITE_REG(hw, CTRL, ctrl); + return E1000_SUCCESS; +} + +/****************************************************************************** + * Configures flow control settings after link is established + * + * hw - Struct containing variables accessed by shared code + * + * Should be called immediately after a valid link has been established. + * Forces MAC flow control settings if link was forced. When in MII/GMII mode + * and autonegotiation is enabled, the MAC flow control settings will be set + * based on the flow control negotiated by the PHY. In TBI mode, the TFCE + * and RFCE bits will be automaticaly set to the negotiated flow control mode. + *****************************************************************************/ +static int32_t +e1000_config_fc_after_link_up(struct e1000_hw *hw) +{ + int32_t ret_val; + uint16_t mii_status_reg; + uint16_t mii_nway_adv_reg; + uint16_t mii_nway_lp_ability_reg; + uint16_t speed; + uint16_t duplex; + + DEBUGFUNC("e1000_config_fc_after_link_up"); + + /* Check for the case where we have fiber media and auto-neg failed + * so we had to force link. In this case, we need to force the + * configuration of the MAC to match the "fc" parameter. + */ + if (((hw->media_type == e1000_media_type_fiber) && (hw->autoneg_failed)) || + ((hw->media_type == e1000_media_type_internal_serdes) && + (hw->autoneg_failed)) || + ((hw->media_type == e1000_media_type_copper) && (!hw->autoneg))) { + ret_val = e1000_force_mac_fc(hw); + if (ret_val) { + DEBUGOUT("Error forcing flow control settings\n"); + return ret_val; + } + } + + /* Check for the case where we have copper media and auto-neg is + * enabled. In this case, we need to check and see if Auto-Neg + * has completed, and if so, how the PHY and link partner has + * flow control configured. + */ + if ((hw->media_type == e1000_media_type_copper) && hw->autoneg) { + /* Read the MII Status Register and check to see if AutoNeg + * has completed. We read this twice because this reg has + * some "sticky" (latched) bits. + */ + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + return ret_val; + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + return ret_val; + + if (mii_status_reg & MII_SR_AUTONEG_COMPLETE) { + /* The AutoNeg process has completed, so we now need to + * read both the Auto Negotiation Advertisement Register + * (Address 4) and the Auto_Negotiation Base Page Ability + * Register (Address 5) to determine how flow control was + * negotiated. + */ + ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, + &mii_nway_adv_reg); + if (ret_val) + return ret_val; + ret_val = e1000_read_phy_reg(hw, PHY_LP_ABILITY, + &mii_nway_lp_ability_reg); + if (ret_val) + return ret_val; + + /* Two bits in the Auto Negotiation Advertisement Register + * (Address 4) and two bits in the Auto Negotiation Base + * Page Ability Register (Address 5) determine flow control + * for both the PHY and the link partner. The following + * table, taken out of the IEEE 802.3ab/D6.0 dated March 25, + * 1999, describes these PAUSE resolution bits and how flow + * control is determined based upon these settings. + * NOTE: DC = Don't Care + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution + *-------|---------|-------|---------|-------------------- + * 0 | 0 | DC | DC | E1000_FC_NONE + * 0 | 1 | 0 | DC | E1000_FC_NONE + * 0 | 1 | 1 | 0 | E1000_FC_NONE + * 0 | 1 | 1 | 1 | E1000_FC_TX_PAUSE + * 1 | 0 | 0 | DC | E1000_FC_NONE + * 1 | DC | 1 | DC | E1000_FC_FULL + * 1 | 1 | 0 | 0 | E1000_FC_NONE + * 1 | 1 | 0 | 1 | E1000_FC_RX_PAUSE + * + */ + /* Are both PAUSE bits set to 1? If so, this implies + * Symmetric Flow Control is enabled at both ends. The + * ASM_DIR bits are irrelevant per the spec. + * + * For Symmetric Flow Control: + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result + *-------|---------|-------|---------|-------------------- + * 1 | DC | 1 | DC | E1000_FC_FULL + * + */ + if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && + (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) { + /* Now we need to check if the user selected RX ONLY + * of pause frames. In this case, we had to advertise + * FULL flow control because we could not advertise RX + * ONLY. Hence, we must now check to see if we need to + * turn OFF the TRANSMISSION of PAUSE frames. + */ + if (hw->original_fc == E1000_FC_FULL) { + hw->fc = E1000_FC_FULL; + DEBUGOUT("Flow Control = FULL.\n"); + } else { + hw->fc = E1000_FC_RX_PAUSE; + DEBUGOUT("Flow Control = RX PAUSE frames only.\n"); + } + } + /* For receiving PAUSE frames ONLY. + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result + *-------|---------|-------|---------|-------------------- + * 0 | 1 | 1 | 1 | E1000_FC_TX_PAUSE + * + */ + else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) && + (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && + (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && + (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { + hw->fc = E1000_FC_TX_PAUSE; + DEBUGOUT("Flow Control = TX PAUSE frames only.\n"); + } + /* For transmitting PAUSE frames ONLY. + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result + *-------|---------|-------|---------|-------------------- + * 1 | 1 | 0 | 1 | E1000_FC_RX_PAUSE + * + */ + else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && + (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && + !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && + (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { + hw->fc = E1000_FC_RX_PAUSE; + DEBUGOUT("Flow Control = RX PAUSE frames only.\n"); + } + /* Per the IEEE spec, at this point flow control should be + * disabled. However, we want to consider that we could + * be connected to a legacy switch that doesn't advertise + * desired flow control, but can be forced on the link + * partner. So if we advertised no flow control, that is + * what we will resolve to. If we advertised some kind of + * receive capability (Rx Pause Only or Full Flow Control) + * and the link partner advertised none, we will configure + * ourselves to enable Rx Flow Control only. We can do + * this safely for two reasons: If the link partner really + * didn't want flow control enabled, and we enable Rx, no + * harm done since we won't be receiving any PAUSE frames + * anyway. If the intent on the link partner was to have + * flow control enabled, then by us enabling RX only, we + * can at least receive pause frames and process them. + * This is a good idea because in most cases, since we are + * predominantly a server NIC, more times than not we will + * be asked to delay transmission of packets than asking + * our link partner to pause transmission of frames. + */ + else if ((hw->original_fc == E1000_FC_NONE || + hw->original_fc == E1000_FC_TX_PAUSE) || + hw->fc_strict_ieee) { + hw->fc = E1000_FC_NONE; + DEBUGOUT("Flow Control = NONE.\n"); + } else { + hw->fc = E1000_FC_RX_PAUSE; + DEBUGOUT("Flow Control = RX PAUSE frames only.\n"); + } + + /* Now we need to do one last check... If we auto- + * negotiated to HALF DUPLEX, flow control should not be + * enabled per IEEE 802.3 spec. + */ + ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex); + if (ret_val) { + DEBUGOUT("Error getting link speed and duplex\n"); + return ret_val; + } + + if (duplex == HALF_DUPLEX) + hw->fc = E1000_FC_NONE; + + /* Now we call a subroutine to actually force the MAC + * controller to use the correct flow control settings. + */ + ret_val = e1000_force_mac_fc(hw); + if (ret_val) { + DEBUGOUT("Error forcing flow control settings\n"); + return ret_val; + } + } else { + DEBUGOUT("Copper PHY and Auto Neg has not completed.\n"); + } + } + return E1000_SUCCESS; +} + +/****************************************************************************** + * Checks to see if the link status of the hardware has changed. + * + * hw - Struct containing variables accessed by shared code + * + * Called by any function that needs to check the link status of the adapter. + *****************************************************************************/ +int32_t +e1000_check_for_link(struct e1000_hw *hw) +{ + uint32_t rxcw = 0; + uint32_t ctrl; + uint32_t status; + uint32_t rctl; + uint32_t icr; + uint32_t signal = 0; + int32_t ret_val; + uint16_t phy_data; + + DEBUGFUNC("e1000_check_for_link"); + + ctrl = E1000_READ_REG(hw, CTRL); + status = E1000_READ_REG(hw, STATUS); + + /* On adapters with a MAC newer than 82544, SW Defineable pin 1 will be + * set when the optics detect a signal. On older adapters, it will be + * cleared when there is a signal. This applies to fiber media only. + */ + if ((hw->media_type == e1000_media_type_fiber) || + (hw->media_type == e1000_media_type_internal_serdes)) { + rxcw = E1000_READ_REG(hw, RXCW); + + if (hw->media_type == e1000_media_type_fiber) { + signal = (hw->mac_type > e1000_82544) ? E1000_CTRL_SWDPIN1 : 0; + if (status & E1000_STATUS_LU) + hw->get_link_status = FALSE; + } + } + + /* If we have a copper PHY then we only want to go out to the PHY + * registers to see if Auto-Neg has completed and/or if our link + * status has changed. The get_link_status flag will be set if we + * receive a Link Status Change interrupt or we have Rx Sequence + * Errors. + */ + if ((hw->media_type == e1000_media_type_copper) && hw->get_link_status) { + /* First we want to see if the MII Status Register reports + * link. If so, then we want to get the current speed/duplex + * of the PHY. + * Read the register twice since the link bit is sticky. + */ + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); + if (ret_val) + return ret_val; + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); + if (ret_val) + return ret_val; + + if (phy_data & MII_SR_LINK_STATUS) { + hw->get_link_status = FALSE; + /* Check if there was DownShift, must be checked immediately after + * link-up */ + e1000_check_downshift(hw); + + /* If we are on 82544 or 82543 silicon and speed/duplex + * are forced to 10H or 10F, then we will implement the polarity + * reversal workaround. We disable interrupts first, and upon + * returning, place the devices interrupt state to its previous + * value except for the link status change interrupt which will + * happen due to the execution of this workaround. + */ + + if ((hw->mac_type == e1000_82544 || hw->mac_type == e1000_82543) && + (!hw->autoneg) && + (hw->forced_speed_duplex == e1000_10_full || + hw->forced_speed_duplex == e1000_10_half)) { + E1000_WRITE_REG(hw, IMC, 0xffffffff); + ret_val = e1000_polarity_reversal_workaround(hw); + icr = E1000_READ_REG(hw, ICR); + E1000_WRITE_REG(hw, ICS, (icr & ~E1000_ICS_LSC)); + E1000_WRITE_REG(hw, IMS, IMS_ENABLE_MASK); + } + + } else { + /* No link detected */ + e1000_config_dsp_after_link_change(hw, FALSE); + return 0; + } + + /* If we are forcing speed/duplex, then we simply return since + * we have already determined whether we have link or not. + */ + if (!hw->autoneg) return -E1000_ERR_CONFIG; + + /* optimize the dsp settings for the igp phy */ + e1000_config_dsp_after_link_change(hw, TRUE); + + /* We have a M88E1000 PHY and Auto-Neg is enabled. If we + * have Si on board that is 82544 or newer, Auto + * Speed Detection takes care of MAC speed/duplex + * configuration. So we only need to configure Collision + * Distance in the MAC. Otherwise, we need to force + * speed/duplex on the MAC to the current PHY speed/duplex + * settings. + */ + if (hw->mac_type >= e1000_82544) + e1000_config_collision_dist(hw); + else { + ret_val = e1000_config_mac_to_phy(hw); + if (ret_val) { + DEBUGOUT("Error configuring MAC to PHY settings\n"); + return ret_val; + } + } + + /* Configure Flow Control now that Auto-Neg has completed. First, we + * need to restore the desired flow control settings because we may + * have had to re-autoneg with a different link partner. + */ + ret_val = e1000_config_fc_after_link_up(hw); + if (ret_val) { + DEBUGOUT("Error configuring flow control\n"); + return ret_val; + } + + /* At this point we know that we are on copper and we have + * auto-negotiated link. These are conditions for checking the link + * partner capability register. We use the link speed to determine if + * TBI compatibility needs to be turned on or off. If the link is not + * at gigabit speed, then TBI compatibility is not needed. If we are + * at gigabit speed, we turn on TBI compatibility. + */ + if (hw->tbi_compatibility_en) { + uint16_t speed, duplex; + ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex); + if (ret_val) { + DEBUGOUT("Error getting link speed and duplex\n"); + return ret_val; + } + if (speed != SPEED_1000) { + /* If link speed is not set to gigabit speed, we do not need + * to enable TBI compatibility. + */ + if (hw->tbi_compatibility_on) { + /* If we previously were in the mode, turn it off. */ + rctl = E1000_READ_REG(hw, RCTL); + rctl &= ~E1000_RCTL_SBP; + E1000_WRITE_REG(hw, RCTL, rctl); + hw->tbi_compatibility_on = FALSE; + } + } else { + /* If TBI compatibility is was previously off, turn it on. For + * compatibility with a TBI link partner, we will store bad + * packets. Some frames have an additional byte on the end and + * will look like CRC errors to to the hardware. + */ + if (!hw->tbi_compatibility_on) { + hw->tbi_compatibility_on = TRUE; + rctl = E1000_READ_REG(hw, RCTL); + rctl |= E1000_RCTL_SBP; + E1000_WRITE_REG(hw, RCTL, rctl); + } + } + } + } + /* If we don't have link (auto-negotiation failed or link partner cannot + * auto-negotiate), the cable is plugged in (we have signal), and our + * link partner is not trying to auto-negotiate with us (we are receiving + * idles or data), we need to force link up. We also need to give + * auto-negotiation time to complete, in case the cable was just plugged + * in. The autoneg_failed flag does this. + */ + else if ((((hw->media_type == e1000_media_type_fiber) && + ((ctrl & E1000_CTRL_SWDPIN1) == signal)) || + (hw->media_type == e1000_media_type_internal_serdes)) && + (!(status & E1000_STATUS_LU)) && + (!(rxcw & E1000_RXCW_C))) { + if (hw->autoneg_failed == 0) { + hw->autoneg_failed = 1; + return 0; + } + DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\n"); + + /* Disable auto-negotiation in the TXCW register */ + E1000_WRITE_REG(hw, TXCW, (hw->txcw & ~E1000_TXCW_ANE)); + + /* Force link-up and also force full-duplex. */ + ctrl = E1000_READ_REG(hw, CTRL); + ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD); + E1000_WRITE_REG(hw, CTRL, ctrl); + + /* Configure Flow Control after forcing link up. */ + ret_val = e1000_config_fc_after_link_up(hw); + if (ret_val) { + DEBUGOUT("Error configuring flow control\n"); + return ret_val; + } + } + /* If we are forcing link and we are receiving /C/ ordered sets, re-enable + * auto-negotiation in the TXCW register and disable forced link in the + * Device Control register in an attempt to auto-negotiate with our link + * partner. + */ + else if (((hw->media_type == e1000_media_type_fiber) || + (hw->media_type == e1000_media_type_internal_serdes)) && + (ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) { + DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\n"); + E1000_WRITE_REG(hw, TXCW, hw->txcw); + E1000_WRITE_REG(hw, CTRL, (ctrl & ~E1000_CTRL_SLU)); + + hw->serdes_link_down = FALSE; + } + /* If we force link for non-auto-negotiation switch, check link status + * based on MAC synchronization for internal serdes media type. + */ + else if ((hw->media_type == e1000_media_type_internal_serdes) && + !(E1000_TXCW_ANE & E1000_READ_REG(hw, TXCW))) { + /* SYNCH bit and IV bit are sticky. */ + udelay(10); + if (E1000_RXCW_SYNCH & E1000_READ_REG(hw, RXCW)) { + if (!(rxcw & E1000_RXCW_IV)) { + hw->serdes_link_down = FALSE; + DEBUGOUT("SERDES: Link is up.\n"); + } + } else { + hw->serdes_link_down = TRUE; + DEBUGOUT("SERDES: Link is down.\n"); + } + } + if ((hw->media_type == e1000_media_type_internal_serdes) && + (E1000_TXCW_ANE & E1000_READ_REG(hw, TXCW))) { + hw->serdes_link_down = !(E1000_STATUS_LU & E1000_READ_REG(hw, STATUS)); + } + return E1000_SUCCESS; +} + +/****************************************************************************** + * Detects the current speed and duplex settings of the hardware. + * + * hw - Struct containing variables accessed by shared code + * speed - Speed of the connection + * duplex - Duplex setting of the connection + *****************************************************************************/ +int32_t +e1000_get_speed_and_duplex(struct e1000_hw *hw, + uint16_t *speed, + uint16_t *duplex) +{ + uint32_t status; + int32_t ret_val; + uint16_t phy_data; + + DEBUGFUNC("e1000_get_speed_and_duplex"); + + if (hw->mac_type >= e1000_82543) { + status = E1000_READ_REG(hw, STATUS); + if (status & E1000_STATUS_SPEED_1000) { + *speed = SPEED_1000; + DEBUGOUT("1000 Mbs, "); + } else if (status & E1000_STATUS_SPEED_100) { + *speed = SPEED_100; + DEBUGOUT("100 Mbs, "); + } else { + *speed = SPEED_10; + DEBUGOUT("10 Mbs, "); + } + + if (status & E1000_STATUS_FD) { + *duplex = FULL_DUPLEX; + DEBUGOUT("Full Duplex\n"); + } else { + *duplex = HALF_DUPLEX; + DEBUGOUT(" Half Duplex\n"); + } + } else { + DEBUGOUT("1000 Mbs, Full Duplex\n"); + *speed = SPEED_1000; + *duplex = FULL_DUPLEX; + } + + /* IGP01 PHY may advertise full duplex operation after speed downgrade even + * if it is operating at half duplex. Here we set the duplex settings to + * match the duplex in the link partner's capabilities. + */ + if (hw->phy_type == e1000_phy_igp && hw->speed_downgraded) { + ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_EXP, &phy_data); + if (ret_val) + return ret_val; + + if (!(phy_data & NWAY_ER_LP_NWAY_CAPS)) + *duplex = HALF_DUPLEX; + else { + ret_val = e1000_read_phy_reg(hw, PHY_LP_ABILITY, &phy_data); + if (ret_val) + return ret_val; + if ((*speed == SPEED_100 && !(phy_data & NWAY_LPAR_100TX_FD_CAPS)) || + (*speed == SPEED_10 && !(phy_data & NWAY_LPAR_10T_FD_CAPS))) + *duplex = HALF_DUPLEX; + } + } + + if ((hw->mac_type == e1000_80003es2lan) && + (hw->media_type == e1000_media_type_copper)) { + if (*speed == SPEED_1000) + ret_val = e1000_configure_kmrn_for_1000(hw); + else + ret_val = e1000_configure_kmrn_for_10_100(hw, *duplex); + if (ret_val) + return ret_val; + } + + if ((hw->phy_type == e1000_phy_igp_3) && (*speed == SPEED_1000)) { + ret_val = e1000_kumeran_lock_loss_workaround(hw); + if (ret_val) + return ret_val; + } + + return E1000_SUCCESS; +} + +/****************************************************************************** +* Blocks until autoneg completes or times out (~4.5 seconds) +* +* hw - Struct containing variables accessed by shared code +******************************************************************************/ +static int32_t +e1000_wait_autoneg(struct e1000_hw *hw) +{ + int32_t ret_val; + uint16_t i; + uint16_t phy_data; + + DEBUGFUNC("e1000_wait_autoneg"); + DEBUGOUT("Waiting for Auto-Neg to complete.\n"); + + /* We will wait for autoneg to complete or 4.5 seconds to expire. */ + for (i = PHY_AUTO_NEG_TIME; i > 0; i--) { + /* Read the MII Status Register and wait for Auto-Neg + * Complete bit to be set. + */ + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); + if (ret_val) + return ret_val; + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); + if (ret_val) + return ret_val; + if (phy_data & MII_SR_AUTONEG_COMPLETE) { + return E1000_SUCCESS; + } + msleep(100); + } + return E1000_SUCCESS; +} + +/****************************************************************************** +* Raises the Management Data Clock +* +* hw - Struct containing variables accessed by shared code +* ctrl - Device control register's current value +******************************************************************************/ +static void +e1000_raise_mdi_clk(struct e1000_hw *hw, + uint32_t *ctrl) +{ + /* Raise the clock input to the Management Data Clock (by setting the MDC + * bit), and then delay 10 microseconds. + */ + E1000_WRITE_REG(hw, CTRL, (*ctrl | E1000_CTRL_MDC)); + E1000_WRITE_FLUSH(hw); + udelay(10); +} + +/****************************************************************************** +* Lowers the Management Data Clock +* +* hw - Struct containing variables accessed by shared code +* ctrl - Device control register's current value +******************************************************************************/ +static void +e1000_lower_mdi_clk(struct e1000_hw *hw, + uint32_t *ctrl) +{ + /* Lower the clock input to the Management Data Clock (by clearing the MDC + * bit), and then delay 10 microseconds. + */ + E1000_WRITE_REG(hw, CTRL, (*ctrl & ~E1000_CTRL_MDC)); + E1000_WRITE_FLUSH(hw); + udelay(10); +} + +/****************************************************************************** +* Shifts data bits out to the PHY +* +* hw - Struct containing variables accessed by shared code +* data - Data to send out to the PHY +* count - Number of bits to shift out +* +* Bits are shifted out in MSB to LSB order. +******************************************************************************/ +static void +e1000_shift_out_mdi_bits(struct e1000_hw *hw, + uint32_t data, + uint16_t count) +{ + uint32_t ctrl; + uint32_t mask; + + /* We need to shift "count" number of bits out to the PHY. So, the value + * in the "data" parameter will be shifted out to the PHY one bit at a + * time. In order to do this, "data" must be broken down into bits. + */ + mask = 0x01; + mask <<= (count - 1); + + ctrl = E1000_READ_REG(hw, CTRL); + + /* Set MDIO_DIR and MDC_DIR direction bits to be used as output pins. */ + ctrl |= (E1000_CTRL_MDIO_DIR | E1000_CTRL_MDC_DIR); + + while (mask) { + /* A "1" is shifted out to the PHY by setting the MDIO bit to "1" and + * then raising and lowering the Management Data Clock. A "0" is + * shifted out to the PHY by setting the MDIO bit to "0" and then + * raising and lowering the clock. + */ + if (data & mask) + ctrl |= E1000_CTRL_MDIO; + else + ctrl &= ~E1000_CTRL_MDIO; + + E1000_WRITE_REG(hw, CTRL, ctrl); + E1000_WRITE_FLUSH(hw); + + udelay(10); + + e1000_raise_mdi_clk(hw, &ctrl); + e1000_lower_mdi_clk(hw, &ctrl); + + mask = mask >> 1; + } +} + +/****************************************************************************** +* Shifts data bits in from the PHY +* +* hw - Struct containing variables accessed by shared code +* +* Bits are shifted in in MSB to LSB order. +******************************************************************************/ +static uint16_t +e1000_shift_in_mdi_bits(struct e1000_hw *hw) +{ + uint32_t ctrl; + uint16_t data = 0; + uint8_t i; + + /* In order to read a register from the PHY, we need to shift in a total + * of 18 bits from the PHY. The first two bit (turnaround) times are used + * to avoid contention on the MDIO pin when a read operation is performed. + * These two bits are ignored by us and thrown away. Bits are "shifted in" + * by raising the input to the Management Data Clock (setting the MDC bit), + * and then reading the value of the MDIO bit. + */ + ctrl = E1000_READ_REG(hw, CTRL); + + /* Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as input. */ + ctrl &= ~E1000_CTRL_MDIO_DIR; + ctrl &= ~E1000_CTRL_MDIO; + + E1000_WRITE_REG(hw, CTRL, ctrl); + E1000_WRITE_FLUSH(hw); + + /* Raise and Lower the clock before reading in the data. This accounts for + * the turnaround bits. The first clock occurred when we clocked out the + * last bit of the Register Address. + */ + e1000_raise_mdi_clk(hw, &ctrl); + e1000_lower_mdi_clk(hw, &ctrl); + + for (data = 0, i = 0; i < 16; i++) { + data = data << 1; + e1000_raise_mdi_clk(hw, &ctrl); + ctrl = E1000_READ_REG(hw, CTRL); + /* Check to see if we shifted in a "1". */ + if (ctrl & E1000_CTRL_MDIO) + data |= 1; + e1000_lower_mdi_clk(hw, &ctrl); + } + + e1000_raise_mdi_clk(hw, &ctrl); + e1000_lower_mdi_clk(hw, &ctrl); + + return data; +} + +static int32_t +e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask) +{ + uint32_t swfw_sync = 0; + uint32_t swmask = mask; + uint32_t fwmask = mask << 16; + int32_t timeout = 200; + + DEBUGFUNC("e1000_swfw_sync_acquire"); + + if (hw->swfwhw_semaphore_present) + return e1000_get_software_flag(hw); + + if (!hw->swfw_sync_present) + return e1000_get_hw_eeprom_semaphore(hw); + + while (timeout) { + if (e1000_get_hw_eeprom_semaphore(hw)) + return -E1000_ERR_SWFW_SYNC; + + swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC); + if (!(swfw_sync & (fwmask | swmask))) { + break; + } + + /* firmware currently using resource (fwmask) */ + /* or other software thread currently using resource (swmask) */ + e1000_put_hw_eeprom_semaphore(hw); + mdelay(5); + timeout--; + } + + if (!timeout) { + DEBUGOUT("Driver can't access resource, SW_FW_SYNC timeout.\n"); + return -E1000_ERR_SWFW_SYNC; + } + + swfw_sync |= swmask; + E1000_WRITE_REG(hw, SW_FW_SYNC, swfw_sync); + + e1000_put_hw_eeprom_semaphore(hw); + return E1000_SUCCESS; +} + +static void +e1000_swfw_sync_release(struct e1000_hw *hw, uint16_t mask) +{ + uint32_t swfw_sync; + uint32_t swmask = mask; + + DEBUGFUNC("e1000_swfw_sync_release"); + + if (hw->swfwhw_semaphore_present) { + e1000_release_software_flag(hw); + return; + } + + if (!hw->swfw_sync_present) { + e1000_put_hw_eeprom_semaphore(hw); + return; + } + + /* if (e1000_get_hw_eeprom_semaphore(hw)) + * return -E1000_ERR_SWFW_SYNC; */ + while (e1000_get_hw_eeprom_semaphore(hw) != E1000_SUCCESS); + /* empty */ + + swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC); + swfw_sync &= ~swmask; + E1000_WRITE_REG(hw, SW_FW_SYNC, swfw_sync); + + e1000_put_hw_eeprom_semaphore(hw); +} + +/***************************************************************************** +* Reads the value from a PHY register, if the value is on a specific non zero +* page, sets the page first. +* hw - Struct containing variables accessed by shared code +* reg_addr - address of the PHY register to read +******************************************************************************/ +int32_t +e1000_read_phy_reg(struct e1000_hw *hw, + uint32_t reg_addr, + uint16_t *phy_data) +{ + uint32_t ret_val; + uint16_t swfw; + + DEBUGFUNC("e1000_read_phy_reg"); + + if ((hw->mac_type == e1000_80003es2lan) && + (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) { + swfw = E1000_SWFW_PHY1_SM; + } else { + swfw = E1000_SWFW_PHY0_SM; + } + if (e1000_swfw_sync_acquire(hw, swfw)) + return -E1000_ERR_SWFW_SYNC; + + if ((hw->phy_type == e1000_phy_igp || + hw->phy_type == e1000_phy_igp_3 || + hw->phy_type == e1000_phy_igp_2) && + (reg_addr > MAX_PHY_MULTI_PAGE_REG)) { + ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT, + (uint16_t)reg_addr); + if (ret_val) { + e1000_swfw_sync_release(hw, swfw); + return ret_val; + } + } else if (hw->phy_type == e1000_phy_gg82563) { + if (((reg_addr & MAX_PHY_REG_ADDRESS) > MAX_PHY_MULTI_PAGE_REG) || + (hw->mac_type == e1000_80003es2lan)) { + /* Select Configuration Page */ + if ((reg_addr & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) { + ret_val = e1000_write_phy_reg_ex(hw, GG82563_PHY_PAGE_SELECT, + (uint16_t)((uint16_t)reg_addr >> GG82563_PAGE_SHIFT)); + } else { + /* Use Alternative Page Select register to access + * registers 30 and 31 + */ + ret_val = e1000_write_phy_reg_ex(hw, + GG82563_PHY_PAGE_SELECT_ALT, + (uint16_t)((uint16_t)reg_addr >> GG82563_PAGE_SHIFT)); + } + + if (ret_val) { + e1000_swfw_sync_release(hw, swfw); + return ret_val; + } + } + } + + ret_val = e1000_read_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr, + phy_data); + + e1000_swfw_sync_release(hw, swfw); + return ret_val; +} + +static int32_t +e1000_read_phy_reg_ex(struct e1000_hw *hw, uint32_t reg_addr, + uint16_t *phy_data) +{ + uint32_t i; + uint32_t mdic = 0; + const uint32_t phy_addr = 1; + + DEBUGFUNC("e1000_read_phy_reg_ex"); + + if (reg_addr > MAX_PHY_REG_ADDRESS) { + DEBUGOUT1("PHY Address %d is out of range\n", reg_addr); + return -E1000_ERR_PARAM; + } + + if (hw->mac_type > e1000_82543) { + /* Set up Op-code, Phy Address, and register address in the MDI + * Control register. The MAC will take care of interfacing with the + * PHY to retrieve the desired data. + */ + mdic = ((reg_addr << E1000_MDIC_REG_SHIFT) | + (phy_addr << E1000_MDIC_PHY_SHIFT) | + (E1000_MDIC_OP_READ)); + + E1000_WRITE_REG(hw, MDIC, mdic); + + /* Poll the ready bit to see if the MDI read completed */ + for (i = 0; i < 64; i++) { + udelay(50); + mdic = E1000_READ_REG(hw, MDIC); + if (mdic & E1000_MDIC_READY) break; + } + if (!(mdic & E1000_MDIC_READY)) { + DEBUGOUT("MDI Read did not complete\n"); + return -E1000_ERR_PHY; + } + if (mdic & E1000_MDIC_ERROR) { + DEBUGOUT("MDI Error\n"); + return -E1000_ERR_PHY; + } + *phy_data = (uint16_t) mdic; + } else { + /* We must first send a preamble through the MDIO pin to signal the + * beginning of an MII instruction. This is done by sending 32 + * consecutive "1" bits. + */ + e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE); + + /* Now combine the next few fields that are required for a read + * operation. We use this method instead of calling the + * e1000_shift_out_mdi_bits routine five different times. The format of + * a MII read instruction consists of a shift out of 14 bits and is + * defined as follows: + * + * followed by a shift in of 18 bits. This first two bits shifted in + * are TurnAround bits used to avoid contention on the MDIO pin when a + * READ operation is performed. These two bits are thrown away + * followed by a shift in of 16 bits which contains the desired data. + */ + mdic = ((reg_addr) | (phy_addr << 5) | + (PHY_OP_READ << 10) | (PHY_SOF << 12)); + + e1000_shift_out_mdi_bits(hw, mdic, 14); + + /* Now that we've shifted out the read command to the MII, we need to + * "shift in" the 16-bit value (18 total bits) of the requested PHY + * register address. + */ + *phy_data = e1000_shift_in_mdi_bits(hw); + } + return E1000_SUCCESS; +} + +/****************************************************************************** +* Writes a value to a PHY register +* +* hw - Struct containing variables accessed by shared code +* reg_addr - address of the PHY register to write +* data - data to write to the PHY +******************************************************************************/ +int32_t +e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, + uint16_t phy_data) +{ + uint32_t ret_val; + uint16_t swfw; + + DEBUGFUNC("e1000_write_phy_reg"); + + if ((hw->mac_type == e1000_80003es2lan) && + (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) { + swfw = E1000_SWFW_PHY1_SM; + } else { + swfw = E1000_SWFW_PHY0_SM; + } + if (e1000_swfw_sync_acquire(hw, swfw)) + return -E1000_ERR_SWFW_SYNC; + + if ((hw->phy_type == e1000_phy_igp || + hw->phy_type == e1000_phy_igp_3 || + hw->phy_type == e1000_phy_igp_2) && + (reg_addr > MAX_PHY_MULTI_PAGE_REG)) { + ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT, + (uint16_t)reg_addr); + if (ret_val) { + e1000_swfw_sync_release(hw, swfw); + return ret_val; + } + } else if (hw->phy_type == e1000_phy_gg82563) { + if (((reg_addr & MAX_PHY_REG_ADDRESS) > MAX_PHY_MULTI_PAGE_REG) || + (hw->mac_type == e1000_80003es2lan)) { + /* Select Configuration Page */ + if ((reg_addr & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) { + ret_val = e1000_write_phy_reg_ex(hw, GG82563_PHY_PAGE_SELECT, + (uint16_t)((uint16_t)reg_addr >> GG82563_PAGE_SHIFT)); + } else { + /* Use Alternative Page Select register to access + * registers 30 and 31 + */ + ret_val = e1000_write_phy_reg_ex(hw, + GG82563_PHY_PAGE_SELECT_ALT, + (uint16_t)((uint16_t)reg_addr >> GG82563_PAGE_SHIFT)); + } + + if (ret_val) { + e1000_swfw_sync_release(hw, swfw); + return ret_val; + } + } + } + + ret_val = e1000_write_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr, + phy_data); + + e1000_swfw_sync_release(hw, swfw); + return ret_val; +} + +static int32_t +e1000_write_phy_reg_ex(struct e1000_hw *hw, uint32_t reg_addr, + uint16_t phy_data) +{ + uint32_t i; + uint32_t mdic = 0; + const uint32_t phy_addr = 1; + + DEBUGFUNC("e1000_write_phy_reg_ex"); + + if (reg_addr > MAX_PHY_REG_ADDRESS) { + DEBUGOUT1("PHY Address %d is out of range\n", reg_addr); + return -E1000_ERR_PARAM; + } + + if (hw->mac_type > e1000_82543) { + /* Set up Op-code, Phy Address, register address, and data intended + * for the PHY register in the MDI Control register. The MAC will take + * care of interfacing with the PHY to send the desired data. + */ + mdic = (((uint32_t) phy_data) | + (reg_addr << E1000_MDIC_REG_SHIFT) | + (phy_addr << E1000_MDIC_PHY_SHIFT) | + (E1000_MDIC_OP_WRITE)); + + E1000_WRITE_REG(hw, MDIC, mdic); + + /* Poll the ready bit to see if the MDI read completed */ + for (i = 0; i < 641; i++) { + udelay(5); + mdic = E1000_READ_REG(hw, MDIC); + if (mdic & E1000_MDIC_READY) break; + } + if (!(mdic & E1000_MDIC_READY)) { + DEBUGOUT("MDI Write did not complete\n"); + return -E1000_ERR_PHY; + } + } else { + /* We'll need to use the SW defined pins to shift the write command + * out to the PHY. We first send a preamble to the PHY to signal the + * beginning of the MII instruction. This is done by sending 32 + * consecutive "1" bits. + */ + e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE); + + /* Now combine the remaining required fields that will indicate a + * write operation. We use this method instead of calling the + * e1000_shift_out_mdi_bits routine for each field in the command. The + * format of a MII write instruction is as follows: + * . + */ + mdic = ((PHY_TURNAROUND) | (reg_addr << 2) | (phy_addr << 7) | + (PHY_OP_WRITE << 12) | (PHY_SOF << 14)); + mdic <<= 16; + mdic |= (uint32_t) phy_data; + + e1000_shift_out_mdi_bits(hw, mdic, 32); + } + + return E1000_SUCCESS; +} + +static int32_t +e1000_read_kmrn_reg(struct e1000_hw *hw, + uint32_t reg_addr, + uint16_t *data) +{ + uint32_t reg_val; + uint16_t swfw; + DEBUGFUNC("e1000_read_kmrn_reg"); + + if ((hw->mac_type == e1000_80003es2lan) && + (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) { + swfw = E1000_SWFW_PHY1_SM; + } else { + swfw = E1000_SWFW_PHY0_SM; + } + if (e1000_swfw_sync_acquire(hw, swfw)) + return -E1000_ERR_SWFW_SYNC; + + /* Write register address */ + reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) & + E1000_KUMCTRLSTA_OFFSET) | + E1000_KUMCTRLSTA_REN; + E1000_WRITE_REG(hw, KUMCTRLSTA, reg_val); + udelay(2); + + /* Read the data returned */ + reg_val = E1000_READ_REG(hw, KUMCTRLSTA); + *data = (uint16_t)reg_val; + + e1000_swfw_sync_release(hw, swfw); + return E1000_SUCCESS; +} + +static int32_t +e1000_write_kmrn_reg(struct e1000_hw *hw, + uint32_t reg_addr, + uint16_t data) +{ + uint32_t reg_val; + uint16_t swfw; + DEBUGFUNC("e1000_write_kmrn_reg"); + + if ((hw->mac_type == e1000_80003es2lan) && + (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) { + swfw = E1000_SWFW_PHY1_SM; + } else { + swfw = E1000_SWFW_PHY0_SM; + } + if (e1000_swfw_sync_acquire(hw, swfw)) + return -E1000_ERR_SWFW_SYNC; + + reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) & + E1000_KUMCTRLSTA_OFFSET) | data; + E1000_WRITE_REG(hw, KUMCTRLSTA, reg_val); + udelay(2); + + e1000_swfw_sync_release(hw, swfw); + return E1000_SUCCESS; +} + +/****************************************************************************** +* Returns the PHY to the power-on reset state +* +* hw - Struct containing variables accessed by shared code +******************************************************************************/ +int32_t +e1000_phy_hw_reset(struct e1000_hw *hw) +{ + uint32_t ctrl, ctrl_ext; + uint32_t led_ctrl; + int32_t ret_val; + uint16_t swfw; + + DEBUGFUNC("e1000_phy_hw_reset"); + + /* In the case of the phy reset being blocked, it's not an error, we + * simply return success without performing the reset. */ + ret_val = e1000_check_phy_reset_block(hw); + if (ret_val) + return E1000_SUCCESS; + + DEBUGOUT("Resetting Phy...\n"); + + if (hw->mac_type > e1000_82543) { + if ((hw->mac_type == e1000_80003es2lan) && + (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) { + swfw = E1000_SWFW_PHY1_SM; + } else { + swfw = E1000_SWFW_PHY0_SM; + } + if (e1000_swfw_sync_acquire(hw, swfw)) { + DEBUGOUT("Unable to acquire swfw sync\n"); + return -E1000_ERR_SWFW_SYNC; + } + /* Read the device control register and assert the E1000_CTRL_PHY_RST + * bit. Then, take it out of reset. + * For pre-e1000_82571 hardware, we delay for 10ms between the assert + * and deassert. For e1000_82571 hardware and later, we instead delay + * for 50us between and 10ms after the deassertion. + */ + ctrl = E1000_READ_REG(hw, CTRL); + E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PHY_RST); + E1000_WRITE_FLUSH(hw); + + if (hw->mac_type < e1000_82571) + msleep(10); + else + udelay(100); + + E1000_WRITE_REG(hw, CTRL, ctrl); + E1000_WRITE_FLUSH(hw); + + if (hw->mac_type >= e1000_82571) + mdelay(10); + + e1000_swfw_sync_release(hw, swfw); + } else { + /* Read the Extended Device Control Register, assert the PHY_RESET_DIR + * bit to put the PHY into reset. Then, take it out of reset. + */ + ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); + ctrl_ext |= E1000_CTRL_EXT_SDP4_DIR; + ctrl_ext &= ~E1000_CTRL_EXT_SDP4_DATA; + E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); + E1000_WRITE_FLUSH(hw); + msleep(10); + ctrl_ext |= E1000_CTRL_EXT_SDP4_DATA; + E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); + E1000_WRITE_FLUSH(hw); + } + udelay(150); + + if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) { + /* Configure activity LED after PHY reset */ + led_ctrl = E1000_READ_REG(hw, LEDCTL); + led_ctrl &= IGP_ACTIVITY_LED_MASK; + led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); + E1000_WRITE_REG(hw, LEDCTL, led_ctrl); + } + + /* Wait for FW to finish PHY configuration. */ + ret_val = e1000_get_phy_cfg_done(hw); + if (ret_val != E1000_SUCCESS) + return ret_val; + e1000_release_software_semaphore(hw); + + if ((hw->mac_type == e1000_ich8lan) && (hw->phy_type == e1000_phy_igp_3)) + ret_val = e1000_init_lcd_from_nvm(hw); + + return ret_val; +} + +/****************************************************************************** +* Resets the PHY +* +* hw - Struct containing variables accessed by shared code +* +* Sets bit 15 of the MII Control register +******************************************************************************/ +int32_t +e1000_phy_reset(struct e1000_hw *hw) +{ + int32_t ret_val; + uint16_t phy_data; + + DEBUGFUNC("e1000_phy_reset"); + + /* In the case of the phy reset being blocked, it's not an error, we + * simply return success without performing the reset. */ + ret_val = e1000_check_phy_reset_block(hw); + if (ret_val) + return E1000_SUCCESS; + + switch (hw->phy_type) { + case e1000_phy_igp: + case e1000_phy_igp_2: + case e1000_phy_igp_3: + case e1000_phy_ife: + ret_val = e1000_phy_hw_reset(hw); + if (ret_val) + return ret_val; + break; + default: + ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data); + if (ret_val) + return ret_val; + + phy_data |= MII_CR_RESET; + ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data); + if (ret_val) + return ret_val; + + udelay(1); + break; + } + + if (hw->phy_type == e1000_phy_igp || hw->phy_type == e1000_phy_igp_2) + e1000_phy_init_script(hw); + + return E1000_SUCCESS; +} + +/****************************************************************************** +* Work-around for 82566 power-down: on D3 entry- +* 1) disable gigabit link +* 2) write VR power-down enable +* 3) read it back +* if successful continue, else issue LCD reset and repeat +* +* hw - struct containing variables accessed by shared code +******************************************************************************/ +void +e1000_phy_powerdown_workaround(struct e1000_hw *hw) +{ + int32_t reg; + uint16_t phy_data; + int32_t retry = 0; + + DEBUGFUNC("e1000_phy_powerdown_workaround"); + + if (hw->phy_type != e1000_phy_igp_3) + return; + + do { + /* Disable link */ + reg = E1000_READ_REG(hw, PHY_CTRL); + E1000_WRITE_REG(hw, PHY_CTRL, reg | E1000_PHY_CTRL_GBE_DISABLE | + E1000_PHY_CTRL_NOND0A_GBE_DISABLE); + + /* Write VR power-down enable - bits 9:8 should be 10b */ + e1000_read_phy_reg(hw, IGP3_VR_CTRL, &phy_data); + phy_data |= (1 << 9); + phy_data &= ~(1 << 8); + e1000_write_phy_reg(hw, IGP3_VR_CTRL, phy_data); + + /* Read it back and test */ + e1000_read_phy_reg(hw, IGP3_VR_CTRL, &phy_data); + if (((phy_data & IGP3_VR_CTRL_MODE_MASK) == IGP3_VR_CTRL_MODE_SHUT) || retry) + break; + + /* Issue PHY reset and repeat at most one more time */ + reg = E1000_READ_REG(hw, CTRL); + E1000_WRITE_REG(hw, CTRL, reg | E1000_CTRL_PHY_RST); + retry++; + } while (retry); + + return; + +} + +/****************************************************************************** +* Work-around for 82566 Kumeran PCS lock loss: +* On link status change (i.e. PCI reset, speed change) and link is up and +* speed is gigabit- +* 0) if workaround is optionally disabled do nothing +* 1) wait 1ms for Kumeran link to come up +* 2) check Kumeran Diagnostic register PCS lock loss bit +* 3) if not set the link is locked (all is good), otherwise... +* 4) reset the PHY +* 5) repeat up to 10 times +* Note: this is only called for IGP3 copper when speed is 1gb. +* +* hw - struct containing variables accessed by shared code +******************************************************************************/ +static int32_t +e1000_kumeran_lock_loss_workaround(struct e1000_hw *hw) +{ + int32_t ret_val; + int32_t reg; + int32_t cnt; + uint16_t phy_data; + + if (hw->kmrn_lock_loss_workaround_disabled) + return E1000_SUCCESS; + + /* Make sure link is up before proceeding. If not just return. + * Attempting this while link is negotiating fouled up link + * stability */ + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); + + if (phy_data & MII_SR_LINK_STATUS) { + for (cnt = 0; cnt < 10; cnt++) { + /* read once to clear */ + ret_val = e1000_read_phy_reg(hw, IGP3_KMRN_DIAG, &phy_data); + if (ret_val) + return ret_val; + /* and again to get new status */ + ret_val = e1000_read_phy_reg(hw, IGP3_KMRN_DIAG, &phy_data); + if (ret_val) + return ret_val; + + /* check for PCS lock */ + if (!(phy_data & IGP3_KMRN_DIAG_PCS_LOCK_LOSS)) + return E1000_SUCCESS; + + /* Issue PHY reset */ + e1000_phy_hw_reset(hw); + mdelay(5); + } + /* Disable GigE link negotiation */ + reg = E1000_READ_REG(hw, PHY_CTRL); + E1000_WRITE_REG(hw, PHY_CTRL, reg | E1000_PHY_CTRL_GBE_DISABLE | + E1000_PHY_CTRL_NOND0A_GBE_DISABLE); + + /* unable to acquire PCS lock */ + return E1000_ERR_PHY; + } + + return E1000_SUCCESS; +} + +/****************************************************************************** +* Probes the expected PHY address for known PHY IDs +* +* hw - Struct containing variables accessed by shared code +******************************************************************************/ +static int32_t +e1000_detect_gig_phy(struct e1000_hw *hw) +{ + int32_t phy_init_status, ret_val; + uint16_t phy_id_high, phy_id_low; + boolean_t match = FALSE; + + DEBUGFUNC("e1000_detect_gig_phy"); + + if (hw->phy_id != 0) + return E1000_SUCCESS; + + /* The 82571 firmware may still be configuring the PHY. In this + * case, we cannot access the PHY until the configuration is done. So + * we explicitly set the PHY values. */ + if (hw->mac_type == e1000_82571 || + hw->mac_type == e1000_82572) { + hw->phy_id = IGP01E1000_I_PHY_ID; + hw->phy_type = e1000_phy_igp_2; + return E1000_SUCCESS; + } + + /* ESB-2 PHY reads require e1000_phy_gg82563 to be set because of a work- + * around that forces PHY page 0 to be set or the reads fail. The rest of + * the code in this routine uses e1000_read_phy_reg to read the PHY ID. + * So for ESB-2 we need to have this set so our reads won't fail. If the + * attached PHY is not a e1000_phy_gg82563, the routines below will figure + * this out as well. */ + if (hw->mac_type == e1000_80003es2lan) + hw->phy_type = e1000_phy_gg82563; + + /* Read the PHY ID Registers to identify which PHY is onboard. */ + ret_val = e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high); + if (ret_val) + return ret_val; + + hw->phy_id = (uint32_t) (phy_id_high << 16); + udelay(20); + ret_val = e1000_read_phy_reg(hw, PHY_ID2, &phy_id_low); + if (ret_val) + return ret_val; + + hw->phy_id |= (uint32_t) (phy_id_low & PHY_REVISION_MASK); + hw->phy_revision = (uint32_t) phy_id_low & ~PHY_REVISION_MASK; + + switch (hw->mac_type) { + case e1000_82543: + if (hw->phy_id == M88E1000_E_PHY_ID) match = TRUE; + break; + case e1000_82544: + if (hw->phy_id == M88E1000_I_PHY_ID) match = TRUE; + break; + case e1000_82540: + case e1000_82545: + case e1000_82545_rev_3: + case e1000_82546: + case e1000_82546_rev_3: + if (hw->phy_id == M88E1011_I_PHY_ID) match = TRUE; + break; + case e1000_82541: + case e1000_82541_rev_2: + case e1000_82547: + case e1000_82547_rev_2: + if (hw->phy_id == IGP01E1000_I_PHY_ID) match = TRUE; + break; + case e1000_82573: + if (hw->phy_id == M88E1111_I_PHY_ID) match = TRUE; + break; + case e1000_80003es2lan: + if (hw->phy_id == GG82563_E_PHY_ID) match = TRUE; + break; + case e1000_ich8lan: + if (hw->phy_id == IGP03E1000_E_PHY_ID) match = TRUE; + if (hw->phy_id == IFE_E_PHY_ID) match = TRUE; + if (hw->phy_id == IFE_PLUS_E_PHY_ID) match = TRUE; + if (hw->phy_id == IFE_C_E_PHY_ID) match = TRUE; + break; + default: + DEBUGOUT1("Invalid MAC type %d\n", hw->mac_type); + return -E1000_ERR_CONFIG; + } + phy_init_status = e1000_set_phy_type(hw); + + if ((match) && (phy_init_status == E1000_SUCCESS)) { + DEBUGOUT1("PHY ID 0x%X detected\n", hw->phy_id); + return E1000_SUCCESS; + } + DEBUGOUT1("Invalid PHY ID 0x%X\n", hw->phy_id); + return -E1000_ERR_PHY; +} + +/****************************************************************************** +* Resets the PHY's DSP +* +* hw - Struct containing variables accessed by shared code +******************************************************************************/ +static int32_t +e1000_phy_reset_dsp(struct e1000_hw *hw) +{ + int32_t ret_val; + DEBUGFUNC("e1000_phy_reset_dsp"); + + do { + if (hw->phy_type != e1000_phy_gg82563) { + ret_val = e1000_write_phy_reg(hw, 29, 0x001d); + if (ret_val) break; + } + ret_val = e1000_write_phy_reg(hw, 30, 0x00c1); + if (ret_val) break; + ret_val = e1000_write_phy_reg(hw, 30, 0x0000); + if (ret_val) break; + ret_val = E1000_SUCCESS; + } while (0); + + return ret_val; +} + +/****************************************************************************** +* Get PHY information from various PHY registers for igp PHY only. +* +* hw - Struct containing variables accessed by shared code +* phy_info - PHY information structure +******************************************************************************/ +static int32_t +e1000_phy_igp_get_info(struct e1000_hw *hw, + struct e1000_phy_info *phy_info) +{ + int32_t ret_val; + uint16_t phy_data, min_length, max_length, average; + e1000_rev_polarity polarity; + + DEBUGFUNC("e1000_phy_igp_get_info"); + + /* The downshift status is checked only once, after link is established, + * and it stored in the hw->speed_downgraded parameter. */ + phy_info->downshift = (e1000_downshift)hw->speed_downgraded; + + /* IGP01E1000 does not need to support it. */ + phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_normal; + + /* IGP01E1000 always correct polarity reversal */ + phy_info->polarity_correction = e1000_polarity_reversal_enabled; + + /* Check polarity status */ + ret_val = e1000_check_polarity(hw, &polarity); + if (ret_val) + return ret_val; + + phy_info->cable_polarity = polarity; + + ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS, &phy_data); + if (ret_val) + return ret_val; + + phy_info->mdix_mode = (e1000_auto_x_mode)((phy_data & IGP01E1000_PSSR_MDIX) >> + IGP01E1000_PSSR_MDIX_SHIFT); + + if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) == + IGP01E1000_PSSR_SPEED_1000MBPS) { + /* Local/Remote Receiver Information are only valid at 1000 Mbps */ + ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data); + if (ret_val) + return ret_val; + + phy_info->local_rx = ((phy_data & SR_1000T_LOCAL_RX_STATUS) >> + SR_1000T_LOCAL_RX_STATUS_SHIFT) ? + e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok; + phy_info->remote_rx = ((phy_data & SR_1000T_REMOTE_RX_STATUS) >> + SR_1000T_REMOTE_RX_STATUS_SHIFT) ? + e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok; + + /* Get cable length */ + ret_val = e1000_get_cable_length(hw, &min_length, &max_length); + if (ret_val) + return ret_val; + + /* Translate to old method */ + average = (max_length + min_length) / 2; + + if (average <= e1000_igp_cable_length_50) + phy_info->cable_length = e1000_cable_length_50; + else if (average <= e1000_igp_cable_length_80) + phy_info->cable_length = e1000_cable_length_50_80; + else if (average <= e1000_igp_cable_length_110) + phy_info->cable_length = e1000_cable_length_80_110; + else if (average <= e1000_igp_cable_length_140) + phy_info->cable_length = e1000_cable_length_110_140; + else + phy_info->cable_length = e1000_cable_length_140; + } + + return E1000_SUCCESS; +} + +/****************************************************************************** +* Get PHY information from various PHY registers for ife PHY only. +* +* hw - Struct containing variables accessed by shared code +* phy_info - PHY information structure +******************************************************************************/ +static int32_t +e1000_phy_ife_get_info(struct e1000_hw *hw, + struct e1000_phy_info *phy_info) +{ + int32_t ret_val; + uint16_t phy_data; + e1000_rev_polarity polarity; + + DEBUGFUNC("e1000_phy_ife_get_info"); + + phy_info->downshift = (e1000_downshift)hw->speed_downgraded; + phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_normal; + + ret_val = e1000_read_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL, &phy_data); + if (ret_val) + return ret_val; + phy_info->polarity_correction = + ((phy_data & IFE_PSC_AUTO_POLARITY_DISABLE) >> + IFE_PSC_AUTO_POLARITY_DISABLE_SHIFT) ? + e1000_polarity_reversal_disabled : e1000_polarity_reversal_enabled; + + if (phy_info->polarity_correction == e1000_polarity_reversal_enabled) { + ret_val = e1000_check_polarity(hw, &polarity); + if (ret_val) + return ret_val; + } else { + /* Polarity is forced. */ + polarity = ((phy_data & IFE_PSC_FORCE_POLARITY) >> + IFE_PSC_FORCE_POLARITY_SHIFT) ? + e1000_rev_polarity_reversed : e1000_rev_polarity_normal; + } + phy_info->cable_polarity = polarity; + + ret_val = e1000_read_phy_reg(hw, IFE_PHY_MDIX_CONTROL, &phy_data); + if (ret_val) + return ret_val; + + phy_info->mdix_mode = (e1000_auto_x_mode) + ((phy_data & (IFE_PMC_AUTO_MDIX | IFE_PMC_FORCE_MDIX)) >> + IFE_PMC_MDIX_MODE_SHIFT); + + return E1000_SUCCESS; +} + +/****************************************************************************** +* Get PHY information from various PHY registers fot m88 PHY only. +* +* hw - Struct containing variables accessed by shared code +* phy_info - PHY information structure +******************************************************************************/ +static int32_t +e1000_phy_m88_get_info(struct e1000_hw *hw, + struct e1000_phy_info *phy_info) +{ + int32_t ret_val; + uint16_t phy_data; + e1000_rev_polarity polarity; + + DEBUGFUNC("e1000_phy_m88_get_info"); + + /* The downshift status is checked only once, after link is established, + * and it stored in the hw->speed_downgraded parameter. */ + phy_info->downshift = (e1000_downshift)hw->speed_downgraded; + + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + return ret_val; + + phy_info->extended_10bt_distance = + ((phy_data & M88E1000_PSCR_10BT_EXT_DIST_ENABLE) >> + M88E1000_PSCR_10BT_EXT_DIST_ENABLE_SHIFT) ? + e1000_10bt_ext_dist_enable_lower : e1000_10bt_ext_dist_enable_normal; + + phy_info->polarity_correction = + ((phy_data & M88E1000_PSCR_POLARITY_REVERSAL) >> + M88E1000_PSCR_POLARITY_REVERSAL_SHIFT) ? + e1000_polarity_reversal_disabled : e1000_polarity_reversal_enabled; + + /* Check polarity status */ + ret_val = e1000_check_polarity(hw, &polarity); + if (ret_val) + return ret_val; + phy_info->cable_polarity = polarity; + + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data); + if (ret_val) + return ret_val; + + phy_info->mdix_mode = (e1000_auto_x_mode)((phy_data & M88E1000_PSSR_MDIX) >> + M88E1000_PSSR_MDIX_SHIFT); + + if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) { + /* Cable Length Estimation and Local/Remote Receiver Information + * are only valid at 1000 Mbps. + */ + if (hw->phy_type != e1000_phy_gg82563) { + phy_info->cable_length = (e1000_cable_length)((phy_data & M88E1000_PSSR_CABLE_LENGTH) >> + M88E1000_PSSR_CABLE_LENGTH_SHIFT); + } else { + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_DSP_DISTANCE, + &phy_data); + if (ret_val) + return ret_val; + + phy_info->cable_length = (e1000_cable_length)(phy_data & GG82563_DSPD_CABLE_LENGTH); + } + + ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data); + if (ret_val) + return ret_val; + + phy_info->local_rx = ((phy_data & SR_1000T_LOCAL_RX_STATUS) >> + SR_1000T_LOCAL_RX_STATUS_SHIFT) ? + e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok; + phy_info->remote_rx = ((phy_data & SR_1000T_REMOTE_RX_STATUS) >> + SR_1000T_REMOTE_RX_STATUS_SHIFT) ? + e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok; + + } + + return E1000_SUCCESS; +} + +/****************************************************************************** +* Get PHY information from various PHY registers +* +* hw - Struct containing variables accessed by shared code +* phy_info - PHY information structure +******************************************************************************/ +int32_t +e1000_phy_get_info(struct e1000_hw *hw, + struct e1000_phy_info *phy_info) +{ + int32_t ret_val; + uint16_t phy_data; + + DEBUGFUNC("e1000_phy_get_info"); + + phy_info->cable_length = e1000_cable_length_undefined; + phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_undefined; + phy_info->cable_polarity = e1000_rev_polarity_undefined; + phy_info->downshift = e1000_downshift_undefined; + phy_info->polarity_correction = e1000_polarity_reversal_undefined; + phy_info->mdix_mode = e1000_auto_x_mode_undefined; + phy_info->local_rx = e1000_1000t_rx_status_undefined; + phy_info->remote_rx = e1000_1000t_rx_status_undefined; + + if (hw->media_type != e1000_media_type_copper) { + DEBUGOUT("PHY info is only valid for copper media\n"); + return -E1000_ERR_CONFIG; + } + + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); + if (ret_val) + return ret_val; + + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); + if (ret_val) + return ret_val; + + if ((phy_data & MII_SR_LINK_STATUS) != MII_SR_LINK_STATUS) { + DEBUGOUT("PHY info is only valid if link is up\n"); + return -E1000_ERR_CONFIG; + } + + if (hw->phy_type == e1000_phy_igp || + hw->phy_type == e1000_phy_igp_3 || + hw->phy_type == e1000_phy_igp_2) + return e1000_phy_igp_get_info(hw, phy_info); + else if (hw->phy_type == e1000_phy_ife) + return e1000_phy_ife_get_info(hw, phy_info); + else + return e1000_phy_m88_get_info(hw, phy_info); +} + +int32_t +e1000_validate_mdi_setting(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_validate_mdi_settings"); + + if (!hw->autoneg && (hw->mdix == 0 || hw->mdix == 3)) { + DEBUGOUT("Invalid MDI setting detected\n"); + hw->mdix = 1; + return -E1000_ERR_CONFIG; + } + return E1000_SUCCESS; +} + + +/****************************************************************************** + * Sets up eeprom variables in the hw struct. Must be called after mac_type + * is configured. Additionally, if this is ICH8, the flash controller GbE + * registers must be mapped, or this will crash. + * + * hw - Struct containing variables accessed by shared code + *****************************************************************************/ +int32_t +e1000_init_eeprom_params(struct e1000_hw *hw) +{ + struct e1000_eeprom_info *eeprom = &hw->eeprom; + uint32_t eecd = E1000_READ_REG(hw, EECD); + int32_t ret_val = E1000_SUCCESS; + uint16_t eeprom_size; + + DEBUGFUNC("e1000_init_eeprom_params"); + + switch (hw->mac_type) { + case e1000_82542_rev2_0: + case e1000_82542_rev2_1: + case e1000_82543: + case e1000_82544: + eeprom->type = e1000_eeprom_microwire; + eeprom->word_size = 64; + eeprom->opcode_bits = 3; + eeprom->address_bits = 6; + eeprom->delay_usec = 50; + eeprom->use_eerd = FALSE; + eeprom->use_eewr = FALSE; + break; + case e1000_82540: + case e1000_82545: + case e1000_82545_rev_3: + case e1000_82546: + case e1000_82546_rev_3: + eeprom->type = e1000_eeprom_microwire; + eeprom->opcode_bits = 3; + eeprom->delay_usec = 50; + if (eecd & E1000_EECD_SIZE) { + eeprom->word_size = 256; + eeprom->address_bits = 8; + } else { + eeprom->word_size = 64; + eeprom->address_bits = 6; + } + eeprom->use_eerd = FALSE; + eeprom->use_eewr = FALSE; + break; + case e1000_82541: + case e1000_82541_rev_2: + case e1000_82547: + case e1000_82547_rev_2: + if (eecd & E1000_EECD_TYPE) { + eeprom->type = e1000_eeprom_spi; + eeprom->opcode_bits = 8; + eeprom->delay_usec = 1; + if (eecd & E1000_EECD_ADDR_BITS) { + eeprom->page_size = 32; + eeprom->address_bits = 16; + } else { + eeprom->page_size = 8; + eeprom->address_bits = 8; + } + } else { + eeprom->type = e1000_eeprom_microwire; + eeprom->opcode_bits = 3; + eeprom->delay_usec = 50; + if (eecd & E1000_EECD_ADDR_BITS) { + eeprom->word_size = 256; + eeprom->address_bits = 8; + } else { + eeprom->word_size = 64; + eeprom->address_bits = 6; + } + } + eeprom->use_eerd = FALSE; + eeprom->use_eewr = FALSE; + break; + case e1000_82571: + case e1000_82572: + eeprom->type = e1000_eeprom_spi; + eeprom->opcode_bits = 8; + eeprom->delay_usec = 1; + if (eecd & E1000_EECD_ADDR_BITS) { + eeprom->page_size = 32; + eeprom->address_bits = 16; + } else { + eeprom->page_size = 8; + eeprom->address_bits = 8; + } + eeprom->use_eerd = FALSE; + eeprom->use_eewr = FALSE; + break; + case e1000_82573: + eeprom->type = e1000_eeprom_spi; + eeprom->opcode_bits = 8; + eeprom->delay_usec = 1; + if (eecd & E1000_EECD_ADDR_BITS) { + eeprom->page_size = 32; + eeprom->address_bits = 16; + } else { + eeprom->page_size = 8; + eeprom->address_bits = 8; + } + eeprom->use_eerd = TRUE; + eeprom->use_eewr = TRUE; + if (e1000_is_onboard_nvm_eeprom(hw) == FALSE) { + eeprom->type = e1000_eeprom_flash; + eeprom->word_size = 2048; + + /* Ensure that the Autonomous FLASH update bit is cleared due to + * Flash update issue on parts which use a FLASH for NVM. */ + eecd &= ~E1000_EECD_AUPDEN; + E1000_WRITE_REG(hw, EECD, eecd); + } + break; + case e1000_80003es2lan: + eeprom->type = e1000_eeprom_spi; + eeprom->opcode_bits = 8; + eeprom->delay_usec = 1; + if (eecd & E1000_EECD_ADDR_BITS) { + eeprom->page_size = 32; + eeprom->address_bits = 16; + } else { + eeprom->page_size = 8; + eeprom->address_bits = 8; + } + eeprom->use_eerd = TRUE; + eeprom->use_eewr = FALSE; + break; + case e1000_ich8lan: + { + int32_t i = 0; + uint32_t flash_size = E1000_READ_ICH_FLASH_REG(hw, ICH_FLASH_GFPREG); + + eeprom->type = e1000_eeprom_ich8; + eeprom->use_eerd = FALSE; + eeprom->use_eewr = FALSE; + eeprom->word_size = E1000_SHADOW_RAM_WORDS; + + /* Zero the shadow RAM structure. But don't load it from NVM + * so as to save time for driver init */ + if (hw->eeprom_shadow_ram != NULL) { + for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) { + hw->eeprom_shadow_ram[i].modified = FALSE; + hw->eeprom_shadow_ram[i].eeprom_word = 0xFFFF; + } + } + + hw->flash_base_addr = (flash_size & ICH_GFPREG_BASE_MASK) * + ICH_FLASH_SECTOR_SIZE; + + hw->flash_bank_size = ((flash_size >> 16) & ICH_GFPREG_BASE_MASK) + 1; + hw->flash_bank_size -= (flash_size & ICH_GFPREG_BASE_MASK); + + hw->flash_bank_size *= ICH_FLASH_SECTOR_SIZE; + + hw->flash_bank_size /= 2 * sizeof(uint16_t); + + break; + } + default: + break; + } + + if (eeprom->type == e1000_eeprom_spi) { + /* eeprom_size will be an enum [0..8] that maps to eeprom sizes 128B to + * 32KB (incremented by powers of 2). + */ + if (hw->mac_type <= e1000_82547_rev_2) { + /* Set to default value for initial eeprom read. */ + eeprom->word_size = 64; + ret_val = e1000_read_eeprom(hw, EEPROM_CFG, 1, &eeprom_size); + if (ret_val) + return ret_val; + eeprom_size = (eeprom_size & EEPROM_SIZE_MASK) >> EEPROM_SIZE_SHIFT; + /* 256B eeprom size was not supported in earlier hardware, so we + * bump eeprom_size up one to ensure that "1" (which maps to 256B) + * is never the result used in the shifting logic below. */ + if (eeprom_size) + eeprom_size++; + } else { + eeprom_size = (uint16_t)((eecd & E1000_EECD_SIZE_EX_MASK) >> + E1000_EECD_SIZE_EX_SHIFT); + } + + eeprom->word_size = 1 << (eeprom_size + EEPROM_WORD_SIZE_SHIFT); + } + return ret_val; +} + +/****************************************************************************** + * Raises the EEPROM's clock input. + * + * hw - Struct containing variables accessed by shared code + * eecd - EECD's current value + *****************************************************************************/ +static void +e1000_raise_ee_clk(struct e1000_hw *hw, + uint32_t *eecd) +{ + /* Raise the clock input to the EEPROM (by setting the SK bit), and then + * wait microseconds. + */ + *eecd = *eecd | E1000_EECD_SK; + E1000_WRITE_REG(hw, EECD, *eecd); + E1000_WRITE_FLUSH(hw); + udelay(hw->eeprom.delay_usec); +} + +/****************************************************************************** + * Lowers the EEPROM's clock input. + * + * hw - Struct containing variables accessed by shared code + * eecd - EECD's current value + *****************************************************************************/ +static void +e1000_lower_ee_clk(struct e1000_hw *hw, + uint32_t *eecd) +{ + /* Lower the clock input to the EEPROM (by clearing the SK bit), and then + * wait 50 microseconds. + */ + *eecd = *eecd & ~E1000_EECD_SK; + E1000_WRITE_REG(hw, EECD, *eecd); + E1000_WRITE_FLUSH(hw); + udelay(hw->eeprom.delay_usec); +} + +/****************************************************************************** + * Shift data bits out to the EEPROM. + * + * hw - Struct containing variables accessed by shared code + * data - data to send to the EEPROM + * count - number of bits to shift out + *****************************************************************************/ +static void +e1000_shift_out_ee_bits(struct e1000_hw *hw, + uint16_t data, + uint16_t count) +{ + struct e1000_eeprom_info *eeprom = &hw->eeprom; + uint32_t eecd; + uint32_t mask; + + /* We need to shift "count" bits out to the EEPROM. So, value in the + * "data" parameter will be shifted out to the EEPROM one bit at a time. + * In order to do this, "data" must be broken down into bits. + */ + mask = 0x01 << (count - 1); + eecd = E1000_READ_REG(hw, EECD); + if (eeprom->type == e1000_eeprom_microwire) { + eecd &= ~E1000_EECD_DO; + } else if (eeprom->type == e1000_eeprom_spi) { + eecd |= E1000_EECD_DO; + } + do { + /* A "1" is shifted out to the EEPROM by setting bit "DI" to a "1", + * and then raising and then lowering the clock (the SK bit controls + * the clock input to the EEPROM). A "0" is shifted out to the EEPROM + * by setting "DI" to "0" and then raising and then lowering the clock. + */ + eecd &= ~E1000_EECD_DI; + + if (data & mask) + eecd |= E1000_EECD_DI; + + E1000_WRITE_REG(hw, EECD, eecd); + E1000_WRITE_FLUSH(hw); + + udelay(eeprom->delay_usec); + + e1000_raise_ee_clk(hw, &eecd); + e1000_lower_ee_clk(hw, &eecd); + + mask = mask >> 1; + + } while (mask); + + /* We leave the "DI" bit set to "0" when we leave this routine. */ + eecd &= ~E1000_EECD_DI; + E1000_WRITE_REG(hw, EECD, eecd); +} + +/****************************************************************************** + * Shift data bits in from the EEPROM + * + * hw - Struct containing variables accessed by shared code + *****************************************************************************/ +static uint16_t +e1000_shift_in_ee_bits(struct e1000_hw *hw, + uint16_t count) +{ + uint32_t eecd; + uint32_t i; + uint16_t data; + + /* In order to read a register from the EEPROM, we need to shift 'count' + * bits in from the EEPROM. Bits are "shifted in" by raising the clock + * input to the EEPROM (setting the SK bit), and then reading the value of + * the "DO" bit. During this "shifting in" process the "DI" bit should + * always be clear. + */ + + eecd = E1000_READ_REG(hw, EECD); + + eecd &= ~(E1000_EECD_DO | E1000_EECD_DI); + data = 0; + + for (i = 0; i < count; i++) { + data = data << 1; + e1000_raise_ee_clk(hw, &eecd); + + eecd = E1000_READ_REG(hw, EECD); + + eecd &= ~(E1000_EECD_DI); + if (eecd & E1000_EECD_DO) + data |= 1; + + e1000_lower_ee_clk(hw, &eecd); + } + + return data; +} + +/****************************************************************************** + * Prepares EEPROM for access + * + * hw - Struct containing variables accessed by shared code + * + * Lowers EEPROM clock. Clears input pin. Sets the chip select pin. This + * function should be called before issuing a command to the EEPROM. + *****************************************************************************/ +static int32_t +e1000_acquire_eeprom(struct e1000_hw *hw) +{ + struct e1000_eeprom_info *eeprom = &hw->eeprom; + uint32_t eecd, i=0; + + DEBUGFUNC("e1000_acquire_eeprom"); + + if (e1000_swfw_sync_acquire(hw, E1000_SWFW_EEP_SM)) + return -E1000_ERR_SWFW_SYNC; + eecd = E1000_READ_REG(hw, EECD); + + if (hw->mac_type != e1000_82573) { + /* Request EEPROM Access */ + if (hw->mac_type > e1000_82544) { + eecd |= E1000_EECD_REQ; + E1000_WRITE_REG(hw, EECD, eecd); + eecd = E1000_READ_REG(hw, EECD); + while ((!(eecd & E1000_EECD_GNT)) && + (i < E1000_EEPROM_GRANT_ATTEMPTS)) { + i++; + udelay(5); + eecd = E1000_READ_REG(hw, EECD); + } + if (!(eecd & E1000_EECD_GNT)) { + eecd &= ~E1000_EECD_REQ; + E1000_WRITE_REG(hw, EECD, eecd); + DEBUGOUT("Could not acquire EEPROM grant\n"); + e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM); + return -E1000_ERR_EEPROM; + } + } + } + + /* Setup EEPROM for Read/Write */ + + if (eeprom->type == e1000_eeprom_microwire) { + /* Clear SK and DI */ + eecd &= ~(E1000_EECD_DI | E1000_EECD_SK); + E1000_WRITE_REG(hw, EECD, eecd); + + /* Set CS */ + eecd |= E1000_EECD_CS; + E1000_WRITE_REG(hw, EECD, eecd); + } else if (eeprom->type == e1000_eeprom_spi) { + /* Clear SK and CS */ + eecd &= ~(E1000_EECD_CS | E1000_EECD_SK); + E1000_WRITE_REG(hw, EECD, eecd); + udelay(1); + } + + return E1000_SUCCESS; +} + +/****************************************************************************** + * Returns EEPROM to a "standby" state + * + * hw - Struct containing variables accessed by shared code + *****************************************************************************/ +static void +e1000_standby_eeprom(struct e1000_hw *hw) +{ + struct e1000_eeprom_info *eeprom = &hw->eeprom; + uint32_t eecd; + + eecd = E1000_READ_REG(hw, EECD); + + if (eeprom->type == e1000_eeprom_microwire) { + eecd &= ~(E1000_EECD_CS | E1000_EECD_SK); + E1000_WRITE_REG(hw, EECD, eecd); + E1000_WRITE_FLUSH(hw); + udelay(eeprom->delay_usec); + + /* Clock high */ + eecd |= E1000_EECD_SK; + E1000_WRITE_REG(hw, EECD, eecd); + E1000_WRITE_FLUSH(hw); + udelay(eeprom->delay_usec); + + /* Select EEPROM */ + eecd |= E1000_EECD_CS; + E1000_WRITE_REG(hw, EECD, eecd); + E1000_WRITE_FLUSH(hw); + udelay(eeprom->delay_usec); + + /* Clock low */ + eecd &= ~E1000_EECD_SK; + E1000_WRITE_REG(hw, EECD, eecd); + E1000_WRITE_FLUSH(hw); + udelay(eeprom->delay_usec); + } else if (eeprom->type == e1000_eeprom_spi) { + /* Toggle CS to flush commands */ + eecd |= E1000_EECD_CS; + E1000_WRITE_REG(hw, EECD, eecd); + E1000_WRITE_FLUSH(hw); + udelay(eeprom->delay_usec); + eecd &= ~E1000_EECD_CS; + E1000_WRITE_REG(hw, EECD, eecd); + E1000_WRITE_FLUSH(hw); + udelay(eeprom->delay_usec); + } +} + +/****************************************************************************** + * Terminates a command by inverting the EEPROM's chip select pin + * + * hw - Struct containing variables accessed by shared code + *****************************************************************************/ +static void +e1000_release_eeprom(struct e1000_hw *hw) +{ + uint32_t eecd; + + DEBUGFUNC("e1000_release_eeprom"); + + eecd = E1000_READ_REG(hw, EECD); + + if (hw->eeprom.type == e1000_eeprom_spi) { + eecd |= E1000_EECD_CS; /* Pull CS high */ + eecd &= ~E1000_EECD_SK; /* Lower SCK */ + + E1000_WRITE_REG(hw, EECD, eecd); + + udelay(hw->eeprom.delay_usec); + } else if (hw->eeprom.type == e1000_eeprom_microwire) { + /* cleanup eeprom */ + + /* CS on Microwire is active-high */ + eecd &= ~(E1000_EECD_CS | E1000_EECD_DI); + + E1000_WRITE_REG(hw, EECD, eecd); + + /* Rising edge of clock */ + eecd |= E1000_EECD_SK; + E1000_WRITE_REG(hw, EECD, eecd); + E1000_WRITE_FLUSH(hw); + udelay(hw->eeprom.delay_usec); + + /* Falling edge of clock */ + eecd &= ~E1000_EECD_SK; + E1000_WRITE_REG(hw, EECD, eecd); + E1000_WRITE_FLUSH(hw); + udelay(hw->eeprom.delay_usec); + } + + /* Stop requesting EEPROM access */ + if (hw->mac_type > e1000_82544) { + eecd &= ~E1000_EECD_REQ; + E1000_WRITE_REG(hw, EECD, eecd); + } + + e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM); +} + +/****************************************************************************** + * Reads a 16 bit word from the EEPROM. + * + * hw - Struct containing variables accessed by shared code + *****************************************************************************/ +static int32_t +e1000_spi_eeprom_ready(struct e1000_hw *hw) +{ + uint16_t retry_count = 0; + uint8_t spi_stat_reg; + + DEBUGFUNC("e1000_spi_eeprom_ready"); + + /* Read "Status Register" repeatedly until the LSB is cleared. The + * EEPROM will signal that the command has been completed by clearing + * bit 0 of the internal status register. If it's not cleared within + * 5 milliseconds, then error out. + */ + retry_count = 0; + do { + e1000_shift_out_ee_bits(hw, EEPROM_RDSR_OPCODE_SPI, + hw->eeprom.opcode_bits); + spi_stat_reg = (uint8_t)e1000_shift_in_ee_bits(hw, 8); + if (!(spi_stat_reg & EEPROM_STATUS_RDY_SPI)) + break; + + udelay(5); + retry_count += 5; + + e1000_standby_eeprom(hw); + } while (retry_count < EEPROM_MAX_RETRY_SPI); + + /* ATMEL SPI write time could vary from 0-20mSec on 3.3V devices (and + * only 0-5mSec on 5V devices) + */ + if (retry_count >= EEPROM_MAX_RETRY_SPI) { + DEBUGOUT("SPI EEPROM Status error\n"); + return -E1000_ERR_EEPROM; + } + + return E1000_SUCCESS; +} + +/****************************************************************************** + * Reads a 16 bit word from the EEPROM. + * + * hw - Struct containing variables accessed by shared code + * offset - offset of word in the EEPROM to read + * data - word read from the EEPROM + * words - number of words to read + *****************************************************************************/ +int32_t +e1000_read_eeprom(struct e1000_hw *hw, + uint16_t offset, + uint16_t words, + uint16_t *data) +{ + struct e1000_eeprom_info *eeprom = &hw->eeprom; + uint32_t i = 0; + + DEBUGFUNC("e1000_read_eeprom"); + + /* If eeprom is not yet detected, do so now */ + if (eeprom->word_size == 0) + e1000_init_eeprom_params(hw); + + /* A check for invalid values: offset too large, too many words, and not + * enough words. + */ + if ((offset >= eeprom->word_size) || (words > eeprom->word_size - offset) || + (words == 0)) { + DEBUGOUT2("\"words\" parameter out of bounds. Words = %d, size = %d\n", offset, eeprom->word_size); + return -E1000_ERR_EEPROM; + } + + /* EEPROM's that don't use EERD to read require us to bit-bang the SPI + * directly. In this case, we need to acquire the EEPROM so that + * FW or other port software does not interrupt. + */ + if (e1000_is_onboard_nvm_eeprom(hw) == TRUE && + hw->eeprom.use_eerd == FALSE) { + /* Prepare the EEPROM for bit-bang reading */ + if (e1000_acquire_eeprom(hw) != E1000_SUCCESS) + return -E1000_ERR_EEPROM; + } + + /* Eerd register EEPROM access requires no eeprom aquire/release */ + if (eeprom->use_eerd == TRUE) + return e1000_read_eeprom_eerd(hw, offset, words, data); + + /* ICH EEPROM access is done via the ICH flash controller */ + if (eeprom->type == e1000_eeprom_ich8) + return e1000_read_eeprom_ich8(hw, offset, words, data); + + /* Set up the SPI or Microwire EEPROM for bit-bang reading. We have + * acquired the EEPROM at this point, so any returns should relase it */ + if (eeprom->type == e1000_eeprom_spi) { + uint16_t word_in; + uint8_t read_opcode = EEPROM_READ_OPCODE_SPI; + + if (e1000_spi_eeprom_ready(hw)) { + e1000_release_eeprom(hw); + return -E1000_ERR_EEPROM; + } + + e1000_standby_eeprom(hw); + + /* Some SPI eeproms use the 8th address bit embedded in the opcode */ + if ((eeprom->address_bits == 8) && (offset >= 128)) + read_opcode |= EEPROM_A8_OPCODE_SPI; + + /* Send the READ command (opcode + addr) */ + e1000_shift_out_ee_bits(hw, read_opcode, eeprom->opcode_bits); + e1000_shift_out_ee_bits(hw, (uint16_t)(offset*2), eeprom->address_bits); + + /* Read the data. The address of the eeprom internally increments with + * each byte (spi) being read, saving on the overhead of eeprom setup + * and tear-down. The address counter will roll over if reading beyond + * the size of the eeprom, thus allowing the entire memory to be read + * starting from any offset. */ + for (i = 0; i < words; i++) { + word_in = e1000_shift_in_ee_bits(hw, 16); + data[i] = (word_in >> 8) | (word_in << 8); + } + } else if (eeprom->type == e1000_eeprom_microwire) { + for (i = 0; i < words; i++) { + /* Send the READ command (opcode + addr) */ + e1000_shift_out_ee_bits(hw, EEPROM_READ_OPCODE_MICROWIRE, + eeprom->opcode_bits); + e1000_shift_out_ee_bits(hw, (uint16_t)(offset + i), + eeprom->address_bits); + + /* Read the data. For microwire, each word requires the overhead + * of eeprom setup and tear-down. */ + data[i] = e1000_shift_in_ee_bits(hw, 16); + e1000_standby_eeprom(hw); + } + } + + /* End this read operation */ + e1000_release_eeprom(hw); + + return E1000_SUCCESS; +} + +/****************************************************************************** + * Reads a 16 bit word from the EEPROM using the EERD register. + * + * hw - Struct containing variables accessed by shared code + * offset - offset of word in the EEPROM to read + * data - word read from the EEPROM + * words - number of words to read + *****************************************************************************/ +static int32_t +e1000_read_eeprom_eerd(struct e1000_hw *hw, + uint16_t offset, + uint16_t words, + uint16_t *data) +{ + uint32_t i, eerd = 0; + int32_t error = 0; + + for (i = 0; i < words; i++) { + eerd = ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) + + E1000_EEPROM_RW_REG_START; + + E1000_WRITE_REG(hw, EERD, eerd); + error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_READ); + + if (error) { + break; + } + data[i] = (E1000_READ_REG(hw, EERD) >> E1000_EEPROM_RW_REG_DATA); + + } + + return error; +} + +/****************************************************************************** + * Writes a 16 bit word from the EEPROM using the EEWR register. + * + * hw - Struct containing variables accessed by shared code + * offset - offset of word in the EEPROM to read + * data - word read from the EEPROM + * words - number of words to read + *****************************************************************************/ +static int32_t +e1000_write_eeprom_eewr(struct e1000_hw *hw, + uint16_t offset, + uint16_t words, + uint16_t *data) +{ + uint32_t register_value = 0; + uint32_t i = 0; + int32_t error = 0; + + if (e1000_swfw_sync_acquire(hw, E1000_SWFW_EEP_SM)) + return -E1000_ERR_SWFW_SYNC; + + for (i = 0; i < words; i++) { + register_value = (data[i] << E1000_EEPROM_RW_REG_DATA) | + ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) | + E1000_EEPROM_RW_REG_START; + + error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_WRITE); + if (error) { + break; + } + + E1000_WRITE_REG(hw, EEWR, register_value); + + error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_WRITE); + + if (error) { + break; + } + } + + e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM); + return error; +} + +/****************************************************************************** + * Polls the status bit (bit 1) of the EERD to determine when the read is done. + * + * hw - Struct containing variables accessed by shared code + *****************************************************************************/ +static int32_t +e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd) +{ + uint32_t attempts = 100000; + uint32_t i, reg = 0; + int32_t done = E1000_ERR_EEPROM; + + for (i = 0; i < attempts; i++) { + if (eerd == E1000_EEPROM_POLL_READ) + reg = E1000_READ_REG(hw, EERD); + else + reg = E1000_READ_REG(hw, EEWR); + + if (reg & E1000_EEPROM_RW_REG_DONE) { + done = E1000_SUCCESS; + break; + } + udelay(5); + } + + return done; +} + +/*************************************************************************** +* Description: Determines if the onboard NVM is FLASH or EEPROM. +* +* hw - Struct containing variables accessed by shared code +****************************************************************************/ +static boolean_t +e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw) +{ + uint32_t eecd = 0; + + DEBUGFUNC("e1000_is_onboard_nvm_eeprom"); + + if (hw->mac_type == e1000_ich8lan) + return FALSE; + + if (hw->mac_type == e1000_82573) { + eecd = E1000_READ_REG(hw, EECD); + + /* Isolate bits 15 & 16 */ + eecd = ((eecd >> 15) & 0x03); + + /* If both bits are set, device is Flash type */ + if (eecd == 0x03) { + return FALSE; + } + } + return TRUE; +} + +/****************************************************************************** + * Verifies that the EEPROM has a valid checksum + * + * hw - Struct containing variables accessed by shared code + * + * Reads the first 64 16 bit words of the EEPROM and sums the values read. + * If the the sum of the 64 16 bit words is 0xBABA, the EEPROM's checksum is + * valid. + *****************************************************************************/ +int32_t +e1000_validate_eeprom_checksum(struct e1000_hw *hw) +{ + uint16_t checksum = 0; + uint16_t i, eeprom_data; + + DEBUGFUNC("e1000_validate_eeprom_checksum"); + + if ((hw->mac_type == e1000_82573) && + (e1000_is_onboard_nvm_eeprom(hw) == FALSE)) { + /* Check bit 4 of word 10h. If it is 0, firmware is done updating + * 10h-12h. Checksum may need to be fixed. */ + e1000_read_eeprom(hw, 0x10, 1, &eeprom_data); + if ((eeprom_data & 0x10) == 0) { + /* Read 0x23 and check bit 15. This bit is a 1 when the checksum + * has already been fixed. If the checksum is still wrong and this + * bit is a 1, we need to return bad checksum. Otherwise, we need + * to set this bit to a 1 and update the checksum. */ + e1000_read_eeprom(hw, 0x23, 1, &eeprom_data); + if ((eeprom_data & 0x8000) == 0) { + eeprom_data |= 0x8000; + e1000_write_eeprom(hw, 0x23, 1, &eeprom_data); + e1000_update_eeprom_checksum(hw); + } + } + } + + if (hw->mac_type == e1000_ich8lan) { + /* Drivers must allocate the shadow ram structure for the + * EEPROM checksum to be updated. Otherwise, this bit as well + * as the checksum must both be set correctly for this + * validation to pass. + */ + e1000_read_eeprom(hw, 0x19, 1, &eeprom_data); + if ((eeprom_data & 0x40) == 0) { + eeprom_data |= 0x40; + e1000_write_eeprom(hw, 0x19, 1, &eeprom_data); + e1000_update_eeprom_checksum(hw); + } + } + + for (i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) { + if (e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) { + DEBUGOUT("EEPROM Read Error\n"); + return -E1000_ERR_EEPROM; + } + checksum += eeprom_data; + } + + if (checksum == (uint16_t) EEPROM_SUM) + return E1000_SUCCESS; + else { + DEBUGOUT("EEPROM Checksum Invalid\n"); + return -E1000_ERR_EEPROM; + } +} + +/****************************************************************************** + * Calculates the EEPROM checksum and writes it to the EEPROM + * + * hw - Struct containing variables accessed by shared code + * + * Sums the first 63 16 bit words of the EEPROM. Subtracts the sum from 0xBABA. + * Writes the difference to word offset 63 of the EEPROM. + *****************************************************************************/ +int32_t +e1000_update_eeprom_checksum(struct e1000_hw *hw) +{ + uint32_t ctrl_ext; + uint16_t checksum = 0; + uint16_t i, eeprom_data; + + DEBUGFUNC("e1000_update_eeprom_checksum"); + + for (i = 0; i < EEPROM_CHECKSUM_REG; i++) { + if (e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) { + DEBUGOUT("EEPROM Read Error\n"); + return -E1000_ERR_EEPROM; + } + checksum += eeprom_data; + } + checksum = (uint16_t) EEPROM_SUM - checksum; + if (e1000_write_eeprom(hw, EEPROM_CHECKSUM_REG, 1, &checksum) < 0) { + DEBUGOUT("EEPROM Write Error\n"); + return -E1000_ERR_EEPROM; + } else if (hw->eeprom.type == e1000_eeprom_flash) { + e1000_commit_shadow_ram(hw); + } else if (hw->eeprom.type == e1000_eeprom_ich8) { + e1000_commit_shadow_ram(hw); + /* Reload the EEPROM, or else modifications will not appear + * until after next adapter reset. */ + ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); + ctrl_ext |= E1000_CTRL_EXT_EE_RST; + E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); + msleep(10); + } + return E1000_SUCCESS; +} + +/****************************************************************************** + * Parent function for writing words to the different EEPROM types. + * + * hw - Struct containing variables accessed by shared code + * offset - offset within the EEPROM to be written to + * words - number of words to write + * data - 16 bit word to be written to the EEPROM + * + * If e1000_update_eeprom_checksum is not called after this function, the + * EEPROM will most likely contain an invalid checksum. + *****************************************************************************/ +int32_t +e1000_write_eeprom(struct e1000_hw *hw, + uint16_t offset, + uint16_t words, + uint16_t *data) +{ + struct e1000_eeprom_info *eeprom = &hw->eeprom; + int32_t status = 0; + + DEBUGFUNC("e1000_write_eeprom"); + + /* If eeprom is not yet detected, do so now */ + if (eeprom->word_size == 0) + e1000_init_eeprom_params(hw); + + /* A check for invalid values: offset too large, too many words, and not + * enough words. + */ + if ((offset >= eeprom->word_size) || (words > eeprom->word_size - offset) || + (words == 0)) { + DEBUGOUT("\"words\" parameter out of bounds\n"); + return -E1000_ERR_EEPROM; + } + + /* 82573 writes only through eewr */ + if (eeprom->use_eewr == TRUE) + return e1000_write_eeprom_eewr(hw, offset, words, data); + + if (eeprom->type == e1000_eeprom_ich8) + return e1000_write_eeprom_ich8(hw, offset, words, data); + + /* Prepare the EEPROM for writing */ + if (e1000_acquire_eeprom(hw) != E1000_SUCCESS) + return -E1000_ERR_EEPROM; + + if (eeprom->type == e1000_eeprom_microwire) { + status = e1000_write_eeprom_microwire(hw, offset, words, data); + } else { + status = e1000_write_eeprom_spi(hw, offset, words, data); + msleep(10); + } + + /* Done with writing */ + e1000_release_eeprom(hw); + + return status; +} + +/****************************************************************************** + * Writes a 16 bit word to a given offset in an SPI EEPROM. + * + * hw - Struct containing variables accessed by shared code + * offset - offset within the EEPROM to be written to + * words - number of words to write + * data - pointer to array of 8 bit words to be written to the EEPROM + * + *****************************************************************************/ +static int32_t +e1000_write_eeprom_spi(struct e1000_hw *hw, + uint16_t offset, + uint16_t words, + uint16_t *data) +{ + struct e1000_eeprom_info *eeprom = &hw->eeprom; + uint16_t widx = 0; + + DEBUGFUNC("e1000_write_eeprom_spi"); + + while (widx < words) { + uint8_t write_opcode = EEPROM_WRITE_OPCODE_SPI; + + if (e1000_spi_eeprom_ready(hw)) return -E1000_ERR_EEPROM; + + e1000_standby_eeprom(hw); + + /* Send the WRITE ENABLE command (8 bit opcode ) */ + e1000_shift_out_ee_bits(hw, EEPROM_WREN_OPCODE_SPI, + eeprom->opcode_bits); + + e1000_standby_eeprom(hw); + + /* Some SPI eeproms use the 8th address bit embedded in the opcode */ + if ((eeprom->address_bits == 8) && (offset >= 128)) + write_opcode |= EEPROM_A8_OPCODE_SPI; + + /* Send the Write command (8-bit opcode + addr) */ + e1000_shift_out_ee_bits(hw, write_opcode, eeprom->opcode_bits); + + e1000_shift_out_ee_bits(hw, (uint16_t)((offset + widx)*2), + eeprom->address_bits); + + /* Send the data */ + + /* Loop to allow for up to whole page write (32 bytes) of eeprom */ + while (widx < words) { + uint16_t word_out = data[widx]; + word_out = (word_out >> 8) | (word_out << 8); + e1000_shift_out_ee_bits(hw, word_out, 16); + widx++; + + /* Some larger eeprom sizes are capable of a 32-byte PAGE WRITE + * operation, while the smaller eeproms are capable of an 8-byte + * PAGE WRITE operation. Break the inner loop to pass new address + */ + if ((((offset + widx)*2) % eeprom->page_size) == 0) { + e1000_standby_eeprom(hw); + break; + } + } + } + + return E1000_SUCCESS; +} + +/****************************************************************************** + * Writes a 16 bit word to a given offset in a Microwire EEPROM. + * + * hw - Struct containing variables accessed by shared code + * offset - offset within the EEPROM to be written to + * words - number of words to write + * data - pointer to array of 16 bit words to be written to the EEPROM + * + *****************************************************************************/ +static int32_t +e1000_write_eeprom_microwire(struct e1000_hw *hw, + uint16_t offset, + uint16_t words, + uint16_t *data) +{ + struct e1000_eeprom_info *eeprom = &hw->eeprom; + uint32_t eecd; + uint16_t words_written = 0; + uint16_t i = 0; + + DEBUGFUNC("e1000_write_eeprom_microwire"); + + /* Send the write enable command to the EEPROM (3-bit opcode plus + * 6/8-bit dummy address beginning with 11). It's less work to include + * the 11 of the dummy address as part of the opcode than it is to shift + * it over the correct number of bits for the address. This puts the + * EEPROM into write/erase mode. + */ + e1000_shift_out_ee_bits(hw, EEPROM_EWEN_OPCODE_MICROWIRE, + (uint16_t)(eeprom->opcode_bits + 2)); + + e1000_shift_out_ee_bits(hw, 0, (uint16_t)(eeprom->address_bits - 2)); + + /* Prepare the EEPROM */ + e1000_standby_eeprom(hw); + + while (words_written < words) { + /* Send the Write command (3-bit opcode + addr) */ + e1000_shift_out_ee_bits(hw, EEPROM_WRITE_OPCODE_MICROWIRE, + eeprom->opcode_bits); + + e1000_shift_out_ee_bits(hw, (uint16_t)(offset + words_written), + eeprom->address_bits); + + /* Send the data */ + e1000_shift_out_ee_bits(hw, data[words_written], 16); + + /* Toggle the CS line. This in effect tells the EEPROM to execute + * the previous command. + */ + e1000_standby_eeprom(hw); + + /* Read DO repeatedly until it is high (equal to '1'). The EEPROM will + * signal that the command has been completed by raising the DO signal. + * If DO does not go high in 10 milliseconds, then error out. + */ + for (i = 0; i < 200; i++) { + eecd = E1000_READ_REG(hw, EECD); + if (eecd & E1000_EECD_DO) break; + udelay(50); + } + if (i == 200) { + DEBUGOUT("EEPROM Write did not complete\n"); + return -E1000_ERR_EEPROM; + } + + /* Recover from write */ + e1000_standby_eeprom(hw); + + words_written++; + } + + /* Send the write disable command to the EEPROM (3-bit opcode plus + * 6/8-bit dummy address beginning with 10). It's less work to include + * the 10 of the dummy address as part of the opcode than it is to shift + * it over the correct number of bits for the address. This takes the + * EEPROM out of write/erase mode. + */ + e1000_shift_out_ee_bits(hw, EEPROM_EWDS_OPCODE_MICROWIRE, + (uint16_t)(eeprom->opcode_bits + 2)); + + e1000_shift_out_ee_bits(hw, 0, (uint16_t)(eeprom->address_bits - 2)); + + return E1000_SUCCESS; +} + +/****************************************************************************** + * Flushes the cached eeprom to NVM. This is done by saving the modified values + * in the eeprom cache and the non modified values in the currently active bank + * to the new bank. + * + * hw - Struct containing variables accessed by shared code + * offset - offset of word in the EEPROM to read + * data - word read from the EEPROM + * words - number of words to read + *****************************************************************************/ +static int32_t +e1000_commit_shadow_ram(struct e1000_hw *hw) +{ + uint32_t attempts = 100000; + uint32_t eecd = 0; + uint32_t flop = 0; + uint32_t i = 0; + int32_t error = E1000_SUCCESS; + uint32_t old_bank_offset = 0; + uint32_t new_bank_offset = 0; + uint8_t low_byte = 0; + uint8_t high_byte = 0; + boolean_t sector_write_failed = FALSE; + + if (hw->mac_type == e1000_82573) { + /* The flop register will be used to determine if flash type is STM */ + flop = E1000_READ_REG(hw, FLOP); + for (i=0; i < attempts; i++) { + eecd = E1000_READ_REG(hw, EECD); + if ((eecd & E1000_EECD_FLUPD) == 0) { + break; + } + udelay(5); + } + + if (i == attempts) { + return -E1000_ERR_EEPROM; + } + + /* If STM opcode located in bits 15:8 of flop, reset firmware */ + if ((flop & 0xFF00) == E1000_STM_OPCODE) { + E1000_WRITE_REG(hw, HICR, E1000_HICR_FW_RESET); + } + + /* Perform the flash update */ + E1000_WRITE_REG(hw, EECD, eecd | E1000_EECD_FLUPD); + + for (i=0; i < attempts; i++) { + eecd = E1000_READ_REG(hw, EECD); + if ((eecd & E1000_EECD_FLUPD) == 0) { + break; + } + udelay(5); + } + + if (i == attempts) { + return -E1000_ERR_EEPROM; + } + } + + if (hw->mac_type == e1000_ich8lan && hw->eeprom_shadow_ram != NULL) { + /* We're writing to the opposite bank so if we're on bank 1, + * write to bank 0 etc. We also need to erase the segment that + * is going to be written */ + if (!(E1000_READ_REG(hw, EECD) & E1000_EECD_SEC1VAL)) { + new_bank_offset = hw->flash_bank_size * 2; + old_bank_offset = 0; + e1000_erase_ich8_4k_segment(hw, 1); + } else { + old_bank_offset = hw->flash_bank_size * 2; + new_bank_offset = 0; + e1000_erase_ich8_4k_segment(hw, 0); + } + + sector_write_failed = FALSE; + /* Loop for every byte in the shadow RAM, + * which is in units of words. */ + for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) { + /* Determine whether to write the value stored + * in the other NVM bank or a modified value stored + * in the shadow RAM */ + if (hw->eeprom_shadow_ram[i].modified == TRUE) { + low_byte = (uint8_t)hw->eeprom_shadow_ram[i].eeprom_word; + udelay(100); + error = e1000_verify_write_ich8_byte(hw, + (i << 1) + new_bank_offset, low_byte); + + if (error != E1000_SUCCESS) + sector_write_failed = TRUE; + else { + high_byte = + (uint8_t)(hw->eeprom_shadow_ram[i].eeprom_word >> 8); + udelay(100); + } + } else { + e1000_read_ich8_byte(hw, (i << 1) + old_bank_offset, + &low_byte); + udelay(100); + error = e1000_verify_write_ich8_byte(hw, + (i << 1) + new_bank_offset, low_byte); + + if (error != E1000_SUCCESS) + sector_write_failed = TRUE; + else { + e1000_read_ich8_byte(hw, (i << 1) + old_bank_offset + 1, + &high_byte); + udelay(100); + } + } + + /* If the write of the low byte was successful, go ahread and + * write the high byte while checking to make sure that if it + * is the signature byte, then it is handled properly */ + if (sector_write_failed == FALSE) { + /* If the word is 0x13, then make sure the signature bits + * (15:14) are 11b until the commit has completed. + * This will allow us to write 10b which indicates the + * signature is valid. We want to do this after the write + * has completed so that we don't mark the segment valid + * while the write is still in progress */ + if (i == E1000_ICH_NVM_SIG_WORD) + high_byte = E1000_ICH_NVM_SIG_MASK | high_byte; + + error = e1000_verify_write_ich8_byte(hw, + (i << 1) + new_bank_offset + 1, high_byte); + if (error != E1000_SUCCESS) + sector_write_failed = TRUE; + + } else { + /* If the write failed then break from the loop and + * return an error */ + break; + } + } + + /* Don't bother writing the segment valid bits if sector + * programming failed. */ + if (sector_write_failed == FALSE) { + /* Finally validate the new segment by setting bit 15:14 + * to 10b in word 0x13 , this can be done without an + * erase as well since these bits are 11 to start with + * and we need to change bit 14 to 0b */ + e1000_read_ich8_byte(hw, + E1000_ICH_NVM_SIG_WORD * 2 + 1 + new_bank_offset, + &high_byte); + high_byte &= 0xBF; + error = e1000_verify_write_ich8_byte(hw, + E1000_ICH_NVM_SIG_WORD * 2 + 1 + new_bank_offset, high_byte); + /* And invalidate the previously valid segment by setting + * its signature word (0x13) high_byte to 0b. This can be + * done without an erase because flash erase sets all bits + * to 1's. We can write 1's to 0's without an erase */ + if (error == E1000_SUCCESS) { + error = e1000_verify_write_ich8_byte(hw, + E1000_ICH_NVM_SIG_WORD * 2 + 1 + old_bank_offset, 0); + } + + /* Clear the now not used entry in the cache */ + for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) { + hw->eeprom_shadow_ram[i].modified = FALSE; + hw->eeprom_shadow_ram[i].eeprom_word = 0xFFFF; + } + } + } + + return error; +} + +/****************************************************************************** + * Reads the adapter's MAC address from the EEPROM and inverts the LSB for the + * second function of dual function devices + * + * hw - Struct containing variables accessed by shared code + *****************************************************************************/ +int32_t +e1000_read_mac_addr(struct e1000_hw * hw) +{ + uint16_t offset; + uint16_t eeprom_data, i; + + DEBUGFUNC("e1000_read_mac_addr"); + + for (i = 0; i < NODE_ADDRESS_SIZE; i += 2) { + offset = i >> 1; + if (e1000_read_eeprom(hw, offset, 1, &eeprom_data) < 0) { + DEBUGOUT("EEPROM Read Error\n"); + return -E1000_ERR_EEPROM; + } + hw->perm_mac_addr[i] = (uint8_t) (eeprom_data & 0x00FF); + hw->perm_mac_addr[i+1] = (uint8_t) (eeprom_data >> 8); + } + + switch (hw->mac_type) { + default: + break; + case e1000_82546: + case e1000_82546_rev_3: + case e1000_82571: + case e1000_80003es2lan: + if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1) + hw->perm_mac_addr[5] ^= 0x01; + break; + } + + for (i = 0; i < NODE_ADDRESS_SIZE; i++) + hw->mac_addr[i] = hw->perm_mac_addr[i]; + return E1000_SUCCESS; +} + +/****************************************************************************** + * Initializes receive address filters. + * + * hw - Struct containing variables accessed by shared code + * + * Places the MAC address in receive address register 0 and clears the rest + * of the receive addresss registers. Clears the multicast table. Assumes + * the receiver is in reset when the routine is called. + *****************************************************************************/ +static void +e1000_init_rx_addrs(struct e1000_hw *hw) +{ + uint32_t i; + uint32_t rar_num; + + DEBUGFUNC("e1000_init_rx_addrs"); + + /* Setup the receive address. */ + DEBUGOUT("Programming MAC Address into RAR[0]\n"); + + e1000_rar_set(hw, hw->mac_addr, 0); + + rar_num = E1000_RAR_ENTRIES; + + /* Reserve a spot for the Locally Administered Address to work around + * an 82571 issue in which a reset on one port will reload the MAC on + * the other port. */ + if ((hw->mac_type == e1000_82571) && (hw->laa_is_present == TRUE)) + rar_num -= 1; + if (hw->mac_type == e1000_ich8lan) + rar_num = E1000_RAR_ENTRIES_ICH8LAN; + + /* Zero out the other 15 receive addresses. */ + DEBUGOUT("Clearing RAR[1-15]\n"); + for (i = 1; i < rar_num; i++) { + E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0); + E1000_WRITE_FLUSH(hw); + E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0); + E1000_WRITE_FLUSH(hw); + } +} + +/****************************************************************************** + * Hashes an address to determine its location in the multicast table + * + * hw - Struct containing variables accessed by shared code + * mc_addr - the multicast address to hash + *****************************************************************************/ +uint32_t +e1000_hash_mc_addr(struct e1000_hw *hw, + uint8_t *mc_addr) +{ + uint32_t hash_value = 0; + + /* The portion of the address that is used for the hash table is + * determined by the mc_filter_type setting. + */ + switch (hw->mc_filter_type) { + /* [0] [1] [2] [3] [4] [5] + * 01 AA 00 12 34 56 + * LSB MSB + */ + case 0: + if (hw->mac_type == e1000_ich8lan) { + /* [47:38] i.e. 0x158 for above example address */ + hash_value = ((mc_addr[4] >> 6) | (((uint16_t) mc_addr[5]) << 2)); + } else { + /* [47:36] i.e. 0x563 for above example address */ + hash_value = ((mc_addr[4] >> 4) | (((uint16_t) mc_addr[5]) << 4)); + } + break; + case 1: + if (hw->mac_type == e1000_ich8lan) { + /* [46:37] i.e. 0x2B1 for above example address */ + hash_value = ((mc_addr[4] >> 5) | (((uint16_t) mc_addr[5]) << 3)); + } else { + /* [46:35] i.e. 0xAC6 for above example address */ + hash_value = ((mc_addr[4] >> 3) | (((uint16_t) mc_addr[5]) << 5)); + } + break; + case 2: + if (hw->mac_type == e1000_ich8lan) { + /*[45:36] i.e. 0x163 for above example address */ + hash_value = ((mc_addr[4] >> 4) | (((uint16_t) mc_addr[5]) << 4)); + } else { + /* [45:34] i.e. 0x5D8 for above example address */ + hash_value = ((mc_addr[4] >> 2) | (((uint16_t) mc_addr[5]) << 6)); + } + break; + case 3: + if (hw->mac_type == e1000_ich8lan) { + /* [43:34] i.e. 0x18D for above example address */ + hash_value = ((mc_addr[4] >> 2) | (((uint16_t) mc_addr[5]) << 6)); + } else { + /* [43:32] i.e. 0x634 for above example address */ + hash_value = ((mc_addr[4]) | (((uint16_t) mc_addr[5]) << 8)); + } + break; + } + + hash_value &= 0xFFF; + if (hw->mac_type == e1000_ich8lan) + hash_value &= 0x3FF; + + return hash_value; +} + +/****************************************************************************** + * Sets the bit in the multicast table corresponding to the hash value. + * + * hw - Struct containing variables accessed by shared code + * hash_value - Multicast address hash value + *****************************************************************************/ +void +e1000_mta_set(struct e1000_hw *hw, + uint32_t hash_value) +{ + uint32_t hash_bit, hash_reg; + uint32_t mta; + uint32_t temp; + + /* The MTA is a register array of 128 32-bit registers. + * It is treated like an array of 4096 bits. We want to set + * bit BitArray[hash_value]. So we figure out what register + * the bit is in, read it, OR in the new bit, then write + * back the new value. The register is determined by the + * upper 7 bits of the hash value and the bit within that + * register are determined by the lower 5 bits of the value. + */ + hash_reg = (hash_value >> 5) & 0x7F; + if (hw->mac_type == e1000_ich8lan) + hash_reg &= 0x1F; + + hash_bit = hash_value & 0x1F; + + mta = E1000_READ_REG_ARRAY(hw, MTA, hash_reg); + + mta |= (1 << hash_bit); + + /* If we are on an 82544 and we are trying to write an odd offset + * in the MTA, save off the previous entry before writing and + * restore the old value after writing. + */ + if ((hw->mac_type == e1000_82544) && ((hash_reg & 0x1) == 1)) { + temp = E1000_READ_REG_ARRAY(hw, MTA, (hash_reg - 1)); + E1000_WRITE_REG_ARRAY(hw, MTA, hash_reg, mta); + E1000_WRITE_FLUSH(hw); + E1000_WRITE_REG_ARRAY(hw, MTA, (hash_reg - 1), temp); + E1000_WRITE_FLUSH(hw); + } else { + E1000_WRITE_REG_ARRAY(hw, MTA, hash_reg, mta); + E1000_WRITE_FLUSH(hw); + } +} + +/****************************************************************************** + * Puts an ethernet address into a receive address register. + * + * hw - Struct containing variables accessed by shared code + * addr - Address to put into receive address register + * index - Receive address register to write + *****************************************************************************/ +void +e1000_rar_set(struct e1000_hw *hw, + uint8_t *addr, + uint32_t index) +{ + uint32_t rar_low, rar_high; + + /* HW expects these in little endian so we reverse the byte order + * from network order (big endian) to little endian + */ + rar_low = ((uint32_t) addr[0] | + ((uint32_t) addr[1] << 8) | + ((uint32_t) addr[2] << 16) | ((uint32_t) addr[3] << 24)); + rar_high = ((uint32_t) addr[4] | ((uint32_t) addr[5] << 8)); + + /* Disable Rx and flush all Rx frames before enabling RSS to avoid Rx + * unit hang. + * + * Description: + * If there are any Rx frames queued up or otherwise present in the HW + * before RSS is enabled, and then we enable RSS, the HW Rx unit will + * hang. To work around this issue, we have to disable receives and + * flush out all Rx frames before we enable RSS. To do so, we modify we + * redirect all Rx traffic to manageability and then reset the HW. + * This flushes away Rx frames, and (since the redirections to + * manageability persists across resets) keeps new ones from coming in + * while we work. Then, we clear the Address Valid AV bit for all MAC + * addresses and undo the re-direction to manageability. + * Now, frames are coming in again, but the MAC won't accept them, so + * far so good. We now proceed to initialize RSS (if necessary) and + * configure the Rx unit. Last, we re-enable the AV bits and continue + * on our merry way. + */ + switch (hw->mac_type) { + case e1000_82571: + case e1000_82572: + case e1000_80003es2lan: + if (hw->leave_av_bit_off == TRUE) + break; + default: + /* Indicate to hardware the Address is Valid. */ + rar_high |= E1000_RAH_AV; + break; + } + + E1000_WRITE_REG_ARRAY(hw, RA, (index << 1), rar_low); + E1000_WRITE_FLUSH(hw); + E1000_WRITE_REG_ARRAY(hw, RA, ((index << 1) + 1), rar_high); + E1000_WRITE_FLUSH(hw); +} + +/****************************************************************************** + * Writes a value to the specified offset in the VLAN filter table. + * + * hw - Struct containing variables accessed by shared code + * offset - Offset in VLAN filer table to write + * value - Value to write into VLAN filter table + *****************************************************************************/ +void +e1000_write_vfta(struct e1000_hw *hw, + uint32_t offset, + uint32_t value) +{ + uint32_t temp; + + if (hw->mac_type == e1000_ich8lan) + return; + + if ((hw->mac_type == e1000_82544) && ((offset & 0x1) == 1)) { + temp = E1000_READ_REG_ARRAY(hw, VFTA, (offset - 1)); + E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value); + E1000_WRITE_FLUSH(hw); + E1000_WRITE_REG_ARRAY(hw, VFTA, (offset - 1), temp); + E1000_WRITE_FLUSH(hw); + } else { + E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value); + E1000_WRITE_FLUSH(hw); + } +} + +/****************************************************************************** + * Clears the VLAN filer table + * + * hw - Struct containing variables accessed by shared code + *****************************************************************************/ +static void +e1000_clear_vfta(struct e1000_hw *hw) +{ + uint32_t offset; + uint32_t vfta_value = 0; + uint32_t vfta_offset = 0; + uint32_t vfta_bit_in_reg = 0; + + if (hw->mac_type == e1000_ich8lan) + return; + + if (hw->mac_type == e1000_82573) { + if (hw->mng_cookie.vlan_id != 0) { + /* The VFTA is a 4096b bit-field, each identifying a single VLAN + * ID. The following operations determine which 32b entry + * (i.e. offset) into the array we want to set the VLAN ID + * (i.e. bit) of the manageability unit. */ + vfta_offset = (hw->mng_cookie.vlan_id >> + E1000_VFTA_ENTRY_SHIFT) & + E1000_VFTA_ENTRY_MASK; + vfta_bit_in_reg = 1 << (hw->mng_cookie.vlan_id & + E1000_VFTA_ENTRY_BIT_SHIFT_MASK); + } + } + for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) { + /* If the offset we want to clear is the same offset of the + * manageability VLAN ID, then clear all bits except that of the + * manageability unit */ + vfta_value = (offset == vfta_offset) ? vfta_bit_in_reg : 0; + E1000_WRITE_REG_ARRAY(hw, VFTA, offset, vfta_value); + E1000_WRITE_FLUSH(hw); + } +} + +static int32_t +e1000_id_led_init(struct e1000_hw * hw) +{ + uint32_t ledctl; + const uint32_t ledctl_mask = 0x000000FF; + const uint32_t ledctl_on = E1000_LEDCTL_MODE_LED_ON; + const uint32_t ledctl_off = E1000_LEDCTL_MODE_LED_OFF; + uint16_t eeprom_data, i, temp; + const uint16_t led_mask = 0x0F; + + DEBUGFUNC("e1000_id_led_init"); + + if (hw->mac_type < e1000_82540) { + /* Nothing to do */ + return E1000_SUCCESS; + } + + ledctl = E1000_READ_REG(hw, LEDCTL); + hw->ledctl_default = ledctl; + hw->ledctl_mode1 = hw->ledctl_default; + hw->ledctl_mode2 = hw->ledctl_default; + + if (e1000_read_eeprom(hw, EEPROM_ID_LED_SETTINGS, 1, &eeprom_data) < 0) { + DEBUGOUT("EEPROM Read Error\n"); + return -E1000_ERR_EEPROM; + } + + if ((hw->mac_type == e1000_82573) && + (eeprom_data == ID_LED_RESERVED_82573)) + eeprom_data = ID_LED_DEFAULT_82573; + else if ((eeprom_data == ID_LED_RESERVED_0000) || + (eeprom_data == ID_LED_RESERVED_FFFF)) { + if (hw->mac_type == e1000_ich8lan) + eeprom_data = ID_LED_DEFAULT_ICH8LAN; + else + eeprom_data = ID_LED_DEFAULT; + } + + for (i = 0; i < 4; i++) { + temp = (eeprom_data >> (i << 2)) & led_mask; + switch (temp) { + case ID_LED_ON1_DEF2: + case ID_LED_ON1_ON2: + case ID_LED_ON1_OFF2: + hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3)); + hw->ledctl_mode1 |= ledctl_on << (i << 3); + break; + case ID_LED_OFF1_DEF2: + case ID_LED_OFF1_ON2: + case ID_LED_OFF1_OFF2: + hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3)); + hw->ledctl_mode1 |= ledctl_off << (i << 3); + break; + default: + /* Do nothing */ + break; + } + switch (temp) { + case ID_LED_DEF1_ON2: + case ID_LED_ON1_ON2: + case ID_LED_OFF1_ON2: + hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3)); + hw->ledctl_mode2 |= ledctl_on << (i << 3); + break; + case ID_LED_DEF1_OFF2: + case ID_LED_ON1_OFF2: + case ID_LED_OFF1_OFF2: + hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3)); + hw->ledctl_mode2 |= ledctl_off << (i << 3); + break; + default: + /* Do nothing */ + break; + } + } + return E1000_SUCCESS; +} + +/****************************************************************************** + * Prepares SW controlable LED for use and saves the current state of the LED. + * + * hw - Struct containing variables accessed by shared code + *****************************************************************************/ +int32_t +e1000_setup_led(struct e1000_hw *hw) +{ + uint32_t ledctl; + int32_t ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_setup_led"); + + switch (hw->mac_type) { + case e1000_82542_rev2_0: + case e1000_82542_rev2_1: + case e1000_82543: + case e1000_82544: + /* No setup necessary */ + break; + case e1000_82541: + case e1000_82547: + case e1000_82541_rev_2: + case e1000_82547_rev_2: + /* Turn off PHY Smart Power Down (if enabled) */ + ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO, + &hw->phy_spd_default); + if (ret_val) + return ret_val; + ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, + (uint16_t)(hw->phy_spd_default & + ~IGP01E1000_GMII_SPD)); + if (ret_val) + return ret_val; + /* Fall Through */ + default: + if (hw->media_type == e1000_media_type_fiber) { + ledctl = E1000_READ_REG(hw, LEDCTL); + /* Save current LEDCTL settings */ + hw->ledctl_default = ledctl; + /* Turn off LED0 */ + ledctl &= ~(E1000_LEDCTL_LED0_IVRT | + E1000_LEDCTL_LED0_BLINK | + E1000_LEDCTL_LED0_MODE_MASK); + ledctl |= (E1000_LEDCTL_MODE_LED_OFF << + E1000_LEDCTL_LED0_MODE_SHIFT); + E1000_WRITE_REG(hw, LEDCTL, ledctl); + } else if (hw->media_type == e1000_media_type_copper) + E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode1); + break; + } + + return E1000_SUCCESS; +} + + +/****************************************************************************** + * Used on 82571 and later Si that has LED blink bits. + * Callers must use their own timer and should have already called + * e1000_id_led_init() + * Call e1000_cleanup led() to stop blinking + * + * hw - Struct containing variables accessed by shared code + *****************************************************************************/ +int32_t +e1000_blink_led_start(struct e1000_hw *hw) +{ + int16_t i; + uint32_t ledctl_blink = 0; + + DEBUGFUNC("e1000_id_led_blink_on"); + + if (hw->mac_type < e1000_82571) { + /* Nothing to do */ + return E1000_SUCCESS; + } + if (hw->media_type == e1000_media_type_fiber) { + /* always blink LED0 for PCI-E fiber */ + ledctl_blink = E1000_LEDCTL_LED0_BLINK | + (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED0_MODE_SHIFT); + } else { + /* set the blink bit for each LED that's "on" (0x0E) in ledctl_mode2 */ + ledctl_blink = hw->ledctl_mode2; + for (i=0; i < 4; i++) + if (((hw->ledctl_mode2 >> (i * 8)) & 0xFF) == + E1000_LEDCTL_MODE_LED_ON) + ledctl_blink |= (E1000_LEDCTL_LED0_BLINK << (i * 8)); + } + + E1000_WRITE_REG(hw, LEDCTL, ledctl_blink); + + return E1000_SUCCESS; +} + +/****************************************************************************** + * Restores the saved state of the SW controlable LED. + * + * hw - Struct containing variables accessed by shared code + *****************************************************************************/ +int32_t +e1000_cleanup_led(struct e1000_hw *hw) +{ + int32_t ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_cleanup_led"); + + switch (hw->mac_type) { + case e1000_82542_rev2_0: + case e1000_82542_rev2_1: + case e1000_82543: + case e1000_82544: + /* No cleanup necessary */ + break; + case e1000_82541: + case e1000_82547: + case e1000_82541_rev_2: + case e1000_82547_rev_2: + /* Turn on PHY Smart Power Down (if previously enabled) */ + ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, + hw->phy_spd_default); + if (ret_val) + return ret_val; + /* Fall Through */ + default: + if (hw->phy_type == e1000_phy_ife) { + e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED, 0); + break; + } + /* Restore LEDCTL settings */ + E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_default); + break; + } + + return E1000_SUCCESS; +} + +/****************************************************************************** + * Turns on the software controllable LED + * + * hw - Struct containing variables accessed by shared code + *****************************************************************************/ +int32_t +e1000_led_on(struct e1000_hw *hw) +{ + uint32_t ctrl = E1000_READ_REG(hw, CTRL); + + DEBUGFUNC("e1000_led_on"); + + switch (hw->mac_type) { + case e1000_82542_rev2_0: + case e1000_82542_rev2_1: + case e1000_82543: + /* Set SW Defineable Pin 0 to turn on the LED */ + ctrl |= E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + break; + case e1000_82544: + if (hw->media_type == e1000_media_type_fiber) { + /* Set SW Defineable Pin 0 to turn on the LED */ + ctrl |= E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + } else { + /* Clear SW Defineable Pin 0 to turn on the LED */ + ctrl &= ~E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + } + break; + default: + if (hw->media_type == e1000_media_type_fiber) { + /* Clear SW Defineable Pin 0 to turn on the LED */ + ctrl &= ~E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + } else if (hw->phy_type == e1000_phy_ife) { + e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED, + (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_ON)); + } else if (hw->media_type == e1000_media_type_copper) { + E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode2); + return E1000_SUCCESS; + } + break; + } + + E1000_WRITE_REG(hw, CTRL, ctrl); + + return E1000_SUCCESS; +} + +/****************************************************************************** + * Turns off the software controllable LED + * + * hw - Struct containing variables accessed by shared code + *****************************************************************************/ +int32_t +e1000_led_off(struct e1000_hw *hw) +{ + uint32_t ctrl = E1000_READ_REG(hw, CTRL); + + DEBUGFUNC("e1000_led_off"); + + switch (hw->mac_type) { + case e1000_82542_rev2_0: + case e1000_82542_rev2_1: + case e1000_82543: + /* Clear SW Defineable Pin 0 to turn off the LED */ + ctrl &= ~E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + break; + case e1000_82544: + if (hw->media_type == e1000_media_type_fiber) { + /* Clear SW Defineable Pin 0 to turn off the LED */ + ctrl &= ~E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + } else { + /* Set SW Defineable Pin 0 to turn off the LED */ + ctrl |= E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + } + break; + default: + if (hw->media_type == e1000_media_type_fiber) { + /* Set SW Defineable Pin 0 to turn off the LED */ + ctrl |= E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + } else if (hw->phy_type == e1000_phy_ife) { + e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED, + (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_OFF)); + } else if (hw->media_type == e1000_media_type_copper) { + E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode1); + return E1000_SUCCESS; + } + break; + } + + E1000_WRITE_REG(hw, CTRL, ctrl); + + return E1000_SUCCESS; +} + +/****************************************************************************** + * Clears all hardware statistics counters. + * + * hw - Struct containing variables accessed by shared code + *****************************************************************************/ +static void +e1000_clear_hw_cntrs(struct e1000_hw *hw) +{ + volatile uint32_t temp; + + temp = E1000_READ_REG(hw, CRCERRS); + temp = E1000_READ_REG(hw, SYMERRS); + temp = E1000_READ_REG(hw, MPC); + temp = E1000_READ_REG(hw, SCC); + temp = E1000_READ_REG(hw, ECOL); + temp = E1000_READ_REG(hw, MCC); + temp = E1000_READ_REG(hw, LATECOL); + temp = E1000_READ_REG(hw, COLC); + temp = E1000_READ_REG(hw, DC); + temp = E1000_READ_REG(hw, SEC); + temp = E1000_READ_REG(hw, RLEC); + temp = E1000_READ_REG(hw, XONRXC); + temp = E1000_READ_REG(hw, XONTXC); + temp = E1000_READ_REG(hw, XOFFRXC); + temp = E1000_READ_REG(hw, XOFFTXC); + temp = E1000_READ_REG(hw, FCRUC); + + if (hw->mac_type != e1000_ich8lan) { + temp = E1000_READ_REG(hw, PRC64); + temp = E1000_READ_REG(hw, PRC127); + temp = E1000_READ_REG(hw, PRC255); + temp = E1000_READ_REG(hw, PRC511); + temp = E1000_READ_REG(hw, PRC1023); + temp = E1000_READ_REG(hw, PRC1522); + } + + temp = E1000_READ_REG(hw, GPRC); + temp = E1000_READ_REG(hw, BPRC); + temp = E1000_READ_REG(hw, MPRC); + temp = E1000_READ_REG(hw, GPTC); + temp = E1000_READ_REG(hw, GORCL); + temp = E1000_READ_REG(hw, GORCH); + temp = E1000_READ_REG(hw, GOTCL); + temp = E1000_READ_REG(hw, GOTCH); + temp = E1000_READ_REG(hw, RNBC); + temp = E1000_READ_REG(hw, RUC); + temp = E1000_READ_REG(hw, RFC); + temp = E1000_READ_REG(hw, ROC); + temp = E1000_READ_REG(hw, RJC); + temp = E1000_READ_REG(hw, TORL); + temp = E1000_READ_REG(hw, TORH); + temp = E1000_READ_REG(hw, TOTL); + temp = E1000_READ_REG(hw, TOTH); + temp = E1000_READ_REG(hw, TPR); + temp = E1000_READ_REG(hw, TPT); + + if (hw->mac_type != e1000_ich8lan) { + temp = E1000_READ_REG(hw, PTC64); + temp = E1000_READ_REG(hw, PTC127); + temp = E1000_READ_REG(hw, PTC255); + temp = E1000_READ_REG(hw, PTC511); + temp = E1000_READ_REG(hw, PTC1023); + temp = E1000_READ_REG(hw, PTC1522); + } + + temp = E1000_READ_REG(hw, MPTC); + temp = E1000_READ_REG(hw, BPTC); + + if (hw->mac_type < e1000_82543) return; + + temp = E1000_READ_REG(hw, ALGNERRC); + temp = E1000_READ_REG(hw, RXERRC); + temp = E1000_READ_REG(hw, TNCRS); + temp = E1000_READ_REG(hw, CEXTERR); + temp = E1000_READ_REG(hw, TSCTC); + temp = E1000_READ_REG(hw, TSCTFC); + + if (hw->mac_type <= e1000_82544) return; + + temp = E1000_READ_REG(hw, MGTPRC); + temp = E1000_READ_REG(hw, MGTPDC); + temp = E1000_READ_REG(hw, MGTPTC); + + if (hw->mac_type <= e1000_82547_rev_2) return; + + temp = E1000_READ_REG(hw, IAC); + temp = E1000_READ_REG(hw, ICRXOC); + + if (hw->mac_type == e1000_ich8lan) return; + + temp = E1000_READ_REG(hw, ICRXPTC); + temp = E1000_READ_REG(hw, ICRXATC); + temp = E1000_READ_REG(hw, ICTXPTC); + temp = E1000_READ_REG(hw, ICTXATC); + temp = E1000_READ_REG(hw, ICTXQEC); + temp = E1000_READ_REG(hw, ICTXQMTC); + temp = E1000_READ_REG(hw, ICRXDMTC); +} + +/****************************************************************************** + * Resets Adaptive IFS to its default state. + * + * hw - Struct containing variables accessed by shared code + * + * Call this after e1000_init_hw. You may override the IFS defaults by setting + * hw->ifs_params_forced to TRUE. However, you must initialize hw-> + * current_ifs_val, ifs_min_val, ifs_max_val, ifs_step_size, and ifs_ratio + * before calling this function. + *****************************************************************************/ +void +e1000_reset_adaptive(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_reset_adaptive"); + + if (hw->adaptive_ifs) { + if (!hw->ifs_params_forced) { + hw->current_ifs_val = 0; + hw->ifs_min_val = IFS_MIN; + hw->ifs_max_val = IFS_MAX; + hw->ifs_step_size = IFS_STEP; + hw->ifs_ratio = IFS_RATIO; + } + hw->in_ifs_mode = FALSE; + E1000_WRITE_REG(hw, AIT, 0); + } else { + DEBUGOUT("Not in Adaptive IFS mode!\n"); + } +} + +/****************************************************************************** + * Called during the callback/watchdog routine to update IFS value based on + * the ratio of transmits to collisions. + * + * hw - Struct containing variables accessed by shared code + * tx_packets - Number of transmits since last callback + * total_collisions - Number of collisions since last callback + *****************************************************************************/ +void +e1000_update_adaptive(struct e1000_hw *hw) +{ + DEBUGFUNC("e1000_update_adaptive"); + + if (hw->adaptive_ifs) { + if ((hw->collision_delta * hw->ifs_ratio) > hw->tx_packet_delta) { + if (hw->tx_packet_delta > MIN_NUM_XMITS) { + hw->in_ifs_mode = TRUE; + if (hw->current_ifs_val < hw->ifs_max_val) { + if (hw->current_ifs_val == 0) + hw->current_ifs_val = hw->ifs_min_val; + else + hw->current_ifs_val += hw->ifs_step_size; + E1000_WRITE_REG(hw, AIT, hw->current_ifs_val); + } + } + } else { + if (hw->in_ifs_mode && (hw->tx_packet_delta <= MIN_NUM_XMITS)) { + hw->current_ifs_val = 0; + hw->in_ifs_mode = FALSE; + E1000_WRITE_REG(hw, AIT, 0); + } + } + } else { + DEBUGOUT("Not in Adaptive IFS mode!\n"); + } +} + +/****************************************************************************** + * Adjusts the statistic counters when a frame is accepted by TBI_ACCEPT + * + * hw - Struct containing variables accessed by shared code + * frame_len - The length of the frame in question + * mac_addr - The Ethernet destination address of the frame in question + *****************************************************************************/ +void +e1000_tbi_adjust_stats(struct e1000_hw *hw, + struct e1000_hw_stats *stats, + uint32_t frame_len, + uint8_t *mac_addr) +{ + uint64_t carry_bit; + + /* First adjust the frame length. */ + frame_len--; + /* We need to adjust the statistics counters, since the hardware + * counters overcount this packet as a CRC error and undercount + * the packet as a good packet + */ + /* This packet should not be counted as a CRC error. */ + stats->crcerrs--; + /* This packet does count as a Good Packet Received. */ + stats->gprc++; + + /* Adjust the Good Octets received counters */ + carry_bit = 0x80000000 & stats->gorcl; + stats->gorcl += frame_len; + /* If the high bit of Gorcl (the low 32 bits of the Good Octets + * Received Count) was one before the addition, + * AND it is zero after, then we lost the carry out, + * need to add one to Gorch (Good Octets Received Count High). + * This could be simplified if all environments supported + * 64-bit integers. + */ + if (carry_bit && ((stats->gorcl & 0x80000000) == 0)) + stats->gorch++; + /* Is this a broadcast or multicast? Check broadcast first, + * since the test for a multicast frame will test positive on + * a broadcast frame. + */ + if ((mac_addr[0] == (uint8_t) 0xff) && (mac_addr[1] == (uint8_t) 0xff)) + /* Broadcast packet */ + stats->bprc++; + else if (*mac_addr & 0x01) + /* Multicast packet */ + stats->mprc++; + + if (frame_len == hw->max_frame_size) { + /* In this case, the hardware has overcounted the number of + * oversize frames. + */ + if (stats->roc > 0) + stats->roc--; + } + + /* Adjust the bin counters when the extra byte put the frame in the + * wrong bin. Remember that the frame_len was adjusted above. + */ + if (frame_len == 64) { + stats->prc64++; + stats->prc127--; + } else if (frame_len == 127) { + stats->prc127++; + stats->prc255--; + } else if (frame_len == 255) { + stats->prc255++; + stats->prc511--; + } else if (frame_len == 511) { + stats->prc511++; + stats->prc1023--; + } else if (frame_len == 1023) { + stats->prc1023++; + stats->prc1522--; + } else if (frame_len == 1522) { + stats->prc1522++; + } +} + +/****************************************************************************** + * Gets the current PCI bus type, speed, and width of the hardware + * + * hw - Struct containing variables accessed by shared code + *****************************************************************************/ +void +e1000_get_bus_info(struct e1000_hw *hw) +{ + int32_t ret_val; + uint16_t pci_ex_link_status; + uint32_t status; + + switch (hw->mac_type) { + case e1000_82542_rev2_0: + case e1000_82542_rev2_1: + hw->bus_type = e1000_bus_type_pci; + hw->bus_speed = e1000_bus_speed_unknown; + hw->bus_width = e1000_bus_width_unknown; + break; + case e1000_82571: + case e1000_82572: + case e1000_82573: + case e1000_80003es2lan: + hw->bus_type = e1000_bus_type_pci_express; + hw->bus_speed = e1000_bus_speed_2500; + ret_val = e1000_read_pcie_cap_reg(hw, + PCI_EX_LINK_STATUS, + &pci_ex_link_status); + if (ret_val) + hw->bus_width = e1000_bus_width_unknown; + else + hw->bus_width = (pci_ex_link_status & PCI_EX_LINK_WIDTH_MASK) >> + PCI_EX_LINK_WIDTH_SHIFT; + break; + case e1000_ich8lan: + hw->bus_type = e1000_bus_type_pci_express; + hw->bus_speed = e1000_bus_speed_2500; + hw->bus_width = e1000_bus_width_pciex_1; + break; + default: + status = E1000_READ_REG(hw, STATUS); + hw->bus_type = (status & E1000_STATUS_PCIX_MODE) ? + e1000_bus_type_pcix : e1000_bus_type_pci; + + if (hw->device_id == E1000_DEV_ID_82546EB_QUAD_COPPER) { + hw->bus_speed = (hw->bus_type == e1000_bus_type_pci) ? + e1000_bus_speed_66 : e1000_bus_speed_120; + } else if (hw->bus_type == e1000_bus_type_pci) { + hw->bus_speed = (status & E1000_STATUS_PCI66) ? + e1000_bus_speed_66 : e1000_bus_speed_33; + } else { + switch (status & E1000_STATUS_PCIX_SPEED) { + case E1000_STATUS_PCIX_SPEED_66: + hw->bus_speed = e1000_bus_speed_66; + break; + case E1000_STATUS_PCIX_SPEED_100: + hw->bus_speed = e1000_bus_speed_100; + break; + case E1000_STATUS_PCIX_SPEED_133: + hw->bus_speed = e1000_bus_speed_133; + break; + default: + hw->bus_speed = e1000_bus_speed_reserved; + break; + } + } + hw->bus_width = (status & E1000_STATUS_BUS64) ? + e1000_bus_width_64 : e1000_bus_width_32; + break; + } +} + +/****************************************************************************** + * Writes a value to one of the devices registers using port I/O (as opposed to + * memory mapped I/O). Only 82544 and newer devices support port I/O. + * + * hw - Struct containing variables accessed by shared code + * offset - offset to write to + * value - value to write + *****************************************************************************/ +static void +e1000_write_reg_io(struct e1000_hw *hw, + uint32_t offset, + uint32_t value) +{ + unsigned long io_addr = hw->io_base; + unsigned long io_data = hw->io_base + 4; + + e1000_io_write(hw, io_addr, offset); + e1000_io_write(hw, io_data, value); +} + +/****************************************************************************** + * Estimates the cable length. + * + * hw - Struct containing variables accessed by shared code + * min_length - The estimated minimum length + * max_length - The estimated maximum length + * + * returns: - E1000_ERR_XXX + * E1000_SUCCESS + * + * This function always returns a ranged length (minimum & maximum). + * So for M88 phy's, this function interprets the one value returned from the + * register to the minimum and maximum range. + * For IGP phy's, the function calculates the range by the AGC registers. + *****************************************************************************/ +static int32_t +e1000_get_cable_length(struct e1000_hw *hw, + uint16_t *min_length, + uint16_t *max_length) +{ + int32_t ret_val; + uint16_t agc_value = 0; + uint16_t i, phy_data; + uint16_t cable_length; + + DEBUGFUNC("e1000_get_cable_length"); + + *min_length = *max_length = 0; + + /* Use old method for Phy older than IGP */ + if (hw->phy_type == e1000_phy_m88) { + + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, + &phy_data); + if (ret_val) + return ret_val; + cable_length = (phy_data & M88E1000_PSSR_CABLE_LENGTH) >> + M88E1000_PSSR_CABLE_LENGTH_SHIFT; + + /* Convert the enum value to ranged values */ + switch (cable_length) { + case e1000_cable_length_50: + *min_length = 0; + *max_length = e1000_igp_cable_length_50; + break; + case e1000_cable_length_50_80: + *min_length = e1000_igp_cable_length_50; + *max_length = e1000_igp_cable_length_80; + break; + case e1000_cable_length_80_110: + *min_length = e1000_igp_cable_length_80; + *max_length = e1000_igp_cable_length_110; + break; + case e1000_cable_length_110_140: + *min_length = e1000_igp_cable_length_110; + *max_length = e1000_igp_cable_length_140; + break; + case e1000_cable_length_140: + *min_length = e1000_igp_cable_length_140; + *max_length = e1000_igp_cable_length_170; + break; + default: + return -E1000_ERR_PHY; + break; + } + } else if (hw->phy_type == e1000_phy_gg82563) { + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_DSP_DISTANCE, + &phy_data); + if (ret_val) + return ret_val; + cable_length = phy_data & GG82563_DSPD_CABLE_LENGTH; + + switch (cable_length) { + case e1000_gg_cable_length_60: + *min_length = 0; + *max_length = e1000_igp_cable_length_60; + break; + case e1000_gg_cable_length_60_115: + *min_length = e1000_igp_cable_length_60; + *max_length = e1000_igp_cable_length_115; + break; + case e1000_gg_cable_length_115_150: + *min_length = e1000_igp_cable_length_115; + *max_length = e1000_igp_cable_length_150; + break; + case e1000_gg_cable_length_150: + *min_length = e1000_igp_cable_length_150; + *max_length = e1000_igp_cable_length_180; + break; + default: + return -E1000_ERR_PHY; + break; + } + } else if (hw->phy_type == e1000_phy_igp) { /* For IGP PHY */ + uint16_t cur_agc_value; + uint16_t min_agc_value = IGP01E1000_AGC_LENGTH_TABLE_SIZE; + uint16_t agc_reg_array[IGP01E1000_PHY_CHANNEL_NUM] = + {IGP01E1000_PHY_AGC_A, + IGP01E1000_PHY_AGC_B, + IGP01E1000_PHY_AGC_C, + IGP01E1000_PHY_AGC_D}; + /* Read the AGC registers for all channels */ + for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) { + + ret_val = e1000_read_phy_reg(hw, agc_reg_array[i], &phy_data); + if (ret_val) + return ret_val; + + cur_agc_value = phy_data >> IGP01E1000_AGC_LENGTH_SHIFT; + + /* Value bound check. */ + if ((cur_agc_value >= IGP01E1000_AGC_LENGTH_TABLE_SIZE - 1) || + (cur_agc_value == 0)) + return -E1000_ERR_PHY; + + agc_value += cur_agc_value; + + /* Update minimal AGC value. */ + if (min_agc_value > cur_agc_value) + min_agc_value = cur_agc_value; + } + + /* Remove the minimal AGC result for length < 50m */ + if (agc_value < IGP01E1000_PHY_CHANNEL_NUM * e1000_igp_cable_length_50) { + agc_value -= min_agc_value; + + /* Get the average length of the remaining 3 channels */ + agc_value /= (IGP01E1000_PHY_CHANNEL_NUM - 1); + } else { + /* Get the average length of all the 4 channels. */ + agc_value /= IGP01E1000_PHY_CHANNEL_NUM; + } + + /* Set the range of the calculated length. */ + *min_length = ((e1000_igp_cable_length_table[agc_value] - + IGP01E1000_AGC_RANGE) > 0) ? + (e1000_igp_cable_length_table[agc_value] - + IGP01E1000_AGC_RANGE) : 0; + *max_length = e1000_igp_cable_length_table[agc_value] + + IGP01E1000_AGC_RANGE; + } else if (hw->phy_type == e1000_phy_igp_2 || + hw->phy_type == e1000_phy_igp_3) { + uint16_t cur_agc_index, max_agc_index = 0; + uint16_t min_agc_index = IGP02E1000_AGC_LENGTH_TABLE_SIZE - 1; + uint16_t agc_reg_array[IGP02E1000_PHY_CHANNEL_NUM] = + {IGP02E1000_PHY_AGC_A, + IGP02E1000_PHY_AGC_B, + IGP02E1000_PHY_AGC_C, + IGP02E1000_PHY_AGC_D}; + /* Read the AGC registers for all channels */ + for (i = 0; i < IGP02E1000_PHY_CHANNEL_NUM; i++) { + ret_val = e1000_read_phy_reg(hw, agc_reg_array[i], &phy_data); + if (ret_val) + return ret_val; + + /* Getting bits 15:9, which represent the combination of course and + * fine gain values. The result is a number that can be put into + * the lookup table to obtain the approximate cable length. */ + cur_agc_index = (phy_data >> IGP02E1000_AGC_LENGTH_SHIFT) & + IGP02E1000_AGC_LENGTH_MASK; + + /* Array index bound check. */ + if ((cur_agc_index >= IGP02E1000_AGC_LENGTH_TABLE_SIZE) || + (cur_agc_index == 0)) + return -E1000_ERR_PHY; + + /* Remove min & max AGC values from calculation. */ + if (e1000_igp_2_cable_length_table[min_agc_index] > + e1000_igp_2_cable_length_table[cur_agc_index]) + min_agc_index = cur_agc_index; + if (e1000_igp_2_cable_length_table[max_agc_index] < + e1000_igp_2_cable_length_table[cur_agc_index]) + max_agc_index = cur_agc_index; + + agc_value += e1000_igp_2_cable_length_table[cur_agc_index]; + } + + agc_value -= (e1000_igp_2_cable_length_table[min_agc_index] + + e1000_igp_2_cable_length_table[max_agc_index]); + agc_value /= (IGP02E1000_PHY_CHANNEL_NUM - 2); + + /* Calculate cable length with the error range of +/- 10 meters. */ + *min_length = ((agc_value - IGP02E1000_AGC_RANGE) > 0) ? + (agc_value - IGP02E1000_AGC_RANGE) : 0; + *max_length = agc_value + IGP02E1000_AGC_RANGE; + } + + return E1000_SUCCESS; +} + +/****************************************************************************** + * Check the cable polarity + * + * hw - Struct containing variables accessed by shared code + * polarity - output parameter : 0 - Polarity is not reversed + * 1 - Polarity is reversed. + * + * returns: - E1000_ERR_XXX + * E1000_SUCCESS + * + * For phy's older then IGP, this function simply reads the polarity bit in the + * Phy Status register. For IGP phy's, this bit is valid only if link speed is + * 10 Mbps. If the link speed is 100 Mbps there is no polarity so this bit will + * return 0. If the link speed is 1000 Mbps the polarity status is in the + * IGP01E1000_PHY_PCS_INIT_REG. + *****************************************************************************/ +static int32_t +e1000_check_polarity(struct e1000_hw *hw, + e1000_rev_polarity *polarity) +{ + int32_t ret_val; + uint16_t phy_data; + + DEBUGFUNC("e1000_check_polarity"); + + if ((hw->phy_type == e1000_phy_m88) || + (hw->phy_type == e1000_phy_gg82563)) { + /* return the Polarity bit in the Status register. */ + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, + &phy_data); + if (ret_val) + return ret_val; + *polarity = ((phy_data & M88E1000_PSSR_REV_POLARITY) >> + M88E1000_PSSR_REV_POLARITY_SHIFT) ? + e1000_rev_polarity_reversed : e1000_rev_polarity_normal; + + } else if (hw->phy_type == e1000_phy_igp || + hw->phy_type == e1000_phy_igp_3 || + hw->phy_type == e1000_phy_igp_2) { + /* Read the Status register to check the speed */ + ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS, + &phy_data); + if (ret_val) + return ret_val; + + /* If speed is 1000 Mbps, must read the IGP01E1000_PHY_PCS_INIT_REG to + * find the polarity status */ + if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) == + IGP01E1000_PSSR_SPEED_1000MBPS) { + + /* Read the GIG initialization PCS register (0x00B4) */ + ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PCS_INIT_REG, + &phy_data); + if (ret_val) + return ret_val; + + /* Check the polarity bits */ + *polarity = (phy_data & IGP01E1000_PHY_POLARITY_MASK) ? + e1000_rev_polarity_reversed : e1000_rev_polarity_normal; + } else { + /* For 10 Mbps, read the polarity bit in the status register. (for + * 100 Mbps this bit is always 0) */ + *polarity = (phy_data & IGP01E1000_PSSR_POLARITY_REVERSED) ? + e1000_rev_polarity_reversed : e1000_rev_polarity_normal; + } + } else if (hw->phy_type == e1000_phy_ife) { + ret_val = e1000_read_phy_reg(hw, IFE_PHY_EXTENDED_STATUS_CONTROL, + &phy_data); + if (ret_val) + return ret_val; + *polarity = ((phy_data & IFE_PESC_POLARITY_REVERSED) >> + IFE_PESC_POLARITY_REVERSED_SHIFT) ? + e1000_rev_polarity_reversed : e1000_rev_polarity_normal; + } + return E1000_SUCCESS; +} + +/****************************************************************************** + * Check if Downshift occured + * + * hw - Struct containing variables accessed by shared code + * downshift - output parameter : 0 - No Downshift ocured. + * 1 - Downshift ocured. + * + * returns: - E1000_ERR_XXX + * E1000_SUCCESS + * + * For phy's older then IGP, this function reads the Downshift bit in the Phy + * Specific Status register. For IGP phy's, it reads the Downgrade bit in the + * Link Health register. In IGP this bit is latched high, so the driver must + * read it immediately after link is established. + *****************************************************************************/ +static int32_t +e1000_check_downshift(struct e1000_hw *hw) +{ + int32_t ret_val; + uint16_t phy_data; + + DEBUGFUNC("e1000_check_downshift"); + + if (hw->phy_type == e1000_phy_igp || + hw->phy_type == e1000_phy_igp_3 || + hw->phy_type == e1000_phy_igp_2) { + ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_LINK_HEALTH, + &phy_data); + if (ret_val) + return ret_val; + + hw->speed_downgraded = (phy_data & IGP01E1000_PLHR_SS_DOWNGRADE) ? 1 : 0; + } else if ((hw->phy_type == e1000_phy_m88) || + (hw->phy_type == e1000_phy_gg82563)) { + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, + &phy_data); + if (ret_val) + return ret_val; + + hw->speed_downgraded = (phy_data & M88E1000_PSSR_DOWNSHIFT) >> + M88E1000_PSSR_DOWNSHIFT_SHIFT; + } else if (hw->phy_type == e1000_phy_ife) { + /* e1000_phy_ife supports 10/100 speed only */ + hw->speed_downgraded = FALSE; + } + + return E1000_SUCCESS; +} + +/***************************************************************************** + * + * 82541_rev_2 & 82547_rev_2 have the capability to configure the DSP when a + * gigabit link is achieved to improve link quality. + * + * hw: Struct containing variables accessed by shared code + * + * returns: - E1000_ERR_PHY if fail to read/write the PHY + * E1000_SUCCESS at any other case. + * + ****************************************************************************/ + +static int32_t +e1000_config_dsp_after_link_change(struct e1000_hw *hw, + boolean_t link_up) +{ + int32_t ret_val; + uint16_t phy_data, phy_saved_data, speed, duplex, i; + uint16_t dsp_reg_array[IGP01E1000_PHY_CHANNEL_NUM] = + {IGP01E1000_PHY_AGC_PARAM_A, + IGP01E1000_PHY_AGC_PARAM_B, + IGP01E1000_PHY_AGC_PARAM_C, + IGP01E1000_PHY_AGC_PARAM_D}; + uint16_t min_length, max_length; + + DEBUGFUNC("e1000_config_dsp_after_link_change"); + + if (hw->phy_type != e1000_phy_igp) + return E1000_SUCCESS; + + if (link_up) { + ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex); + if (ret_val) { + DEBUGOUT("Error getting link speed and duplex\n"); + return ret_val; + } + + if (speed == SPEED_1000) { + + ret_val = e1000_get_cable_length(hw, &min_length, &max_length); + if (ret_val) + return ret_val; + + if ((hw->dsp_config_state == e1000_dsp_config_enabled) && + min_length >= e1000_igp_cable_length_50) { + + for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) { + ret_val = e1000_read_phy_reg(hw, dsp_reg_array[i], + &phy_data); + if (ret_val) + return ret_val; + + phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX; + + ret_val = e1000_write_phy_reg(hw, dsp_reg_array[i], + phy_data); + if (ret_val) + return ret_val; + } + hw->dsp_config_state = e1000_dsp_config_activated; + } + + if ((hw->ffe_config_state == e1000_ffe_config_enabled) && + (min_length < e1000_igp_cable_length_50)) { + + uint16_t ffe_idle_err_timeout = FFE_IDLE_ERR_COUNT_TIMEOUT_20; + uint32_t idle_errs = 0; + + /* clear previous idle error counts */ + ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, + &phy_data); + if (ret_val) + return ret_val; + + for (i = 0; i < ffe_idle_err_timeout; i++) { + udelay(1000); + ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, + &phy_data); + if (ret_val) + return ret_val; + + idle_errs += (phy_data & SR_1000T_IDLE_ERROR_CNT); + if (idle_errs > SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT) { + hw->ffe_config_state = e1000_ffe_config_active; + + ret_val = e1000_write_phy_reg(hw, + IGP01E1000_PHY_DSP_FFE, + IGP01E1000_PHY_DSP_FFE_CM_CP); + if (ret_val) + return ret_val; + break; + } + + if (idle_errs) + ffe_idle_err_timeout = FFE_IDLE_ERR_COUNT_TIMEOUT_100; + } + } + } + } else { + if (hw->dsp_config_state == e1000_dsp_config_activated) { + /* Save off the current value of register 0x2F5B to be restored at + * the end of the routines. */ + ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data); + + if (ret_val) + return ret_val; + + /* Disable the PHY transmitter */ + ret_val = e1000_write_phy_reg(hw, 0x2F5B, 0x0003); + + if (ret_val) + return ret_val; + + mdelay(20); + + ret_val = e1000_write_phy_reg(hw, 0x0000, + IGP01E1000_IEEE_FORCE_GIGA); + if (ret_val) + return ret_val; + for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) { + ret_val = e1000_read_phy_reg(hw, dsp_reg_array[i], &phy_data); + if (ret_val) + return ret_val; + + phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX; + phy_data |= IGP01E1000_PHY_EDAC_SIGN_EXT_9_BITS; + + ret_val = e1000_write_phy_reg(hw,dsp_reg_array[i], phy_data); + if (ret_val) + return ret_val; + } + + ret_val = e1000_write_phy_reg(hw, 0x0000, + IGP01E1000_IEEE_RESTART_AUTONEG); + if (ret_val) + return ret_val; + + mdelay(20); + + /* Now enable the transmitter */ + ret_val = e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data); + + if (ret_val) + return ret_val; + + hw->dsp_config_state = e1000_dsp_config_enabled; + } + + if (hw->ffe_config_state == e1000_ffe_config_active) { + /* Save off the current value of register 0x2F5B to be restored at + * the end of the routines. */ + ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data); + + if (ret_val) + return ret_val; + + /* Disable the PHY transmitter */ + ret_val = e1000_write_phy_reg(hw, 0x2F5B, 0x0003); + + if (ret_val) + return ret_val; + + mdelay(20); + + ret_val = e1000_write_phy_reg(hw, 0x0000, + IGP01E1000_IEEE_FORCE_GIGA); + if (ret_val) + return ret_val; + ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_DSP_FFE, + IGP01E1000_PHY_DSP_FFE_DEFAULT); + if (ret_val) + return ret_val; + + ret_val = e1000_write_phy_reg(hw, 0x0000, + IGP01E1000_IEEE_RESTART_AUTONEG); + if (ret_val) + return ret_val; + + mdelay(20); + + /* Now enable the transmitter */ + ret_val = e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data); + + if (ret_val) + return ret_val; + + hw->ffe_config_state = e1000_ffe_config_enabled; + } + } + return E1000_SUCCESS; +} + +/***************************************************************************** + * Set PHY to class A mode + * Assumes the following operations will follow to enable the new class mode. + * 1. Do a PHY soft reset + * 2. Restart auto-negotiation or force link. + * + * hw - Struct containing variables accessed by shared code + ****************************************************************************/ +static int32_t +e1000_set_phy_mode(struct e1000_hw *hw) +{ + int32_t ret_val; + uint16_t eeprom_data; + + DEBUGFUNC("e1000_set_phy_mode"); + + if ((hw->mac_type == e1000_82545_rev_3) && + (hw->media_type == e1000_media_type_copper)) { + ret_val = e1000_read_eeprom(hw, EEPROM_PHY_CLASS_WORD, 1, &eeprom_data); + if (ret_val) { + return ret_val; + } + + if ((eeprom_data != EEPROM_RESERVED_WORD) && + (eeprom_data & EEPROM_PHY_CLASS_A)) { + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x000B); + if (ret_val) + return ret_val; + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0x8104); + if (ret_val) + return ret_val; + + hw->phy_reset_disable = FALSE; + } + } + + return E1000_SUCCESS; +} + +/***************************************************************************** + * + * This function sets the lplu state according to the active flag. When + * activating lplu this function also disables smart speed and vise versa. + * lplu will not be activated unless the device autonegotiation advertisment + * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes. + * hw: Struct containing variables accessed by shared code + * active - true to enable lplu false to disable lplu. + * + * returns: - E1000_ERR_PHY if fail to read/write the PHY + * E1000_SUCCESS at any other case. + * + ****************************************************************************/ + +static int32_t +e1000_set_d3_lplu_state(struct e1000_hw *hw, + boolean_t active) +{ + uint32_t phy_ctrl = 0; + int32_t ret_val; + uint16_t phy_data; + DEBUGFUNC("e1000_set_d3_lplu_state"); + + if (hw->phy_type != e1000_phy_igp && hw->phy_type != e1000_phy_igp_2 + && hw->phy_type != e1000_phy_igp_3) + return E1000_SUCCESS; + + /* During driver activity LPLU should not be used or it will attain link + * from the lowest speeds starting from 10Mbps. The capability is used for + * Dx transitions and states */ + if (hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2) { + ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO, &phy_data); + if (ret_val) + return ret_val; + } else if (hw->mac_type == e1000_ich8lan) { + /* MAC writes into PHY register based on the state transition + * and start auto-negotiation. SW driver can overwrite the settings + * in CSR PHY power control E1000_PHY_CTRL register. */ + phy_ctrl = E1000_READ_REG(hw, PHY_CTRL); + } else { + ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data); + if (ret_val) + return ret_val; + } + + if (!active) { + if (hw->mac_type == e1000_82541_rev_2 || + hw->mac_type == e1000_82547_rev_2) { + phy_data &= ~IGP01E1000_GMII_FLEX_SPD; + ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, phy_data); + if (ret_val) + return ret_val; + } else { + if (hw->mac_type == e1000_ich8lan) { + phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU; + E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); + } else { + phy_data &= ~IGP02E1000_PM_D3_LPLU; + ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, + phy_data); + if (ret_val) + return ret_val; + } + } + + /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during + * Dx states where the power conservation is most important. During + * driver activity we should enable SmartSpeed, so performance is + * maintained. */ + if (hw->smart_speed == e1000_smart_speed_on) { + ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + &phy_data); + if (ret_val) + return ret_val; + + phy_data |= IGP01E1000_PSCFR_SMART_SPEED; + ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + phy_data); + if (ret_val) + return ret_val; + } else if (hw->smart_speed == e1000_smart_speed_off) { + ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + &phy_data); + if (ret_val) + return ret_val; + + phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + phy_data); + if (ret_val) + return ret_val; + } + + } else if ((hw->autoneg_advertised == AUTONEG_ADVERTISE_SPEED_DEFAULT) || + (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_ALL ) || + (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_100_ALL)) { + + if (hw->mac_type == e1000_82541_rev_2 || + hw->mac_type == e1000_82547_rev_2) { + phy_data |= IGP01E1000_GMII_FLEX_SPD; + ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, phy_data); + if (ret_val) + return ret_val; + } else { + if (hw->mac_type == e1000_ich8lan) { + phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU; + E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); + } else { + phy_data |= IGP02E1000_PM_D3_LPLU; + ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, + phy_data); + if (ret_val) + return ret_val; + } + } + + /* When LPLU is enabled we should disable SmartSpeed */ + ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data); + if (ret_val) + return ret_val; + + phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, phy_data); + if (ret_val) + return ret_val; + + } + return E1000_SUCCESS; +} + +/***************************************************************************** + * + * This function sets the lplu d0 state according to the active flag. When + * activating lplu this function also disables smart speed and vise versa. + * lplu will not be activated unless the device autonegotiation advertisment + * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes. + * hw: Struct containing variables accessed by shared code + * active - true to enable lplu false to disable lplu. + * + * returns: - E1000_ERR_PHY if fail to read/write the PHY + * E1000_SUCCESS at any other case. + * + ****************************************************************************/ + +static int32_t +e1000_set_d0_lplu_state(struct e1000_hw *hw, + boolean_t active) +{ + uint32_t phy_ctrl = 0; + int32_t ret_val; + uint16_t phy_data; + DEBUGFUNC("e1000_set_d0_lplu_state"); + + if (hw->mac_type <= e1000_82547_rev_2) + return E1000_SUCCESS; + + if (hw->mac_type == e1000_ich8lan) { + phy_ctrl = E1000_READ_REG(hw, PHY_CTRL); + } else { + ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data); + if (ret_val) + return ret_val; + } + + if (!active) { + if (hw->mac_type == e1000_ich8lan) { + phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU; + E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); + } else { + phy_data &= ~IGP02E1000_PM_D0_LPLU; + ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data); + if (ret_val) + return ret_val; + } + + /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during + * Dx states where the power conservation is most important. During + * driver activity we should enable SmartSpeed, so performance is + * maintained. */ + if (hw->smart_speed == e1000_smart_speed_on) { + ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + &phy_data); + if (ret_val) + return ret_val; + + phy_data |= IGP01E1000_PSCFR_SMART_SPEED; + ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + phy_data); + if (ret_val) + return ret_val; + } else if (hw->smart_speed == e1000_smart_speed_off) { + ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + &phy_data); + if (ret_val) + return ret_val; + + phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + phy_data); + if (ret_val) + return ret_val; + } + + + } else { + + if (hw->mac_type == e1000_ich8lan) { + phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU; + E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); + } else { + phy_data |= IGP02E1000_PM_D0_LPLU; + ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data); + if (ret_val) + return ret_val; + } + + /* When LPLU is enabled we should disable SmartSpeed */ + ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data); + if (ret_val) + return ret_val; + + phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, phy_data); + if (ret_val) + return ret_val; + + } + return E1000_SUCCESS; +} + +/****************************************************************************** + * Change VCO speed register to improve Bit Error Rate performance of SERDES. + * + * hw - Struct containing variables accessed by shared code + *****************************************************************************/ +static int32_t +e1000_set_vco_speed(struct e1000_hw *hw) +{ + int32_t ret_val; + uint16_t default_page = 0; + uint16_t phy_data; + + DEBUGFUNC("e1000_set_vco_speed"); + + switch (hw->mac_type) { + case e1000_82545_rev_3: + case e1000_82546_rev_3: + break; + default: + return E1000_SUCCESS; + } + + /* Set PHY register 30, page 5, bit 8 to 0 */ + + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, &default_page); + if (ret_val) + return ret_val; + + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0005); + if (ret_val) + return ret_val; + + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data); + if (ret_val) + return ret_val; + + phy_data &= ~M88E1000_PHY_VCO_REG_BIT8; + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data); + if (ret_val) + return ret_val; + + /* Set PHY register 30, page 4, bit 11 to 1 */ + + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0004); + if (ret_val) + return ret_val; + + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data); + if (ret_val) + return ret_val; + + phy_data |= M88E1000_PHY_VCO_REG_BIT11; + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data); + if (ret_val) + return ret_val; + + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, default_page); + if (ret_val) + return ret_val; + + return E1000_SUCCESS; +} + + +/***************************************************************************** + * This function reads the cookie from ARC ram. + * + * returns: - E1000_SUCCESS . + ****************************************************************************/ +static int32_t +e1000_host_if_read_cookie(struct e1000_hw * hw, uint8_t *buffer) +{ + uint8_t i; + uint32_t offset = E1000_MNG_DHCP_COOKIE_OFFSET; + uint8_t length = E1000_MNG_DHCP_COOKIE_LENGTH; + + length = (length >> 2); + offset = (offset >> 2); + + for (i = 0; i < length; i++) { + *((uint32_t *) buffer + i) = + E1000_READ_REG_ARRAY_DWORD(hw, HOST_IF, offset + i); + } + return E1000_SUCCESS; +} + + +/***************************************************************************** + * This function checks whether the HOST IF is enabled for command operaton + * and also checks whether the previous command is completed. + * It busy waits in case of previous command is not completed. + * + * returns: - E1000_ERR_HOST_INTERFACE_COMMAND in case if is not ready or + * timeout + * - E1000_SUCCESS for success. + ****************************************************************************/ +static int32_t +e1000_mng_enable_host_if(struct e1000_hw * hw) +{ + uint32_t hicr; + uint8_t i; + + /* Check that the host interface is enabled. */ + hicr = E1000_READ_REG(hw, HICR); + if ((hicr & E1000_HICR_EN) == 0) { + DEBUGOUT("E1000_HOST_EN bit disabled.\n"); + return -E1000_ERR_HOST_INTERFACE_COMMAND; + } + /* check the previous command is completed */ + for (i = 0; i < E1000_MNG_DHCP_COMMAND_TIMEOUT; i++) { + hicr = E1000_READ_REG(hw, HICR); + if (!(hicr & E1000_HICR_C)) + break; + mdelay(1); + } + + if (i == E1000_MNG_DHCP_COMMAND_TIMEOUT) { + DEBUGOUT("Previous command timeout failed .\n"); + return -E1000_ERR_HOST_INTERFACE_COMMAND; + } + return E1000_SUCCESS; +} + +/***************************************************************************** + * This function writes the buffer content at the offset given on the host if. + * It also does alignment considerations to do the writes in most efficient way. + * Also fills up the sum of the buffer in *buffer parameter. + * + * returns - E1000_SUCCESS for success. + ****************************************************************************/ +static int32_t +e1000_mng_host_if_write(struct e1000_hw * hw, uint8_t *buffer, + uint16_t length, uint16_t offset, uint8_t *sum) +{ + uint8_t *tmp; + uint8_t *bufptr = buffer; + uint32_t data = 0; + uint16_t remaining, i, j, prev_bytes; + + /* sum = only sum of the data and it is not checksum */ + + if (length == 0 || offset + length > E1000_HI_MAX_MNG_DATA_LENGTH) { + return -E1000_ERR_PARAM; + } + + tmp = (uint8_t *)&data; + prev_bytes = offset & 0x3; + offset &= 0xFFFC; + offset >>= 2; + + if (prev_bytes) { + data = E1000_READ_REG_ARRAY_DWORD(hw, HOST_IF, offset); + for (j = prev_bytes; j < sizeof(uint32_t); j++) { + *(tmp + j) = *bufptr++; + *sum += *(tmp + j); + } + E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, offset, data); + length -= j - prev_bytes; + offset++; + } + + remaining = length & 0x3; + length -= remaining; + + /* Calculate length in DWORDs */ + length >>= 2; + + /* The device driver writes the relevant command block into the + * ram area. */ + for (i = 0; i < length; i++) { + for (j = 0; j < sizeof(uint32_t); j++) { + *(tmp + j) = *bufptr++; + *sum += *(tmp + j); + } + + E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, offset + i, data); + } + if (remaining) { + for (j = 0; j < sizeof(uint32_t); j++) { + if (j < remaining) + *(tmp + j) = *bufptr++; + else + *(tmp + j) = 0; + + *sum += *(tmp + j); + } + E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, offset + i, data); + } + + return E1000_SUCCESS; +} + + +/***************************************************************************** + * This function writes the command header after does the checksum calculation. + * + * returns - E1000_SUCCESS for success. + ****************************************************************************/ +static int32_t +e1000_mng_write_cmd_header(struct e1000_hw * hw, + struct e1000_host_mng_command_header * hdr) +{ + uint16_t i; + uint8_t sum; + uint8_t *buffer; + + /* Write the whole command header structure which includes sum of + * the buffer */ + + uint16_t length = sizeof(struct e1000_host_mng_command_header); + + sum = hdr->checksum; + hdr->checksum = 0; + + buffer = (uint8_t *) hdr; + i = length; + while (i--) + sum += buffer[i]; + + hdr->checksum = 0 - sum; + + length >>= 2; + /* The device driver writes the relevant command block into the ram area. */ + for (i = 0; i < length; i++) { + E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, i, *((uint32_t *) hdr + i)); + E1000_WRITE_FLUSH(hw); + } + + return E1000_SUCCESS; +} + + +/***************************************************************************** + * This function indicates to ARC that a new command is pending which completes + * one write operation by the driver. + * + * returns - E1000_SUCCESS for success. + ****************************************************************************/ +static int32_t +e1000_mng_write_commit(struct e1000_hw * hw) +{ + uint32_t hicr; + + hicr = E1000_READ_REG(hw, HICR); + /* Setting this bit tells the ARC that a new command is pending. */ + E1000_WRITE_REG(hw, HICR, hicr | E1000_HICR_C); + + return E1000_SUCCESS; +} + + +/***************************************************************************** + * This function checks the mode of the firmware. + * + * returns - TRUE when the mode is IAMT or FALSE. + ****************************************************************************/ +boolean_t +e1000_check_mng_mode(struct e1000_hw *hw) +{ + uint32_t fwsm; + + fwsm = E1000_READ_REG(hw, FWSM); + + if (hw->mac_type == e1000_ich8lan) { + if ((fwsm & E1000_FWSM_MODE_MASK) == + (E1000_MNG_ICH_IAMT_MODE << E1000_FWSM_MODE_SHIFT)) + return TRUE; + } else if ((fwsm & E1000_FWSM_MODE_MASK) == + (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT)) + return TRUE; + + return FALSE; +} + + +/***************************************************************************** + * This function writes the dhcp info . + ****************************************************************************/ +int32_t +e1000_mng_write_dhcp_info(struct e1000_hw * hw, uint8_t *buffer, + uint16_t length) +{ + int32_t ret_val; + struct e1000_host_mng_command_header hdr; + + hdr.command_id = E1000_MNG_DHCP_TX_PAYLOAD_CMD; + hdr.command_length = length; + hdr.reserved1 = 0; + hdr.reserved2 = 0; + hdr.checksum = 0; + + ret_val = e1000_mng_enable_host_if(hw); + if (ret_val == E1000_SUCCESS) { + ret_val = e1000_mng_host_if_write(hw, buffer, length, sizeof(hdr), + &(hdr.checksum)); + if (ret_val == E1000_SUCCESS) { + ret_val = e1000_mng_write_cmd_header(hw, &hdr); + if (ret_val == E1000_SUCCESS) + ret_val = e1000_mng_write_commit(hw); + } + } + return ret_val; +} + + +/***************************************************************************** + * This function calculates the checksum. + * + * returns - checksum of buffer contents. + ****************************************************************************/ +static uint8_t +e1000_calculate_mng_checksum(char *buffer, uint32_t length) +{ + uint8_t sum = 0; + uint32_t i; + + if (!buffer) + return 0; + + for (i=0; i < length; i++) + sum += buffer[i]; + + return (uint8_t) (0 - sum); +} + +/***************************************************************************** + * This function checks whether tx pkt filtering needs to be enabled or not. + * + * returns - TRUE for packet filtering or FALSE. + ****************************************************************************/ +boolean_t +e1000_enable_tx_pkt_filtering(struct e1000_hw *hw) +{ + /* called in init as well as watchdog timer functions */ + + int32_t ret_val, checksum; + boolean_t tx_filter = FALSE; + struct e1000_host_mng_dhcp_cookie *hdr = &(hw->mng_cookie); + uint8_t *buffer = (uint8_t *) &(hw->mng_cookie); + + if (e1000_check_mng_mode(hw)) { + ret_val = e1000_mng_enable_host_if(hw); + if (ret_val == E1000_SUCCESS) { + ret_val = e1000_host_if_read_cookie(hw, buffer); + if (ret_val == E1000_SUCCESS) { + checksum = hdr->checksum; + hdr->checksum = 0; + if ((hdr->signature == E1000_IAMT_SIGNATURE) && + checksum == e1000_calculate_mng_checksum((char *)buffer, + E1000_MNG_DHCP_COOKIE_LENGTH)) { + if (hdr->status & + E1000_MNG_DHCP_COOKIE_STATUS_PARSING_SUPPORT) + tx_filter = TRUE; + } else + tx_filter = TRUE; + } else + tx_filter = TRUE; + } + } + + hw->tx_pkt_filtering = tx_filter; + return tx_filter; +} + +/****************************************************************************** + * Verifies the hardware needs to allow ARPs to be processed by the host + * + * hw - Struct containing variables accessed by shared code + * + * returns: - TRUE/FALSE + * + *****************************************************************************/ +uint32_t +e1000_enable_mng_pass_thru(struct e1000_hw *hw) +{ + uint32_t manc; + uint32_t fwsm, factps; + + if (hw->asf_firmware_present) { + manc = E1000_READ_REG(hw, MANC); + + if (!(manc & E1000_MANC_RCV_TCO_EN) || + !(manc & E1000_MANC_EN_MAC_ADDR_FILTER)) + return FALSE; + if (e1000_arc_subsystem_valid(hw) == TRUE) { + fwsm = E1000_READ_REG(hw, FWSM); + factps = E1000_READ_REG(hw, FACTPS); + + if ((((fwsm & E1000_FWSM_MODE_MASK) >> E1000_FWSM_MODE_SHIFT) == + e1000_mng_mode_pt) && !(factps & E1000_FACTPS_MNGCG)) + return TRUE; + } else + if ((manc & E1000_MANC_SMBUS_EN) && !(manc & E1000_MANC_ASF_EN)) + return TRUE; + } + return FALSE; +} + +static int32_t +e1000_polarity_reversal_workaround(struct e1000_hw *hw) +{ + int32_t ret_val; + uint16_t mii_status_reg; + uint16_t i; + + /* Polarity reversal workaround for forced 10F/10H links. */ + + /* Disable the transmitter on the PHY */ + + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019); + if (ret_val) + return ret_val; + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFFF); + if (ret_val) + return ret_val; + + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000); + if (ret_val) + return ret_val; + + /* This loop will early-out if the NO link condition has been met. */ + for (i = PHY_FORCE_TIME; i > 0; i--) { + /* Read the MII Status Register and wait for Link Status bit + * to be clear. + */ + + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + return ret_val; + + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + return ret_val; + + if ((mii_status_reg & ~MII_SR_LINK_STATUS) == 0) break; + mdelay(100); + } + + /* Recommended delay time after link has been lost */ + mdelay(1000); + + /* Now we will re-enable th transmitter on the PHY */ + + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019); + if (ret_val) + return ret_val; + mdelay(50); + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFF0); + if (ret_val) + return ret_val; + mdelay(50); + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFF00); + if (ret_val) + return ret_val; + mdelay(50); + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0x0000); + if (ret_val) + return ret_val; + + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000); + if (ret_val) + return ret_val; + + /* This loop will early-out if the link condition has been met. */ + for (i = PHY_FORCE_TIME; i > 0; i--) { + /* Read the MII Status Register and wait for Link Status bit + * to be set. + */ + + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + return ret_val; + + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + return ret_val; + + if (mii_status_reg & MII_SR_LINK_STATUS) break; + mdelay(100); + } + return E1000_SUCCESS; +} + +/*************************************************************************** + * + * Disables PCI-Express master access. + * + * hw: Struct containing variables accessed by shared code + * + * returns: - none. + * + ***************************************************************************/ +static void +e1000_set_pci_express_master_disable(struct e1000_hw *hw) +{ + uint32_t ctrl; + + DEBUGFUNC("e1000_set_pci_express_master_disable"); + + if (hw->bus_type != e1000_bus_type_pci_express) + return; + + ctrl = E1000_READ_REG(hw, CTRL); + ctrl |= E1000_CTRL_GIO_MASTER_DISABLE; + E1000_WRITE_REG(hw, CTRL, ctrl); +} + +/******************************************************************************* + * + * Disables PCI-Express master access and verifies there are no pending requests + * + * hw: Struct containing variables accessed by shared code + * + * returns: - E1000_ERR_MASTER_REQUESTS_PENDING if master disable bit hasn't + * caused the master requests to be disabled. + * E1000_SUCCESS master requests disabled. + * + ******************************************************************************/ +int32_t +e1000_disable_pciex_master(struct e1000_hw *hw) +{ + int32_t timeout = MASTER_DISABLE_TIMEOUT; /* 80ms */ + + DEBUGFUNC("e1000_disable_pciex_master"); + + if (hw->bus_type != e1000_bus_type_pci_express) + return E1000_SUCCESS; + + e1000_set_pci_express_master_disable(hw); + + while (timeout) { + if (!(E1000_READ_REG(hw, STATUS) & E1000_STATUS_GIO_MASTER_ENABLE)) + break; + else + udelay(100); + timeout--; + } + + if (!timeout) { + DEBUGOUT("Master requests are pending.\n"); + return -E1000_ERR_MASTER_REQUESTS_PENDING; + } + + return E1000_SUCCESS; +} + +/******************************************************************************* + * + * Check for EEPROM Auto Read bit done. + * + * hw: Struct containing variables accessed by shared code + * + * returns: - E1000_ERR_RESET if fail to reset MAC + * E1000_SUCCESS at any other case. + * + ******************************************************************************/ +static int32_t +e1000_get_auto_rd_done(struct e1000_hw *hw) +{ + int32_t timeout = AUTO_READ_DONE_TIMEOUT; + + DEBUGFUNC("e1000_get_auto_rd_done"); + + switch (hw->mac_type) { + default: + msleep(5); + break; + case e1000_82571: + case e1000_82572: + case e1000_82573: + case e1000_80003es2lan: + case e1000_ich8lan: + while (timeout) { + if (E1000_READ_REG(hw, EECD) & E1000_EECD_AUTO_RD) + break; + else msleep(1); + timeout--; + } + + if (!timeout) { + DEBUGOUT("Auto read by HW from EEPROM has not completed.\n"); + return -E1000_ERR_RESET; + } + break; + } + + /* PHY configuration from NVM just starts after EECD_AUTO_RD sets to high. + * Need to wait for PHY configuration completion before accessing NVM + * and PHY. */ + if (hw->mac_type == e1000_82573) + msleep(25); + + return E1000_SUCCESS; +} + +/*************************************************************************** + * Checks if the PHY configuration is done + * + * hw: Struct containing variables accessed by shared code + * + * returns: - E1000_ERR_RESET if fail to reset MAC + * E1000_SUCCESS at any other case. + * + ***************************************************************************/ +static int32_t +e1000_get_phy_cfg_done(struct e1000_hw *hw) +{ + int32_t timeout = PHY_CFG_TIMEOUT; + uint32_t cfg_mask = E1000_EEPROM_CFG_DONE; + + DEBUGFUNC("e1000_get_phy_cfg_done"); + + switch (hw->mac_type) { + default: + mdelay(10); + break; + case e1000_80003es2lan: + /* Separate *_CFG_DONE_* bit for each port */ + if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1) + cfg_mask = E1000_EEPROM_CFG_DONE_PORT_1; + /* Fall Through */ + case e1000_82571: + case e1000_82572: + while (timeout) { + if (E1000_READ_REG(hw, EEMNGCTL) & cfg_mask) + break; + else + msleep(1); + timeout--; + } + if (!timeout) { + DEBUGOUT("MNG configuration cycle has not completed.\n"); + return -E1000_ERR_RESET; + } + break; + } + + return E1000_SUCCESS; +} + +/*************************************************************************** + * + * Using the combination of SMBI and SWESMBI semaphore bits when resetting + * adapter or Eeprom access. + * + * hw: Struct containing variables accessed by shared code + * + * returns: - E1000_ERR_EEPROM if fail to access EEPROM. + * E1000_SUCCESS at any other case. + * + ***************************************************************************/ +static int32_t +e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw) +{ + int32_t timeout; + uint32_t swsm; + + DEBUGFUNC("e1000_get_hw_eeprom_semaphore"); + + if (!hw->eeprom_semaphore_present) + return E1000_SUCCESS; + + if (hw->mac_type == e1000_80003es2lan) { + /* Get the SW semaphore. */ + if (e1000_get_software_semaphore(hw) != E1000_SUCCESS) + return -E1000_ERR_EEPROM; + } + + /* Get the FW semaphore. */ + timeout = hw->eeprom.word_size + 1; + while (timeout) { + swsm = E1000_READ_REG(hw, SWSM); + swsm |= E1000_SWSM_SWESMBI; + E1000_WRITE_REG(hw, SWSM, swsm); + /* if we managed to set the bit we got the semaphore. */ + swsm = E1000_READ_REG(hw, SWSM); + if (swsm & E1000_SWSM_SWESMBI) + break; + + udelay(50); + timeout--; + } + + if (!timeout) { + /* Release semaphores */ + e1000_put_hw_eeprom_semaphore(hw); + DEBUGOUT("Driver can't access the Eeprom - SWESMBI bit is set.\n"); + return -E1000_ERR_EEPROM; + } + + return E1000_SUCCESS; +} + +/*************************************************************************** + * This function clears HW semaphore bits. + * + * hw: Struct containing variables accessed by shared code + * + * returns: - None. + * + ***************************************************************************/ +static void +e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw) +{ + uint32_t swsm; + + DEBUGFUNC("e1000_put_hw_eeprom_semaphore"); + + if (!hw->eeprom_semaphore_present) + return; + + swsm = E1000_READ_REG(hw, SWSM); + if (hw->mac_type == e1000_80003es2lan) { + /* Release both semaphores. */ + swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI); + } else + swsm &= ~(E1000_SWSM_SWESMBI); + E1000_WRITE_REG(hw, SWSM, swsm); +} + +/*************************************************************************** + * + * Obtaining software semaphore bit (SMBI) before resetting PHY. + * + * hw: Struct containing variables accessed by shared code + * + * returns: - E1000_ERR_RESET if fail to obtain semaphore. + * E1000_SUCCESS at any other case. + * + ***************************************************************************/ +static int32_t +e1000_get_software_semaphore(struct e1000_hw *hw) +{ + int32_t timeout = hw->eeprom.word_size + 1; + uint32_t swsm; + + DEBUGFUNC("e1000_get_software_semaphore"); + + if (hw->mac_type != e1000_80003es2lan) { + return E1000_SUCCESS; + } + + while (timeout) { + swsm = E1000_READ_REG(hw, SWSM); + /* If SMBI bit cleared, it is now set and we hold the semaphore */ + if (!(swsm & E1000_SWSM_SMBI)) + break; + mdelay(1); + timeout--; + } + + if (!timeout) { + DEBUGOUT("Driver can't access device - SMBI bit is set.\n"); + return -E1000_ERR_RESET; + } + + return E1000_SUCCESS; +} + +/*************************************************************************** + * + * Release semaphore bit (SMBI). + * + * hw: Struct containing variables accessed by shared code + * + ***************************************************************************/ +static void +e1000_release_software_semaphore(struct e1000_hw *hw) +{ + uint32_t swsm; + + DEBUGFUNC("e1000_release_software_semaphore"); + + if (hw->mac_type != e1000_80003es2lan) { + return; + } + + swsm = E1000_READ_REG(hw, SWSM); + /* Release the SW semaphores.*/ + swsm &= ~E1000_SWSM_SMBI; + E1000_WRITE_REG(hw, SWSM, swsm); +} + +/****************************************************************************** + * Checks if PHY reset is blocked due to SOL/IDER session, for example. + * Returning E1000_BLK_PHY_RESET isn't necessarily an error. But it's up to + * the caller to figure out how to deal with it. + * + * hw - Struct containing variables accessed by shared code + * + * returns: - E1000_BLK_PHY_RESET + * E1000_SUCCESS + * + *****************************************************************************/ +int32_t +e1000_check_phy_reset_block(struct e1000_hw *hw) +{ + uint32_t manc = 0; + uint32_t fwsm = 0; + + if (hw->mac_type == e1000_ich8lan) { + fwsm = E1000_READ_REG(hw, FWSM); + return (fwsm & E1000_FWSM_RSPCIPHY) ? E1000_SUCCESS + : E1000_BLK_PHY_RESET; + } + + if (hw->mac_type > e1000_82547_rev_2) + manc = E1000_READ_REG(hw, MANC); + return (manc & E1000_MANC_BLK_PHY_RST_ON_IDE) ? + E1000_BLK_PHY_RESET : E1000_SUCCESS; +} + +static uint8_t +e1000_arc_subsystem_valid(struct e1000_hw *hw) +{ + uint32_t fwsm; + + /* On 8257x silicon, registers in the range of 0x8800 - 0x8FFC + * may not be provided a DMA clock when no manageability features are + * enabled. We do not want to perform any reads/writes to these registers + * if this is the case. We read FWSM to determine the manageability mode. + */ + switch (hw->mac_type) { + case e1000_82571: + case e1000_82572: + case e1000_82573: + case e1000_80003es2lan: + fwsm = E1000_READ_REG(hw, FWSM); + if ((fwsm & E1000_FWSM_MODE_MASK) != 0) + return TRUE; + break; + case e1000_ich8lan: + return TRUE; + default: + break; + } + return FALSE; +} + + +/****************************************************************************** + * Configure PCI-Ex no-snoop + * + * hw - Struct containing variables accessed by shared code. + * no_snoop - Bitmap of no-snoop events. + * + * returns: E1000_SUCCESS + * + *****************************************************************************/ +static int32_t +e1000_set_pci_ex_no_snoop(struct e1000_hw *hw, uint32_t no_snoop) +{ + uint32_t gcr_reg = 0; + + DEBUGFUNC("e1000_set_pci_ex_no_snoop"); + + if (hw->bus_type == e1000_bus_type_unknown) + e1000_get_bus_info(hw); + + if (hw->bus_type != e1000_bus_type_pci_express) + return E1000_SUCCESS; + + if (no_snoop) { + gcr_reg = E1000_READ_REG(hw, GCR); + gcr_reg &= ~(PCI_EX_NO_SNOOP_ALL); + gcr_reg |= no_snoop; + E1000_WRITE_REG(hw, GCR, gcr_reg); + } + if (hw->mac_type == e1000_ich8lan) { + uint32_t ctrl_ext; + + E1000_WRITE_REG(hw, GCR, PCI_EX_82566_SNOOP_ALL); + + ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); + ctrl_ext |= E1000_CTRL_EXT_RO_DIS; + E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); + } + + return E1000_SUCCESS; +} + +/*************************************************************************** + * + * Get software semaphore FLAG bit (SWFLAG). + * SWFLAG is used to synchronize the access to all shared resource between + * SW, FW and HW. + * + * hw: Struct containing variables accessed by shared code + * + ***************************************************************************/ +static int32_t +e1000_get_software_flag(struct e1000_hw *hw) +{ + int32_t timeout = PHY_CFG_TIMEOUT; + uint32_t extcnf_ctrl; + + DEBUGFUNC("e1000_get_software_flag"); + + if (hw->mac_type == e1000_ich8lan) { + while (timeout) { + extcnf_ctrl = E1000_READ_REG(hw, EXTCNF_CTRL); + extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG; + E1000_WRITE_REG(hw, EXTCNF_CTRL, extcnf_ctrl); + + extcnf_ctrl = E1000_READ_REG(hw, EXTCNF_CTRL); + if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG) + break; + mdelay(1); + timeout--; + } + + if (!timeout) { + DEBUGOUT("FW or HW locks the resource too long.\n"); + return -E1000_ERR_CONFIG; + } + } + + return E1000_SUCCESS; +} + +/*************************************************************************** + * + * Release software semaphore FLAG bit (SWFLAG). + * SWFLAG is used to synchronize the access to all shared resource between + * SW, FW and HW. + * + * hw: Struct containing variables accessed by shared code + * + ***************************************************************************/ +static void +e1000_release_software_flag(struct e1000_hw *hw) +{ + uint32_t extcnf_ctrl; + + DEBUGFUNC("e1000_release_software_flag"); + + if (hw->mac_type == e1000_ich8lan) { + extcnf_ctrl= E1000_READ_REG(hw, EXTCNF_CTRL); + extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG; + E1000_WRITE_REG(hw, EXTCNF_CTRL, extcnf_ctrl); + } + + return; +} + +/****************************************************************************** + * Reads a 16 bit word or words from the EEPROM using the ICH8's flash access + * register. + * + * hw - Struct containing variables accessed by shared code + * offset - offset of word in the EEPROM to read + * data - word read from the EEPROM + * words - number of words to read + *****************************************************************************/ +static int32_t +e1000_read_eeprom_ich8(struct e1000_hw *hw, uint16_t offset, uint16_t words, + uint16_t *data) +{ + int32_t error = E1000_SUCCESS; + uint32_t flash_bank = 0; + uint32_t act_offset = 0; + uint32_t bank_offset = 0; + uint16_t word = 0; + uint16_t i = 0; + + /* We need to know which is the valid flash bank. In the event + * that we didn't allocate eeprom_shadow_ram, we may not be + * managing flash_bank. So it cannot be trusted and needs + * to be updated with each read. + */ + /* Value of bit 22 corresponds to the flash bank we're on. */ + flash_bank = (E1000_READ_REG(hw, EECD) & E1000_EECD_SEC1VAL) ? 1 : 0; + + /* Adjust offset appropriately if we're on bank 1 - adjust for word size */ + bank_offset = flash_bank * (hw->flash_bank_size * 2); + + error = e1000_get_software_flag(hw); + if (error != E1000_SUCCESS) + return error; + + for (i = 0; i < words; i++) { + if (hw->eeprom_shadow_ram != NULL && + hw->eeprom_shadow_ram[offset+i].modified == TRUE) { + data[i] = hw->eeprom_shadow_ram[offset+i].eeprom_word; + } else { + /* The NVM part needs a byte offset, hence * 2 */ + act_offset = bank_offset + ((offset + i) * 2); + error = e1000_read_ich8_word(hw, act_offset, &word); + if (error != E1000_SUCCESS) + break; + data[i] = word; + } + } + + e1000_release_software_flag(hw); + + return error; +} + +/****************************************************************************** + * Writes a 16 bit word or words to the EEPROM using the ICH8's flash access + * register. Actually, writes are written to the shadow ram cache in the hw + * structure hw->e1000_shadow_ram. e1000_commit_shadow_ram flushes this to + * the NVM, which occurs when the NVM checksum is updated. + * + * hw - Struct containing variables accessed by shared code + * offset - offset of word in the EEPROM to write + * words - number of words to write + * data - words to write to the EEPROM + *****************************************************************************/ +static int32_t +e1000_write_eeprom_ich8(struct e1000_hw *hw, uint16_t offset, uint16_t words, + uint16_t *data) +{ + uint32_t i = 0; + int32_t error = E1000_SUCCESS; + + error = e1000_get_software_flag(hw); + if (error != E1000_SUCCESS) + return error; + + /* A driver can write to the NVM only if it has eeprom_shadow_ram + * allocated. Subsequent reads to the modified words are read from + * this cached structure as well. Writes will only go into this + * cached structure unless it's followed by a call to + * e1000_update_eeprom_checksum() where it will commit the changes + * and clear the "modified" field. + */ + if (hw->eeprom_shadow_ram != NULL) { + for (i = 0; i < words; i++) { + if ((offset + i) < E1000_SHADOW_RAM_WORDS) { + hw->eeprom_shadow_ram[offset+i].modified = TRUE; + hw->eeprom_shadow_ram[offset+i].eeprom_word = data[i]; + } else { + error = -E1000_ERR_EEPROM; + break; + } + } + } else { + /* Drivers have the option to not allocate eeprom_shadow_ram as long + * as they don't perform any NVM writes. An attempt in doing so + * will result in this error. + */ + error = -E1000_ERR_EEPROM; + } + + e1000_release_software_flag(hw); + + return error; +} + +/****************************************************************************** + * This function does initial flash setup so that a new read/write/erase cycle + * can be started. + * + * hw - The pointer to the hw structure + ****************************************************************************/ +static int32_t +e1000_ich8_cycle_init(struct e1000_hw *hw) +{ + union ich8_hws_flash_status hsfsts; + int32_t error = E1000_ERR_EEPROM; + int32_t i = 0; + + DEBUGFUNC("e1000_ich8_cycle_init"); + + hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS); + + /* May be check the Flash Des Valid bit in Hw status */ + if (hsfsts.hsf_status.fldesvalid == 0) { + DEBUGOUT("Flash descriptor invalid. SW Sequencing must be used."); + return error; + } + + /* Clear FCERR in Hw status by writing 1 */ + /* Clear DAEL in Hw status by writing a 1 */ + hsfsts.hsf_status.flcerr = 1; + hsfsts.hsf_status.dael = 1; + + E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval); + + /* Either we should have a hardware SPI cycle in progress bit to check + * against, in order to start a new cycle or FDONE bit should be changed + * in the hardware so that it is 1 after harware reset, which can then be + * used as an indication whether a cycle is in progress or has been + * completed .. we should also have some software semaphore mechanism to + * guard FDONE or the cycle in progress bit so that two threads access to + * those bits can be sequentiallized or a way so that 2 threads dont + * start the cycle at the same time */ + + if (hsfsts.hsf_status.flcinprog == 0) { + /* There is no cycle running at present, so we can start a cycle */ + /* Begin by setting Flash Cycle Done. */ + hsfsts.hsf_status.flcdone = 1; + E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval); + error = E1000_SUCCESS; + } else { + /* otherwise poll for sometime so the current cycle has a chance + * to end before giving up. */ + for (i = 0; i < ICH_FLASH_COMMAND_TIMEOUT; i++) { + hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcinprog == 0) { + error = E1000_SUCCESS; + break; + } + udelay(1); + } + if (error == E1000_SUCCESS) { + /* Successful in waiting for previous cycle to timeout, + * now set the Flash Cycle Done. */ + hsfsts.hsf_status.flcdone = 1; + E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval); + } else { + DEBUGOUT("Flash controller busy, cannot get access"); + } + } + return error; +} + +/****************************************************************************** + * This function starts a flash cycle and waits for its completion + * + * hw - The pointer to the hw structure + ****************************************************************************/ +static int32_t +e1000_ich8_flash_cycle(struct e1000_hw *hw, uint32_t timeout) +{ + union ich8_hws_flash_ctrl hsflctl; + union ich8_hws_flash_status hsfsts; + int32_t error = E1000_ERR_EEPROM; + uint32_t i = 0; + + /* Start a cycle by writing 1 in Flash Cycle Go in Hw Flash Control */ + hsflctl.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL); + hsflctl.hsf_ctrl.flcgo = 1; + E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval); + + /* wait till FDONE bit is set to 1 */ + do { + hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcdone == 1) + break; + udelay(1); + i++; + } while (i < timeout); + if (hsfsts.hsf_status.flcdone == 1 && hsfsts.hsf_status.flcerr == 0) { + error = E1000_SUCCESS; + } + return error; +} + +/****************************************************************************** + * Reads a byte or word from the NVM using the ICH8 flash access registers. + * + * hw - The pointer to the hw structure + * index - The index of the byte or word to read. + * size - Size of data to read, 1=byte 2=word + * data - Pointer to the word to store the value read. + *****************************************************************************/ +static int32_t +e1000_read_ich8_data(struct e1000_hw *hw, uint32_t index, + uint32_t size, uint16_t* data) +{ + union ich8_hws_flash_status hsfsts; + union ich8_hws_flash_ctrl hsflctl; + uint32_t flash_linear_address; + uint32_t flash_data = 0; + int32_t error = -E1000_ERR_EEPROM; + int32_t count = 0; + + DEBUGFUNC("e1000_read_ich8_data"); + + if (size < 1 || size > 2 || data == NULL || + index > ICH_FLASH_LINEAR_ADDR_MASK) + return error; + + flash_linear_address = (ICH_FLASH_LINEAR_ADDR_MASK & index) + + hw->flash_base_addr; + + do { + udelay(1); + /* Steps */ + error = e1000_ich8_cycle_init(hw); + if (error != E1000_SUCCESS) + break; + + hsflctl.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL); + /* 0b/1b corresponds to 1 or 2 byte size, respectively. */ + hsflctl.hsf_ctrl.fldbcount = size - 1; + hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_READ; + E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval); + + /* Write the last 24 bits of index into Flash Linear address field in + * Flash Address */ + /* TODO: TBD maybe check the index against the size of flash */ + + E1000_WRITE_ICH_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_address); + + error = e1000_ich8_flash_cycle(hw, ICH_FLASH_COMMAND_TIMEOUT); + + /* Check if FCERR is set to 1, if set to 1, clear it and try the whole + * sequence a few more times, else read in (shift in) the Flash Data0, + * the order is least significant byte first msb to lsb */ + if (error == E1000_SUCCESS) { + flash_data = E1000_READ_ICH_FLASH_REG(hw, ICH_FLASH_FDATA0); + if (size == 1) { + *data = (uint8_t)(flash_data & 0x000000FF); + } else if (size == 2) { + *data = (uint16_t)(flash_data & 0x0000FFFF); + } + break; + } else { + /* If we've gotten here, then things are probably completely hosed, + * but if the error condition is detected, it won't hurt to give + * it another try...ICH_FLASH_CYCLE_REPEAT_COUNT times. + */ + hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcerr == 1) { + /* Repeat for some time before giving up. */ + continue; + } else if (hsfsts.hsf_status.flcdone == 0) { + DEBUGOUT("Timeout error - flash cycle did not complete."); + break; + } + } + } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT); + + return error; +} + +/****************************************************************************** + * Writes One /two bytes to the NVM using the ICH8 flash access registers. + * + * hw - The pointer to the hw structure + * index - The index of the byte/word to read. + * size - Size of data to read, 1=byte 2=word + * data - The byte(s) to write to the NVM. + *****************************************************************************/ +static int32_t +e1000_write_ich8_data(struct e1000_hw *hw, uint32_t index, uint32_t size, + uint16_t data) +{ + union ich8_hws_flash_status hsfsts; + union ich8_hws_flash_ctrl hsflctl; + uint32_t flash_linear_address; + uint32_t flash_data = 0; + int32_t error = -E1000_ERR_EEPROM; + int32_t count = 0; + + DEBUGFUNC("e1000_write_ich8_data"); + + if (size < 1 || size > 2 || data > size * 0xff || + index > ICH_FLASH_LINEAR_ADDR_MASK) + return error; + + flash_linear_address = (ICH_FLASH_LINEAR_ADDR_MASK & index) + + hw->flash_base_addr; + + do { + udelay(1); + /* Steps */ + error = e1000_ich8_cycle_init(hw); + if (error != E1000_SUCCESS) + break; + + hsflctl.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL); + /* 0b/1b corresponds to 1 or 2 byte size, respectively. */ + hsflctl.hsf_ctrl.fldbcount = size -1; + hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_WRITE; + E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval); + + /* Write the last 24 bits of index into Flash Linear address field in + * Flash Address */ + E1000_WRITE_ICH_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_address); + + if (size == 1) + flash_data = (uint32_t)data & 0x00FF; + else + flash_data = (uint32_t)data; + + E1000_WRITE_ICH_FLASH_REG(hw, ICH_FLASH_FDATA0, flash_data); + + /* check if FCERR is set to 1 , if set to 1, clear it and try the whole + * sequence a few more times else done */ + error = e1000_ich8_flash_cycle(hw, ICH_FLASH_COMMAND_TIMEOUT); + if (error == E1000_SUCCESS) { + break; + } else { + /* If we're here, then things are most likely completely hosed, + * but if the error condition is detected, it won't hurt to give + * it another try...ICH_FLASH_CYCLE_REPEAT_COUNT times. + */ + hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcerr == 1) { + /* Repeat for some time before giving up. */ + continue; + } else if (hsfsts.hsf_status.flcdone == 0) { + DEBUGOUT("Timeout error - flash cycle did not complete."); + break; + } + } + } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT); + + return error; +} + +/****************************************************************************** + * Reads a single byte from the NVM using the ICH8 flash access registers. + * + * hw - pointer to e1000_hw structure + * index - The index of the byte to read. + * data - Pointer to a byte to store the value read. + *****************************************************************************/ +static int32_t +e1000_read_ich8_byte(struct e1000_hw *hw, uint32_t index, uint8_t* data) +{ + int32_t status = E1000_SUCCESS; + uint16_t word = 0; + + status = e1000_read_ich8_data(hw, index, 1, &word); + if (status == E1000_SUCCESS) { + *data = (uint8_t)word; + } + + return status; +} + +/****************************************************************************** + * Writes a single byte to the NVM using the ICH8 flash access registers. + * Performs verification by reading back the value and then going through + * a retry algorithm before giving up. + * + * hw - pointer to e1000_hw structure + * index - The index of the byte to write. + * byte - The byte to write to the NVM. + *****************************************************************************/ +static int32_t +e1000_verify_write_ich8_byte(struct e1000_hw *hw, uint32_t index, uint8_t byte) +{ + int32_t error = E1000_SUCCESS; + int32_t program_retries = 0; + + DEBUGOUT2("Byte := %2.2X Offset := %d\n", byte, index); + + error = e1000_write_ich8_byte(hw, index, byte); + + if (error != E1000_SUCCESS) { + for (program_retries = 0; program_retries < 100; program_retries++) { + DEBUGOUT2("Retrying \t Byte := %2.2X Offset := %d\n", byte, index); + error = e1000_write_ich8_byte(hw, index, byte); + udelay(100); + if (error == E1000_SUCCESS) + break; + } + } + + if (program_retries == 100) + error = E1000_ERR_EEPROM; + + return error; +} + +/****************************************************************************** + * Writes a single byte to the NVM using the ICH8 flash access registers. + * + * hw - pointer to e1000_hw structure + * index - The index of the byte to read. + * data - The byte to write to the NVM. + *****************************************************************************/ +static int32_t +e1000_write_ich8_byte(struct e1000_hw *hw, uint32_t index, uint8_t data) +{ + int32_t status = E1000_SUCCESS; + uint16_t word = (uint16_t)data; + + status = e1000_write_ich8_data(hw, index, 1, word); + + return status; +} + +/****************************************************************************** + * Reads a word from the NVM using the ICH8 flash access registers. + * + * hw - pointer to e1000_hw structure + * index - The starting byte index of the word to read. + * data - Pointer to a word to store the value read. + *****************************************************************************/ +static int32_t +e1000_read_ich8_word(struct e1000_hw *hw, uint32_t index, uint16_t *data) +{ + int32_t status = E1000_SUCCESS; + status = e1000_read_ich8_data(hw, index, 2, data); + return status; +} + +/****************************************************************************** + * Erases the bank specified. Each bank may be a 4, 8 or 64k block. Banks are 0 + * based. + * + * hw - pointer to e1000_hw structure + * bank - 0 for first bank, 1 for second bank + * + * Note that this function may actually erase as much as 8 or 64 KBytes. The + * amount of NVM used in each bank is a *minimum* of 4 KBytes, but in fact the + * bank size may be 4, 8 or 64 KBytes + *****************************************************************************/ +static int32_t +e1000_erase_ich8_4k_segment(struct e1000_hw *hw, uint32_t bank) +{ + union ich8_hws_flash_status hsfsts; + union ich8_hws_flash_ctrl hsflctl; + uint32_t flash_linear_address; + int32_t count = 0; + int32_t error = E1000_ERR_EEPROM; + int32_t iteration; + int32_t sub_sector_size = 0; + int32_t bank_size; + int32_t j = 0; + int32_t error_flag = 0; + + hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS); + + /* Determine HW Sector size: Read BERASE bits of Hw flash Status register */ + /* 00: The Hw sector is 256 bytes, hence we need to erase 16 + * consecutive sectors. The start index for the nth Hw sector can be + * calculated as bank * 4096 + n * 256 + * 01: The Hw sector is 4K bytes, hence we need to erase 1 sector. + * The start index for the nth Hw sector can be calculated + * as bank * 4096 + * 10: The HW sector is 8K bytes + * 11: The Hw sector size is 64K bytes */ + if (hsfsts.hsf_status.berasesz == 0x0) { + /* Hw sector size 256 */ + sub_sector_size = ICH_FLASH_SEG_SIZE_256; + bank_size = ICH_FLASH_SECTOR_SIZE; + iteration = ICH_FLASH_SECTOR_SIZE / ICH_FLASH_SEG_SIZE_256; + } else if (hsfsts.hsf_status.berasesz == 0x1) { + bank_size = ICH_FLASH_SEG_SIZE_4K; + iteration = 1; + } else if (hsfsts.hsf_status.berasesz == 0x3) { + bank_size = ICH_FLASH_SEG_SIZE_64K; + iteration = 1; + } else { + return error; + } + + for (j = 0; j < iteration ; j++) { + do { + count++; + /* Steps */ + error = e1000_ich8_cycle_init(hw); + if (error != E1000_SUCCESS) { + error_flag = 1; + break; + } + + /* Write a value 11 (block Erase) in Flash Cycle field in Hw flash + * Control */ + hsflctl.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL); + hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_ERASE; + E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval); + + /* Write the last 24 bits of an index within the block into Flash + * Linear address field in Flash Address. This probably needs to + * be calculated here based off the on-chip erase sector size and + * the software bank size (4, 8 or 64 KBytes) */ + flash_linear_address = bank * bank_size + j * sub_sector_size; + flash_linear_address += hw->flash_base_addr; + flash_linear_address &= ICH_FLASH_LINEAR_ADDR_MASK; + + E1000_WRITE_ICH_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_address); + + error = e1000_ich8_flash_cycle(hw, ICH_FLASH_ERASE_TIMEOUT); + /* Check if FCERR is set to 1. If 1, clear it and try the whole + * sequence a few more times else Done */ + if (error == E1000_SUCCESS) { + break; + } else { + hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcerr == 1) { + /* repeat for some time before giving up */ + continue; + } else if (hsfsts.hsf_status.flcdone == 0) { + error_flag = 1; + break; + } + } + } while ((count < ICH_FLASH_CYCLE_REPEAT_COUNT) && !error_flag); + if (error_flag == 1) + break; + } + if (error_flag != 1) + error = E1000_SUCCESS; + return error; +} + +static int32_t +e1000_init_lcd_from_nvm_config_region(struct e1000_hw *hw, + uint32_t cnf_base_addr, uint32_t cnf_size) +{ + uint32_t ret_val = E1000_SUCCESS; + uint16_t word_addr, reg_data, reg_addr; + uint16_t i; + + /* cnf_base_addr is in DWORD */ + word_addr = (uint16_t)(cnf_base_addr << 1); + + /* cnf_size is returned in size of dwords */ + for (i = 0; i < cnf_size; i++) { + ret_val = e1000_read_eeprom(hw, (word_addr + i*2), 1, ®_data); + if (ret_val) + return ret_val; + + ret_val = e1000_read_eeprom(hw, (word_addr + i*2 + 1), 1, ®_addr); + if (ret_val) + return ret_val; + + ret_val = e1000_get_software_flag(hw); + if (ret_val != E1000_SUCCESS) + return ret_val; + + ret_val = e1000_write_phy_reg_ex(hw, (uint32_t)reg_addr, reg_data); + + e1000_release_software_flag(hw); + } + + return ret_val; +} + + +/****************************************************************************** + * This function initializes the PHY from the NVM on ICH8 platforms. This + * is needed due to an issue where the NVM configuration is not properly + * autoloaded after power transitions. Therefore, after each PHY reset, we + * will load the configuration data out of the NVM manually. + * + * hw: Struct containing variables accessed by shared code + *****************************************************************************/ +static int32_t +e1000_init_lcd_from_nvm(struct e1000_hw *hw) +{ + uint32_t reg_data, cnf_base_addr, cnf_size, ret_val, loop; + + if (hw->phy_type != e1000_phy_igp_3) + return E1000_SUCCESS; + + /* Check if SW needs configure the PHY */ + reg_data = E1000_READ_REG(hw, FEXTNVM); + if (!(reg_data & FEXTNVM_SW_CONFIG)) + return E1000_SUCCESS; + + /* Wait for basic configuration completes before proceeding*/ + loop = 0; + do { + reg_data = E1000_READ_REG(hw, STATUS) & E1000_STATUS_LAN_INIT_DONE; + udelay(100); + loop++; + } while ((!reg_data) && (loop < 50)); + + /* Clear the Init Done bit for the next init event */ + reg_data = E1000_READ_REG(hw, STATUS); + reg_data &= ~E1000_STATUS_LAN_INIT_DONE; + E1000_WRITE_REG(hw, STATUS, reg_data); + + /* Make sure HW does not configure LCD from PHY extended configuration + before SW configuration */ + reg_data = E1000_READ_REG(hw, EXTCNF_CTRL); + if ((reg_data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE) == 0x0000) { + reg_data = E1000_READ_REG(hw, EXTCNF_SIZE); + cnf_size = reg_data & E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH; + cnf_size >>= 16; + if (cnf_size) { + reg_data = E1000_READ_REG(hw, EXTCNF_CTRL); + cnf_base_addr = reg_data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER; + /* cnf_base_addr is in DWORD */ + cnf_base_addr >>= 16; + + /* Configure LCD from extended configuration region. */ + ret_val = e1000_init_lcd_from_nvm_config_region(hw, cnf_base_addr, + cnf_size); + if (ret_val) + return ret_val; + } + } + + return E1000_SUCCESS; +} + diff -Nur ethercat-1.4.0/devices/e1000/e1000_hw-2.6.32-ethercat.h ethercat-1.4.0.patched//devices/e1000/e1000_hw-2.6.32-ethercat.h --- ethercat-1.4.0/devices/e1000/e1000_hw-2.6.32-ethercat.h 1970-01-01 01:00:00.000000000 +0100 +++ ethercat-1.4.0.patched//devices/e1000/e1000_hw-2.6.32-ethercat.h 2011-11-18 14:48:21.698942569 +0100 @@ -0,0 +1,3408 @@ +/******************************************************************************* + + Intel PRO/1000 Linux driver + Copyright(c) 1999 - 2006 Intel Corporation. + + This program is free software; you can redistribute it and/or modify it + under the terms and conditions of the GNU General Public License, + version 2, as published by the Free Software Foundation. + + This program is distributed in the hope it will be useful, but WITHOUT + ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + more details. + + You should have received a copy of the GNU General Public License along with + this program; if not, write to the Free Software Foundation, Inc., + 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. + + The full GNU General Public License is included in this distribution in + the file called "COPYING". + + Contact Information: + Linux NICS + e1000-devel Mailing List + Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 + +*******************************************************************************/ + +/* e1000_hw.h + * Structures, enums, and macros for the MAC + */ + +#ifndef _E1000_HW_H_ +#define _E1000_HW_H_ + +#include "e1000_osdep-2.6.32-ethercat.h" + + +/* Forward declarations of structures used by the shared code */ +struct e1000_hw; +struct e1000_hw_stats; + +/* Enumerated types specific to the e1000 hardware */ +/* Media Access Controlers */ +typedef enum { + e1000_undefined = 0, + e1000_82542_rev2_0, + e1000_82542_rev2_1, + e1000_82543, + e1000_82544, + e1000_82540, + e1000_82545, + e1000_82545_rev_3, + e1000_82546, + e1000_82546_rev_3, + e1000_82541, + e1000_82541_rev_2, + e1000_82547, + e1000_82547_rev_2, + e1000_82571, + e1000_82572, + e1000_82573, + e1000_80003es2lan, + e1000_ich8lan, + e1000_num_macs +} e1000_mac_type; + +typedef enum { + e1000_eeprom_uninitialized = 0, + e1000_eeprom_spi, + e1000_eeprom_microwire, + e1000_eeprom_flash, + e1000_eeprom_ich8, + e1000_eeprom_none, /* No NVM support */ + e1000_num_eeprom_types +} e1000_eeprom_type; + +/* Media Types */ +typedef enum { + e1000_media_type_copper = 0, + e1000_media_type_fiber = 1, + e1000_media_type_internal_serdes = 2, + e1000_num_media_types +} e1000_media_type; + +typedef enum { + e1000_10_half = 0, + e1000_10_full = 1, + e1000_100_half = 2, + e1000_100_full = 3 +} e1000_speed_duplex_type; + +/* Flow Control Settings */ +typedef enum { + E1000_FC_NONE = 0, + E1000_FC_RX_PAUSE = 1, + E1000_FC_TX_PAUSE = 2, + E1000_FC_FULL = 3, + E1000_FC_DEFAULT = 0xFF +} e1000_fc_type; + +struct e1000_shadow_ram { + uint16_t eeprom_word; + boolean_t modified; +}; + +/* PCI bus types */ +typedef enum { + e1000_bus_type_unknown = 0, + e1000_bus_type_pci, + e1000_bus_type_pcix, + e1000_bus_type_pci_express, + e1000_bus_type_reserved +} e1000_bus_type; + +/* PCI bus speeds */ +typedef enum { + e1000_bus_speed_unknown = 0, + e1000_bus_speed_33, + e1000_bus_speed_66, + e1000_bus_speed_100, + e1000_bus_speed_120, + e1000_bus_speed_133, + e1000_bus_speed_2500, + e1000_bus_speed_reserved +} e1000_bus_speed; + +/* PCI bus widths */ +typedef enum { + e1000_bus_width_unknown = 0, + /* These PCIe values should literally match the possible return values + * from config space */ + e1000_bus_width_pciex_1 = 1, + e1000_bus_width_pciex_2 = 2, + e1000_bus_width_pciex_4 = 4, + e1000_bus_width_32, + e1000_bus_width_64, + e1000_bus_width_reserved +} e1000_bus_width; + +/* PHY status info structure and supporting enums */ +typedef enum { + e1000_cable_length_50 = 0, + e1000_cable_length_50_80, + e1000_cable_length_80_110, + e1000_cable_length_110_140, + e1000_cable_length_140, + e1000_cable_length_undefined = 0xFF +} e1000_cable_length; + +typedef enum { + e1000_gg_cable_length_60 = 0, + e1000_gg_cable_length_60_115 = 1, + e1000_gg_cable_length_115_150 = 2, + e1000_gg_cable_length_150 = 4 +} e1000_gg_cable_length; + +typedef enum { + e1000_igp_cable_length_10 = 10, + e1000_igp_cable_length_20 = 20, + e1000_igp_cable_length_30 = 30, + e1000_igp_cable_length_40 = 40, + e1000_igp_cable_length_50 = 50, + e1000_igp_cable_length_60 = 60, + e1000_igp_cable_length_70 = 70, + e1000_igp_cable_length_80 = 80, + e1000_igp_cable_length_90 = 90, + e1000_igp_cable_length_100 = 100, + e1000_igp_cable_length_110 = 110, + e1000_igp_cable_length_115 = 115, + e1000_igp_cable_length_120 = 120, + e1000_igp_cable_length_130 = 130, + e1000_igp_cable_length_140 = 140, + e1000_igp_cable_length_150 = 150, + e1000_igp_cable_length_160 = 160, + e1000_igp_cable_length_170 = 170, + e1000_igp_cable_length_180 = 180 +} e1000_igp_cable_length; + +typedef enum { + e1000_10bt_ext_dist_enable_normal = 0, + e1000_10bt_ext_dist_enable_lower, + e1000_10bt_ext_dist_enable_undefined = 0xFF +} e1000_10bt_ext_dist_enable; + +typedef enum { + e1000_rev_polarity_normal = 0, + e1000_rev_polarity_reversed, + e1000_rev_polarity_undefined = 0xFF +} e1000_rev_polarity; + +typedef enum { + e1000_downshift_normal = 0, + e1000_downshift_activated, + e1000_downshift_undefined = 0xFF +} e1000_downshift; + +typedef enum { + e1000_smart_speed_default = 0, + e1000_smart_speed_on, + e1000_smart_speed_off +} e1000_smart_speed; + +typedef enum { + e1000_polarity_reversal_enabled = 0, + e1000_polarity_reversal_disabled, + e1000_polarity_reversal_undefined = 0xFF +} e1000_polarity_reversal; + +typedef enum { + e1000_auto_x_mode_manual_mdi = 0, + e1000_auto_x_mode_manual_mdix, + e1000_auto_x_mode_auto1, + e1000_auto_x_mode_auto2, + e1000_auto_x_mode_undefined = 0xFF +} e1000_auto_x_mode; + +typedef enum { + e1000_1000t_rx_status_not_ok = 0, + e1000_1000t_rx_status_ok, + e1000_1000t_rx_status_undefined = 0xFF +} e1000_1000t_rx_status; + +typedef enum { + e1000_phy_m88 = 0, + e1000_phy_igp, + e1000_phy_igp_2, + e1000_phy_gg82563, + e1000_phy_igp_3, + e1000_phy_ife, + e1000_phy_undefined = 0xFF +} e1000_phy_type; + +typedef enum { + e1000_ms_hw_default = 0, + e1000_ms_force_master, + e1000_ms_force_slave, + e1000_ms_auto +} e1000_ms_type; + +typedef enum { + e1000_ffe_config_enabled = 0, + e1000_ffe_config_active, + e1000_ffe_config_blocked +} e1000_ffe_config; + +typedef enum { + e1000_dsp_config_disabled = 0, + e1000_dsp_config_enabled, + e1000_dsp_config_activated, + e1000_dsp_config_undefined = 0xFF +} e1000_dsp_config; + +struct e1000_phy_info { + e1000_cable_length cable_length; + e1000_10bt_ext_dist_enable extended_10bt_distance; + e1000_rev_polarity cable_polarity; + e1000_downshift downshift; + e1000_polarity_reversal polarity_correction; + e1000_auto_x_mode mdix_mode; + e1000_1000t_rx_status local_rx; + e1000_1000t_rx_status remote_rx; +}; + +struct e1000_phy_stats { + uint32_t idle_errors; + uint32_t receive_errors; +}; + +struct e1000_eeprom_info { + e1000_eeprom_type type; + uint16_t word_size; + uint16_t opcode_bits; + uint16_t address_bits; + uint16_t delay_usec; + uint16_t page_size; + boolean_t use_eerd; + boolean_t use_eewr; +}; + +/* Flex ASF Information */ +#define E1000_HOST_IF_MAX_SIZE 2048 + +typedef enum { + e1000_byte_align = 0, + e1000_word_align = 1, + e1000_dword_align = 2 +} e1000_align_type; + + + +/* Error Codes */ +#define E1000_SUCCESS 0 +#define E1000_ERR_EEPROM 1 +#define E1000_ERR_PHY 2 +#define E1000_ERR_CONFIG 3 +#define E1000_ERR_PARAM 4 +#define E1000_ERR_MAC_TYPE 5 +#define E1000_ERR_PHY_TYPE 6 +#define E1000_ERR_RESET 9 +#define E1000_ERR_MASTER_REQUESTS_PENDING 10 +#define E1000_ERR_HOST_INTERFACE_COMMAND 11 +#define E1000_BLK_PHY_RESET 12 +#define E1000_ERR_SWFW_SYNC 13 + +#define E1000_BYTE_SWAP_WORD(_value) ((((_value) & 0x00ff) << 8) | \ + (((_value) & 0xff00) >> 8)) + +/* Function prototypes */ +/* Initialization */ +int32_t e1000_reset_hw(struct e1000_hw *hw); +int32_t e1000_init_hw(struct e1000_hw *hw); +int32_t e1000_set_mac_type(struct e1000_hw *hw); +void e1000_set_media_type(struct e1000_hw *hw); + +/* Link Configuration */ +int32_t e1000_setup_link(struct e1000_hw *hw); +int32_t e1000_phy_setup_autoneg(struct e1000_hw *hw); +void e1000_config_collision_dist(struct e1000_hw *hw); +int32_t e1000_check_for_link(struct e1000_hw *hw); +int32_t e1000_get_speed_and_duplex(struct e1000_hw *hw, uint16_t *speed, uint16_t *duplex); +int32_t e1000_force_mac_fc(struct e1000_hw *hw); + +/* PHY */ +int32_t e1000_read_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t *phy_data); +int32_t e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t data); +int32_t e1000_phy_hw_reset(struct e1000_hw *hw); +int32_t e1000_phy_reset(struct e1000_hw *hw); +int32_t e1000_phy_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info); +int32_t e1000_validate_mdi_setting(struct e1000_hw *hw); + +void e1000_phy_powerdown_workaround(struct e1000_hw *hw); + +/* EEPROM Functions */ +int32_t e1000_init_eeprom_params(struct e1000_hw *hw); + +/* MNG HOST IF functions */ +uint32_t e1000_enable_mng_pass_thru(struct e1000_hw *hw); + +#define E1000_MNG_DHCP_TX_PAYLOAD_CMD 64 +#define E1000_HI_MAX_MNG_DATA_LENGTH 0x6F8 /* Host Interface data length */ + +#define E1000_MNG_DHCP_COMMAND_TIMEOUT 10 /* Time in ms to process MNG command */ +#define E1000_MNG_DHCP_COOKIE_OFFSET 0x6F0 /* Cookie offset */ +#define E1000_MNG_DHCP_COOKIE_LENGTH 0x10 /* Cookie length */ +#define E1000_MNG_IAMT_MODE 0x3 +#define E1000_MNG_ICH_IAMT_MODE 0x2 +#define E1000_IAMT_SIGNATURE 0x544D4149 /* Intel(R) Active Management Technology signature */ + +#define E1000_MNG_DHCP_COOKIE_STATUS_PARSING_SUPPORT 0x1 /* DHCP parsing enabled */ +#define E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT 0x2 /* DHCP parsing enabled */ +#define E1000_VFTA_ENTRY_SHIFT 0x5 +#define E1000_VFTA_ENTRY_MASK 0x7F +#define E1000_VFTA_ENTRY_BIT_SHIFT_MASK 0x1F + +struct e1000_host_mng_command_header { + uint8_t command_id; + uint8_t checksum; + uint16_t reserved1; + uint16_t reserved2; + uint16_t command_length; +}; + +struct e1000_host_mng_command_info { + struct e1000_host_mng_command_header command_header; /* Command Head/Command Result Head has 4 bytes */ + uint8_t command_data[E1000_HI_MAX_MNG_DATA_LENGTH]; /* Command data can length 0..0x658*/ +}; +#ifdef __BIG_ENDIAN +struct e1000_host_mng_dhcp_cookie{ + uint32_t signature; + uint16_t vlan_id; + uint8_t reserved0; + uint8_t status; + uint32_t reserved1; + uint8_t checksum; + uint8_t reserved3; + uint16_t reserved2; +}; +#else +struct e1000_host_mng_dhcp_cookie{ + uint32_t signature; + uint8_t status; + uint8_t reserved0; + uint16_t vlan_id; + uint32_t reserved1; + uint16_t reserved2; + uint8_t reserved3; + uint8_t checksum; +}; +#endif + +int32_t e1000_mng_write_dhcp_info(struct e1000_hw *hw, uint8_t *buffer, + uint16_t length); +boolean_t e1000_check_mng_mode(struct e1000_hw *hw); +boolean_t e1000_enable_tx_pkt_filtering(struct e1000_hw *hw); +int32_t e1000_read_eeprom(struct e1000_hw *hw, uint16_t reg, uint16_t words, uint16_t *data); +int32_t e1000_validate_eeprom_checksum(struct e1000_hw *hw); +int32_t e1000_update_eeprom_checksum(struct e1000_hw *hw); +int32_t e1000_write_eeprom(struct e1000_hw *hw, uint16_t reg, uint16_t words, uint16_t *data); +int32_t e1000_read_mac_addr(struct e1000_hw * hw); + +/* Filters (multicast, vlan, receive) */ +uint32_t e1000_hash_mc_addr(struct e1000_hw *hw, uint8_t * mc_addr); +void e1000_mta_set(struct e1000_hw *hw, uint32_t hash_value); +void e1000_rar_set(struct e1000_hw *hw, uint8_t * mc_addr, uint32_t rar_index); +void e1000_write_vfta(struct e1000_hw *hw, uint32_t offset, uint32_t value); + +/* LED functions */ +int32_t e1000_setup_led(struct e1000_hw *hw); +int32_t e1000_cleanup_led(struct e1000_hw *hw); +int32_t e1000_led_on(struct e1000_hw *hw); +int32_t e1000_led_off(struct e1000_hw *hw); +int32_t e1000_blink_led_start(struct e1000_hw *hw); + +/* Adaptive IFS Functions */ + +/* Everything else */ +void e1000_reset_adaptive(struct e1000_hw *hw); +void e1000_update_adaptive(struct e1000_hw *hw); +void e1000_tbi_adjust_stats(struct e1000_hw *hw, struct e1000_hw_stats *stats, uint32_t frame_len, uint8_t * mac_addr); +void e1000_get_bus_info(struct e1000_hw *hw); +void e1000_pci_set_mwi(struct e1000_hw *hw); +void e1000_pci_clear_mwi(struct e1000_hw *hw); +void e1000_read_pci_cfg(struct e1000_hw *hw, uint32_t reg, uint16_t * value); +void e1000_write_pci_cfg(struct e1000_hw *hw, uint32_t reg, uint16_t * value); +int32_t e1000_read_pcie_cap_reg(struct e1000_hw *hw, uint32_t reg, uint16_t *value); +void e1000_pcix_set_mmrbc(struct e1000_hw *hw, int mmrbc); +int e1000_pcix_get_mmrbc(struct e1000_hw *hw); +/* Port I/O is only supported on 82544 and newer */ +void e1000_io_write(struct e1000_hw *hw, unsigned long port, uint32_t value); +int32_t e1000_disable_pciex_master(struct e1000_hw *hw); +int32_t e1000_check_phy_reset_block(struct e1000_hw *hw); + + +#define E1000_READ_REG_IO(a, reg) \ + e1000_read_reg_io((a), E1000_##reg) +#define E1000_WRITE_REG_IO(a, reg, val) \ + e1000_write_reg_io((a), E1000_##reg, val) + +/* PCI Device IDs */ +#define E1000_DEV_ID_82542 0x1000 +#define E1000_DEV_ID_82543GC_FIBER 0x1001 +#define E1000_DEV_ID_82543GC_COPPER 0x1004 +#define E1000_DEV_ID_82544EI_COPPER 0x1008 +#define E1000_DEV_ID_82544EI_FIBER 0x1009 +#define E1000_DEV_ID_82544GC_COPPER 0x100C +#define E1000_DEV_ID_82544GC_LOM 0x100D +#define E1000_DEV_ID_82540EM 0x100E +#define E1000_DEV_ID_82540EM_LOM 0x1015 +#define E1000_DEV_ID_82540EP_LOM 0x1016 +#define E1000_DEV_ID_82540EP 0x1017 +#define E1000_DEV_ID_82540EP_LP 0x101E +#define E1000_DEV_ID_82545EM_COPPER 0x100F +#define E1000_DEV_ID_82545EM_FIBER 0x1011 +#define E1000_DEV_ID_82545GM_COPPER 0x1026 +#define E1000_DEV_ID_82545GM_FIBER 0x1027 +#define E1000_DEV_ID_82545GM_SERDES 0x1028 +#define E1000_DEV_ID_82546EB_COPPER 0x1010 +#define E1000_DEV_ID_82546EB_FIBER 0x1012 +#define E1000_DEV_ID_82546EB_QUAD_COPPER 0x101D +#define E1000_DEV_ID_82541EI 0x1013 +#define E1000_DEV_ID_82541EI_MOBILE 0x1018 +#define E1000_DEV_ID_82541ER_LOM 0x1014 +#define E1000_DEV_ID_82541ER 0x1078 +#define E1000_DEV_ID_82547GI 0x1075 +#define E1000_DEV_ID_82541GI 0x1076 +#define E1000_DEV_ID_82541GI_MOBILE 0x1077 +#define E1000_DEV_ID_82541GI_LF 0x107C +#define E1000_DEV_ID_82546GB_COPPER 0x1079 +#define E1000_DEV_ID_82546GB_FIBER 0x107A +#define E1000_DEV_ID_82546GB_SERDES 0x107B +#define E1000_DEV_ID_82546GB_PCIE 0x108A +#define E1000_DEV_ID_82546GB_QUAD_COPPER 0x1099 +#define E1000_DEV_ID_82547EI 0x1019 +#define E1000_DEV_ID_82547EI_MOBILE 0x101A +#define E1000_DEV_ID_82571EB_COPPER 0x105E +#define E1000_DEV_ID_82571EB_FIBER 0x105F +#define E1000_DEV_ID_82571EB_SERDES 0x1060 +#define E1000_DEV_ID_82571EB_QUAD_COPPER 0x10A4 +#define E1000_DEV_ID_82571PT_QUAD_COPPER 0x10D5 +#define E1000_DEV_ID_82571EB_QUAD_FIBER 0x10A5 +#define E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE 0x10BC +#define E1000_DEV_ID_82571EB_SERDES_DUAL 0x10D9 +#define E1000_DEV_ID_82571EB_SERDES_QUAD 0x10DA +#define E1000_DEV_ID_82572EI_COPPER 0x107D +#define E1000_DEV_ID_82572EI_FIBER 0x107E +#define E1000_DEV_ID_82572EI_SERDES 0x107F +#define E1000_DEV_ID_82572EI 0x10B9 +#define E1000_DEV_ID_82573E 0x108B +#define E1000_DEV_ID_82573E_IAMT 0x108C +#define E1000_DEV_ID_82573L 0x109A +#define E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 0x10B5 +#define E1000_DEV_ID_80003ES2LAN_COPPER_DPT 0x1096 +#define E1000_DEV_ID_80003ES2LAN_SERDES_DPT 0x1098 +#define E1000_DEV_ID_80003ES2LAN_COPPER_SPT 0x10BA +#define E1000_DEV_ID_80003ES2LAN_SERDES_SPT 0x10BB + +#define E1000_DEV_ID_ICH8_IGP_M_AMT 0x1049 +#define E1000_DEV_ID_ICH8_IGP_AMT 0x104A +#define E1000_DEV_ID_ICH8_IGP_C 0x104B +#define E1000_DEV_ID_ICH8_IFE 0x104C +#define E1000_DEV_ID_ICH8_IFE_GT 0x10C4 +#define E1000_DEV_ID_ICH8_IFE_G 0x10C5 +#define E1000_DEV_ID_ICH8_IGP_M 0x104D + + +#define NODE_ADDRESS_SIZE 6 +#define ETH_LENGTH_OF_ADDRESS 6 + +/* MAC decode size is 128K - This is the size of BAR0 */ +#define MAC_DECODE_SIZE (128 * 1024) + +#define E1000_82542_2_0_REV_ID 2 +#define E1000_82542_2_1_REV_ID 3 +#define E1000_REVISION_0 0 +#define E1000_REVISION_1 1 +#define E1000_REVISION_2 2 +#define E1000_REVISION_3 3 + +#define SPEED_10 10 +#define SPEED_100 100 +#define SPEED_1000 1000 +#define HALF_DUPLEX 1 +#define FULL_DUPLEX 2 + +/* The sizes (in bytes) of a ethernet packet */ +#define ENET_HEADER_SIZE 14 +#define MAXIMUM_ETHERNET_FRAME_SIZE 1518 /* With FCS */ +#define MINIMUM_ETHERNET_FRAME_SIZE 64 /* With FCS */ +#define ETHERNET_FCS_SIZE 4 +#define MAXIMUM_ETHERNET_PACKET_SIZE \ + (MAXIMUM_ETHERNET_FRAME_SIZE - ETHERNET_FCS_SIZE) +#define MINIMUM_ETHERNET_PACKET_SIZE \ + (MINIMUM_ETHERNET_FRAME_SIZE - ETHERNET_FCS_SIZE) +#define CRC_LENGTH ETHERNET_FCS_SIZE +#define MAX_JUMBO_FRAME_SIZE 0x3F00 + + +/* 802.1q VLAN Packet Sizes */ +#define VLAN_TAG_SIZE 4 /* 802.3ac tag (not DMAed) */ + +/* Ethertype field values */ +#define ETHERNET_IEEE_VLAN_TYPE 0x8100 /* 802.3ac packet */ +#define ETHERNET_IP_TYPE 0x0800 /* IP packets */ +#define ETHERNET_ARP_TYPE 0x0806 /* Address Resolution Protocol (ARP) */ + +/* Packet Header defines */ +#define IP_PROTOCOL_TCP 6 +#define IP_PROTOCOL_UDP 0x11 + +/* This defines the bits that are set in the Interrupt Mask + * Set/Read Register. Each bit is documented below: + * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0) + * o RXSEQ = Receive Sequence Error + */ +#define POLL_IMS_ENABLE_MASK ( \ + E1000_IMS_RXDMT0 | \ + E1000_IMS_RXSEQ) + +/* This defines the bits that are set in the Interrupt Mask + * Set/Read Register. Each bit is documented below: + * o RXT0 = Receiver Timer Interrupt (ring 0) + * o TXDW = Transmit Descriptor Written Back + * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0) + * o RXSEQ = Receive Sequence Error + * o LSC = Link Status Change + */ +#define IMS_ENABLE_MASK ( \ + E1000_IMS_RXT0 | \ + E1000_IMS_TXDW | \ + E1000_IMS_RXDMT0 | \ + E1000_IMS_RXSEQ | \ + E1000_IMS_LSC) + +/* Additional interrupts need to be handled for e1000_ich8lan: + DSW = The FW changed the status of the DISSW bit in FWSM + PHYINT = The LAN connected device generates an interrupt + EPRST = Manageability reset event */ +#define IMS_ICH8LAN_ENABLE_MASK (\ + E1000_IMS_DSW | \ + E1000_IMS_PHYINT | \ + E1000_IMS_EPRST) + +/* Number of high/low register pairs in the RAR. The RAR (Receive Address + * Registers) holds the directed and multicast addresses that we monitor. We + * reserve one of these spots for our directed address, allowing us room for + * E1000_RAR_ENTRIES - 1 multicast addresses. + */ +#define E1000_RAR_ENTRIES 15 + +#define E1000_RAR_ENTRIES_ICH8LAN 6 + +#define MIN_NUMBER_OF_DESCRIPTORS 8 +#define MAX_NUMBER_OF_DESCRIPTORS 0xFFF8 + +/* Receive Descriptor */ +struct e1000_rx_desc { + uint64_t buffer_addr; /* Address of the descriptor's data buffer */ + uint16_t length; /* Length of data DMAed into data buffer */ + uint16_t csum; /* Packet checksum */ + uint8_t status; /* Descriptor status */ + uint8_t errors; /* Descriptor Errors */ + uint16_t special; +}; + +/* Receive Descriptor - Extended */ +union e1000_rx_desc_extended { + struct { + uint64_t buffer_addr; + uint64_t reserved; + } read; + struct { + struct { + uint32_t mrq; /* Multiple Rx Queues */ + union { + uint32_t rss; /* RSS Hash */ + struct { + uint16_t ip_id; /* IP id */ + uint16_t csum; /* Packet Checksum */ + } csum_ip; + } hi_dword; + } lower; + struct { + uint32_t status_error; /* ext status/error */ + uint16_t length; + uint16_t vlan; /* VLAN tag */ + } upper; + } wb; /* writeback */ +}; + +#define MAX_PS_BUFFERS 4 +/* Receive Descriptor - Packet Split */ +union e1000_rx_desc_packet_split { + struct { + /* one buffer for protocol header(s), three data buffers */ + uint64_t buffer_addr[MAX_PS_BUFFERS]; + } read; + struct { + struct { + uint32_t mrq; /* Multiple Rx Queues */ + union { + uint32_t rss; /* RSS Hash */ + struct { + uint16_t ip_id; /* IP id */ + uint16_t csum; /* Packet Checksum */ + } csum_ip; + } hi_dword; + } lower; + struct { + uint32_t status_error; /* ext status/error */ + uint16_t length0; /* length of buffer 0 */ + uint16_t vlan; /* VLAN tag */ + } middle; + struct { + uint16_t header_status; + uint16_t length[3]; /* length of buffers 1-3 */ + } upper; + uint64_t reserved; + } wb; /* writeback */ +}; + +/* Receive Decriptor bit definitions */ +#define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */ +#define E1000_RXD_STAT_EOP 0x02 /* End of Packet */ +#define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */ +#define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */ +#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum caculated */ +#define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */ +#define E1000_RXD_STAT_IPCS 0x40 /* IP xsum calculated */ +#define E1000_RXD_STAT_PIF 0x80 /* passed in-exact filter */ +#define E1000_RXD_STAT_IPIDV 0x200 /* IP identification valid */ +#define E1000_RXD_STAT_UDPV 0x400 /* Valid UDP checksum */ +#define E1000_RXD_STAT_ACK 0x8000 /* ACK Packet indication */ +#define E1000_RXD_ERR_CE 0x01 /* CRC Error */ +#define E1000_RXD_ERR_SE 0x02 /* Symbol Error */ +#define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */ +#define E1000_RXD_ERR_CXE 0x10 /* Carrier Extension Error */ +#define E1000_RXD_ERR_TCPE 0x20 /* TCP/UDP Checksum Error */ +#define E1000_RXD_ERR_IPE 0x40 /* IP Checksum Error */ +#define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */ +#define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */ +#define E1000_RXD_SPC_PRI_MASK 0xE000 /* Priority is in upper 3 bits */ +#define E1000_RXD_SPC_PRI_SHIFT 13 +#define E1000_RXD_SPC_CFI_MASK 0x1000 /* CFI is bit 12 */ +#define E1000_RXD_SPC_CFI_SHIFT 12 + +#define E1000_RXDEXT_STATERR_CE 0x01000000 +#define E1000_RXDEXT_STATERR_SE 0x02000000 +#define E1000_RXDEXT_STATERR_SEQ 0x04000000 +#define E1000_RXDEXT_STATERR_CXE 0x10000000 +#define E1000_RXDEXT_STATERR_TCPE 0x20000000 +#define E1000_RXDEXT_STATERR_IPE 0x40000000 +#define E1000_RXDEXT_STATERR_RXE 0x80000000 + +#define E1000_RXDPS_HDRSTAT_HDRSP 0x00008000 +#define E1000_RXDPS_HDRSTAT_HDRLEN_MASK 0x000003FF + +/* mask to determine if packets should be dropped due to frame errors */ +#define E1000_RXD_ERR_FRAME_ERR_MASK ( \ + E1000_RXD_ERR_CE | \ + E1000_RXD_ERR_SE | \ + E1000_RXD_ERR_SEQ | \ + E1000_RXD_ERR_CXE | \ + E1000_RXD_ERR_RXE) + + +/* Same mask, but for extended and packet split descriptors */ +#define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \ + E1000_RXDEXT_STATERR_CE | \ + E1000_RXDEXT_STATERR_SE | \ + E1000_RXDEXT_STATERR_SEQ | \ + E1000_RXDEXT_STATERR_CXE | \ + E1000_RXDEXT_STATERR_RXE) + + +/* Transmit Descriptor */ +struct e1000_tx_desc { + uint64_t buffer_addr; /* Address of the descriptor's data buffer */ + union { + uint32_t data; + struct { + uint16_t length; /* Data buffer length */ + uint8_t cso; /* Checksum offset */ + uint8_t cmd; /* Descriptor control */ + } flags; + } lower; + union { + uint32_t data; + struct { + uint8_t status; /* Descriptor status */ + uint8_t css; /* Checksum start */ + uint16_t special; + } fields; + } upper; +}; + +/* Transmit Descriptor bit definitions */ +#define E1000_TXD_DTYP_D 0x00100000 /* Data Descriptor */ +#define E1000_TXD_DTYP_C 0x00000000 /* Context Descriptor */ +#define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */ +#define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */ +#define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */ +#define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */ +#define E1000_TXD_CMD_IC 0x04000000 /* Insert Checksum */ +#define E1000_TXD_CMD_RS 0x08000000 /* Report Status */ +#define E1000_TXD_CMD_RPS 0x10000000 /* Report Packet Sent */ +#define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */ +#define E1000_TXD_CMD_VLE 0x40000000 /* Add VLAN tag */ +#define E1000_TXD_CMD_IDE 0x80000000 /* Enable Tidv register */ +#define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */ +#define E1000_TXD_STAT_EC 0x00000002 /* Excess Collisions */ +#define E1000_TXD_STAT_LC 0x00000004 /* Late Collisions */ +#define E1000_TXD_STAT_TU 0x00000008 /* Transmit underrun */ +#define E1000_TXD_CMD_TCP 0x01000000 /* TCP packet */ +#define E1000_TXD_CMD_IP 0x02000000 /* IP packet */ +#define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */ +#define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */ + +/* Offload Context Descriptor */ +struct e1000_context_desc { + union { + uint32_t ip_config; + struct { + uint8_t ipcss; /* IP checksum start */ + uint8_t ipcso; /* IP checksum offset */ + uint16_t ipcse; /* IP checksum end */ + } ip_fields; + } lower_setup; + union { + uint32_t tcp_config; + struct { + uint8_t tucss; /* TCP checksum start */ + uint8_t tucso; /* TCP checksum offset */ + uint16_t tucse; /* TCP checksum end */ + } tcp_fields; + } upper_setup; + uint32_t cmd_and_length; /* */ + union { + uint32_t data; + struct { + uint8_t status; /* Descriptor status */ + uint8_t hdr_len; /* Header length */ + uint16_t mss; /* Maximum segment size */ + } fields; + } tcp_seg_setup; +}; + +/* Offload data descriptor */ +struct e1000_data_desc { + uint64_t buffer_addr; /* Address of the descriptor's buffer address */ + union { + uint32_t data; + struct { + uint16_t length; /* Data buffer length */ + uint8_t typ_len_ext; /* */ + uint8_t cmd; /* */ + } flags; + } lower; + union { + uint32_t data; + struct { + uint8_t status; /* Descriptor status */ + uint8_t popts; /* Packet Options */ + uint16_t special; /* */ + } fields; + } upper; +}; + +/* Filters */ +#define E1000_NUM_UNICAST 16 /* Unicast filter entries */ +#define E1000_MC_TBL_SIZE 128 /* Multicast Filter Table (4096 bits) */ +#define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */ + +#define E1000_NUM_UNICAST_ICH8LAN 7 +#define E1000_MC_TBL_SIZE_ICH8LAN 32 + + +/* Receive Address Register */ +struct e1000_rar { + volatile uint32_t low; /* receive address low */ + volatile uint32_t high; /* receive address high */ +}; + +/* Number of entries in the Multicast Table Array (MTA). */ +#define E1000_NUM_MTA_REGISTERS 128 +#define E1000_NUM_MTA_REGISTERS_ICH8LAN 32 + +/* IPv4 Address Table Entry */ +struct e1000_ipv4_at_entry { + volatile uint32_t ipv4_addr; /* IP Address (RW) */ + volatile uint32_t reserved; +}; + +/* Four wakeup IP addresses are supported */ +#define E1000_WAKEUP_IP_ADDRESS_COUNT_MAX 4 +#define E1000_IP4AT_SIZE E1000_WAKEUP_IP_ADDRESS_COUNT_MAX +#define E1000_IP4AT_SIZE_ICH8LAN 3 +#define E1000_IP6AT_SIZE 1 + +/* IPv6 Address Table Entry */ +struct e1000_ipv6_at_entry { + volatile uint8_t ipv6_addr[16]; +}; + +/* Flexible Filter Length Table Entry */ +struct e1000_fflt_entry { + volatile uint32_t length; /* Flexible Filter Length (RW) */ + volatile uint32_t reserved; +}; + +/* Flexible Filter Mask Table Entry */ +struct e1000_ffmt_entry { + volatile uint32_t mask; /* Flexible Filter Mask (RW) */ + volatile uint32_t reserved; +}; + +/* Flexible Filter Value Table Entry */ +struct e1000_ffvt_entry { + volatile uint32_t value; /* Flexible Filter Value (RW) */ + volatile uint32_t reserved; +}; + +/* Four Flexible Filters are supported */ +#define E1000_FLEXIBLE_FILTER_COUNT_MAX 4 + +/* Each Flexible Filter is at most 128 (0x80) bytes in length */ +#define E1000_FLEXIBLE_FILTER_SIZE_MAX 128 + +#define E1000_FFLT_SIZE E1000_FLEXIBLE_FILTER_COUNT_MAX +#define E1000_FFMT_SIZE E1000_FLEXIBLE_FILTER_SIZE_MAX +#define E1000_FFVT_SIZE E1000_FLEXIBLE_FILTER_SIZE_MAX + +#define E1000_DISABLE_SERDES_LOOPBACK 0x0400 + +/* Register Set. (82543, 82544) + * + * Registers are defined to be 32 bits and should be accessed as 32 bit values. + * These registers are physically located on the NIC, but are mapped into the + * host memory address space. + * + * RW - register is both readable and writable + * RO - register is read only + * WO - register is write only + * R/clr - register is read only and is cleared when read + * A - register array + */ +#define E1000_CTRL 0x00000 /* Device Control - RW */ +#define E1000_CTRL_DUP 0x00004 /* Device Control Duplicate (Shadow) - RW */ +#define E1000_STATUS 0x00008 /* Device Status - RO */ +#define E1000_EECD 0x00010 /* EEPROM/Flash Control - RW */ +#define E1000_EERD 0x00014 /* EEPROM Read - RW */ +#define E1000_CTRL_EXT 0x00018 /* Extended Device Control - RW */ +#define E1000_FLA 0x0001C /* Flash Access - RW */ +#define E1000_MDIC 0x00020 /* MDI Control - RW */ +#define E1000_SCTL 0x00024 /* SerDes Control - RW */ +#define E1000_FEXTNVM 0x00028 /* Future Extended NVM register */ +#define E1000_FCAL 0x00028 /* Flow Control Address Low - RW */ +#define E1000_FCAH 0x0002C /* Flow Control Address High -RW */ +#define E1000_FCT 0x00030 /* Flow Control Type - RW */ +#define E1000_VET 0x00038 /* VLAN Ether Type - RW */ +#define E1000_ICR 0x000C0 /* Interrupt Cause Read - R/clr */ +#define E1000_ITR 0x000C4 /* Interrupt Throttling Rate - RW */ +#define E1000_ICS 0x000C8 /* Interrupt Cause Set - WO */ +#define E1000_IMS 0x000D0 /* Interrupt Mask Set - RW */ +#define E1000_IMC 0x000D8 /* Interrupt Mask Clear - WO */ +#define E1000_IAM 0x000E0 /* Interrupt Acknowledge Auto Mask */ +#define E1000_RCTL 0x00100 /* RX Control - RW */ +#define E1000_RDTR1 0x02820 /* RX Delay Timer (1) - RW */ +#define E1000_RDBAL1 0x02900 /* RX Descriptor Base Address Low (1) - RW */ +#define E1000_RDBAH1 0x02904 /* RX Descriptor Base Address High (1) - RW */ +#define E1000_RDLEN1 0x02908 /* RX Descriptor Length (1) - RW */ +#define E1000_RDH1 0x02910 /* RX Descriptor Head (1) - RW */ +#define E1000_RDT1 0x02918 /* RX Descriptor Tail (1) - RW */ +#define E1000_FCTTV 0x00170 /* Flow Control Transmit Timer Value - RW */ +#define E1000_TXCW 0x00178 /* TX Configuration Word - RW */ +#define E1000_RXCW 0x00180 /* RX Configuration Word - RO */ +#define E1000_TCTL 0x00400 /* TX Control - RW */ +#define E1000_TCTL_EXT 0x00404 /* Extended TX Control - RW */ +#define E1000_TIPG 0x00410 /* TX Inter-packet gap -RW */ +#define E1000_TBT 0x00448 /* TX Burst Timer - RW */ +#define E1000_AIT 0x00458 /* Adaptive Interframe Spacing Throttle - RW */ +#define E1000_LEDCTL 0x00E00 /* LED Control - RW */ +#define E1000_EXTCNF_CTRL 0x00F00 /* Extended Configuration Control */ +#define E1000_EXTCNF_SIZE 0x00F08 /* Extended Configuration Size */ +#define E1000_PHY_CTRL 0x00F10 /* PHY Control Register in CSR */ +#define FEXTNVM_SW_CONFIG 0x0001 +#define E1000_PBA 0x01000 /* Packet Buffer Allocation - RW */ +#define E1000_PBS 0x01008 /* Packet Buffer Size */ +#define E1000_EEMNGCTL 0x01010 /* MNG EEprom Control */ +#define E1000_FLASH_UPDATES 1000 +#define E1000_EEARBC 0x01024 /* EEPROM Auto Read Bus Control */ +#define E1000_FLASHT 0x01028 /* FLASH Timer Register */ +#define E1000_EEWR 0x0102C /* EEPROM Write Register - RW */ +#define E1000_FLSWCTL 0x01030 /* FLASH control register */ +#define E1000_FLSWDATA 0x01034 /* FLASH data register */ +#define E1000_FLSWCNT 0x01038 /* FLASH Access Counter */ +#define E1000_FLOP 0x0103C /* FLASH Opcode Register */ +#define E1000_ERT 0x02008 /* Early Rx Threshold - RW */ +#define E1000_FCRTL 0x02160 /* Flow Control Receive Threshold Low - RW */ +#define E1000_FCRTH 0x02168 /* Flow Control Receive Threshold High - RW */ +#define E1000_PSRCTL 0x02170 /* Packet Split Receive Control - RW */ +#define E1000_RDBAL 0x02800 /* RX Descriptor Base Address Low - RW */ +#define E1000_RDBAH 0x02804 /* RX Descriptor Base Address High - RW */ +#define E1000_RDLEN 0x02808 /* RX Descriptor Length - RW */ +#define E1000_RDH 0x02810 /* RX Descriptor Head - RW */ +#define E1000_RDT 0x02818 /* RX Descriptor Tail - RW */ +#define E1000_RDTR 0x02820 /* RX Delay Timer - RW */ +#define E1000_RDBAL0 E1000_RDBAL /* RX Desc Base Address Low (0) - RW */ +#define E1000_RDBAH0 E1000_RDBAH /* RX Desc Base Address High (0) - RW */ +#define E1000_RDLEN0 E1000_RDLEN /* RX Desc Length (0) - RW */ +#define E1000_RDH0 E1000_RDH /* RX Desc Head (0) - RW */ +#define E1000_RDT0 E1000_RDT /* RX Desc Tail (0) - RW */ +#define E1000_RDTR0 E1000_RDTR /* RX Delay Timer (0) - RW */ +#define E1000_RXDCTL 0x02828 /* RX Descriptor Control queue 0 - RW */ +#define E1000_RXDCTL1 0x02928 /* RX Descriptor Control queue 1 - RW */ +#define E1000_RADV 0x0282C /* RX Interrupt Absolute Delay Timer - RW */ +#define E1000_RSRPD 0x02C00 /* RX Small Packet Detect - RW */ +#define E1000_RAID 0x02C08 /* Receive Ack Interrupt Delay - RW */ +#define E1000_TXDMAC 0x03000 /* TX DMA Control - RW */ +#define E1000_KABGTXD 0x03004 /* AFE Band Gap Transmit Ref Data */ +#define E1000_TDFH 0x03410 /* TX Data FIFO Head - RW */ +#define E1000_TDFT 0x03418 /* TX Data FIFO Tail - RW */ +#define E1000_TDFHS 0x03420 /* TX Data FIFO Head Saved - RW */ +#define E1000_TDFTS 0x03428 /* TX Data FIFO Tail Saved - RW */ +#define E1000_TDFPC 0x03430 /* TX Data FIFO Packet Count - RW */ +#define E1000_TDBAL 0x03800 /* TX Descriptor Base Address Low - RW */ +#define E1000_TDBAH 0x03804 /* TX Descriptor Base Address High - RW */ +#define E1000_TDLEN 0x03808 /* TX Descriptor Length - RW */ +#define E1000_TDH 0x03810 /* TX Descriptor Head - RW */ +#define E1000_TDT 0x03818 /* TX Descripotr Tail - RW */ +#define E1000_TIDV 0x03820 /* TX Interrupt Delay Value - RW */ +#define E1000_TXDCTL 0x03828 /* TX Descriptor Control - RW */ +#define E1000_TADV 0x0382C /* TX Interrupt Absolute Delay Val - RW */ +#define E1000_TSPMT 0x03830 /* TCP Segmentation PAD & Min Threshold - RW */ +#define E1000_TARC0 0x03840 /* TX Arbitration Count (0) */ +#define E1000_TDBAL1 0x03900 /* TX Desc Base Address Low (1) - RW */ +#define E1000_TDBAH1 0x03904 /* TX Desc Base Address High (1) - RW */ +#define E1000_TDLEN1 0x03908 /* TX Desc Length (1) - RW */ +#define E1000_TDH1 0x03910 /* TX Desc Head (1) - RW */ +#define E1000_TDT1 0x03918 /* TX Desc Tail (1) - RW */ +#define E1000_TXDCTL1 0x03928 /* TX Descriptor Control (1) - RW */ +#define E1000_TARC1 0x03940 /* TX Arbitration Count (1) */ +#define E1000_CRCERRS 0x04000 /* CRC Error Count - R/clr */ +#define E1000_ALGNERRC 0x04004 /* Alignment Error Count - R/clr */ +#define E1000_SYMERRS 0x04008 /* Symbol Error Count - R/clr */ +#define E1000_RXERRC 0x0400C /* Receive Error Count - R/clr */ +#define E1000_MPC 0x04010 /* Missed Packet Count - R/clr */ +#define E1000_SCC 0x04014 /* Single Collision Count - R/clr */ +#define E1000_ECOL 0x04018 /* Excessive Collision Count - R/clr */ +#define E1000_MCC 0x0401C /* Multiple Collision Count - R/clr */ +#define E1000_LATECOL 0x04020 /* Late Collision Count - R/clr */ +#define E1000_COLC 0x04028 /* Collision Count - R/clr */ +#define E1000_DC 0x04030 /* Defer Count - R/clr */ +#define E1000_TNCRS 0x04034 /* TX-No CRS - R/clr */ +#define E1000_SEC 0x04038 /* Sequence Error Count - R/clr */ +#define E1000_CEXTERR 0x0403C /* Carrier Extension Error Count - R/clr */ +#define E1000_RLEC 0x04040 /* Receive Length Error Count - R/clr */ +#define E1000_XONRXC 0x04048 /* XON RX Count - R/clr */ +#define E1000_XONTXC 0x0404C /* XON TX Count - R/clr */ +#define E1000_XOFFRXC 0x04050 /* XOFF RX Count - R/clr */ +#define E1000_XOFFTXC 0x04054 /* XOFF TX Count - R/clr */ +#define E1000_FCRUC 0x04058 /* Flow Control RX Unsupported Count- R/clr */ +#define E1000_PRC64 0x0405C /* Packets RX (64 bytes) - R/clr */ +#define E1000_PRC127 0x04060 /* Packets RX (65-127 bytes) - R/clr */ +#define E1000_PRC255 0x04064 /* Packets RX (128-255 bytes) - R/clr */ +#define E1000_PRC511 0x04068 /* Packets RX (255-511 bytes) - R/clr */ +#define E1000_PRC1023 0x0406C /* Packets RX (512-1023 bytes) - R/clr */ +#define E1000_PRC1522 0x04070 /* Packets RX (1024-1522 bytes) - R/clr */ +#define E1000_GPRC 0x04074 /* Good Packets RX Count - R/clr */ +#define E1000_BPRC 0x04078 /* Broadcast Packets RX Count - R/clr */ +#define E1000_MPRC 0x0407C /* Multicast Packets RX Count - R/clr */ +#define E1000_GPTC 0x04080 /* Good Packets TX Count - R/clr */ +#define E1000_GORCL 0x04088 /* Good Octets RX Count Low - R/clr */ +#define E1000_GORCH 0x0408C /* Good Octets RX Count High - R/clr */ +#define E1000_GOTCL 0x04090 /* Good Octets TX Count Low - R/clr */ +#define E1000_GOTCH 0x04094 /* Good Octets TX Count High - R/clr */ +#define E1000_RNBC 0x040A0 /* RX No Buffers Count - R/clr */ +#define E1000_RUC 0x040A4 /* RX Undersize Count - R/clr */ +#define E1000_RFC 0x040A8 /* RX Fragment Count - R/clr */ +#define E1000_ROC 0x040AC /* RX Oversize Count - R/clr */ +#define E1000_RJC 0x040B0 /* RX Jabber Count - R/clr */ +#define E1000_MGTPRC 0x040B4 /* Management Packets RX Count - R/clr */ +#define E1000_MGTPDC 0x040B8 /* Management Packets Dropped Count - R/clr */ +#define E1000_MGTPTC 0x040BC /* Management Packets TX Count - R/clr */ +#define E1000_TORL 0x040C0 /* Total Octets RX Low - R/clr */ +#define E1000_TORH 0x040C4 /* Total Octets RX High - R/clr */ +#define E1000_TOTL 0x040C8 /* Total Octets TX Low - R/clr */ +#define E1000_TOTH 0x040CC /* Total Octets TX High - R/clr */ +#define E1000_TPR 0x040D0 /* Total Packets RX - R/clr */ +#define E1000_TPT 0x040D4 /* Total Packets TX - R/clr */ +#define E1000_PTC64 0x040D8 /* Packets TX (64 bytes) - R/clr */ +#define E1000_PTC127 0x040DC /* Packets TX (65-127 bytes) - R/clr */ +#define E1000_PTC255 0x040E0 /* Packets TX (128-255 bytes) - R/clr */ +#define E1000_PTC511 0x040E4 /* Packets TX (256-511 bytes) - R/clr */ +#define E1000_PTC1023 0x040E8 /* Packets TX (512-1023 bytes) - R/clr */ +#define E1000_PTC1522 0x040EC /* Packets TX (1024-1522 Bytes) - R/clr */ +#define E1000_MPTC 0x040F0 /* Multicast Packets TX Count - R/clr */ +#define E1000_BPTC 0x040F4 /* Broadcast Packets TX Count - R/clr */ +#define E1000_TSCTC 0x040F8 /* TCP Segmentation Context TX - R/clr */ +#define E1000_TSCTFC 0x040FC /* TCP Segmentation Context TX Fail - R/clr */ +#define E1000_IAC 0x04100 /* Interrupt Assertion Count */ +#define E1000_ICRXPTC 0x04104 /* Interrupt Cause Rx Packet Timer Expire Count */ +#define E1000_ICRXATC 0x04108 /* Interrupt Cause Rx Absolute Timer Expire Count */ +#define E1000_ICTXPTC 0x0410C /* Interrupt Cause Tx Packet Timer Expire Count */ +#define E1000_ICTXATC 0x04110 /* Interrupt Cause Tx Absolute Timer Expire Count */ +#define E1000_ICTXQEC 0x04118 /* Interrupt Cause Tx Queue Empty Count */ +#define E1000_ICTXQMTC 0x0411C /* Interrupt Cause Tx Queue Minimum Threshold Count */ +#define E1000_ICRXDMTC 0x04120 /* Interrupt Cause Rx Descriptor Minimum Threshold Count */ +#define E1000_ICRXOC 0x04124 /* Interrupt Cause Receiver Overrun Count */ +#define E1000_RXCSUM 0x05000 /* RX Checksum Control - RW */ +#define E1000_RFCTL 0x05008 /* Receive Filter Control*/ +#define E1000_MTA 0x05200 /* Multicast Table Array - RW Array */ +#define E1000_RA 0x05400 /* Receive Address - RW Array */ +#define E1000_VFTA 0x05600 /* VLAN Filter Table Array - RW Array */ +#define E1000_WUC 0x05800 /* Wakeup Control - RW */ +#define E1000_WUFC 0x05808 /* Wakeup Filter Control - RW */ +#define E1000_WUS 0x05810 /* Wakeup Status - RO */ +#define E1000_MANC 0x05820 /* Management Control - RW */ +#define E1000_IPAV 0x05838 /* IP Address Valid - RW */ +#define E1000_IP4AT 0x05840 /* IPv4 Address Table - RW Array */ +#define E1000_IP6AT 0x05880 /* IPv6 Address Table - RW Array */ +#define E1000_WUPL 0x05900 /* Wakeup Packet Length - RW */ +#define E1000_WUPM 0x05A00 /* Wakeup Packet Memory - RO A */ +#define E1000_FFLT 0x05F00 /* Flexible Filter Length Table - RW Array */ +#define E1000_HOST_IF 0x08800 /* Host Interface */ +#define E1000_FFMT 0x09000 /* Flexible Filter Mask Table - RW Array */ +#define E1000_FFVT 0x09800 /* Flexible Filter Value Table - RW Array */ + +#define E1000_KUMCTRLSTA 0x00034 /* MAC-PHY interface - RW */ +#define E1000_MDPHYA 0x0003C /* PHY address - RW */ +#define E1000_MANC2H 0x05860 /* Managment Control To Host - RW */ +#define E1000_SW_FW_SYNC 0x05B5C /* Software-Firmware Synchronization - RW */ + +#define E1000_GCR 0x05B00 /* PCI-Ex Control */ +#define E1000_GSCL_1 0x05B10 /* PCI-Ex Statistic Control #1 */ +#define E1000_GSCL_2 0x05B14 /* PCI-Ex Statistic Control #2 */ +#define E1000_GSCL_3 0x05B18 /* PCI-Ex Statistic Control #3 */ +#define E1000_GSCL_4 0x05B1C /* PCI-Ex Statistic Control #4 */ +#define E1000_FACTPS 0x05B30 /* Function Active and Power State to MNG */ +#define E1000_SWSM 0x05B50 /* SW Semaphore */ +#define E1000_FWSM 0x05B54 /* FW Semaphore */ +#define E1000_FFLT_DBG 0x05F04 /* Debug Register */ +#define E1000_HICR 0x08F00 /* Host Inteface Control */ + +/* RSS registers */ +#define E1000_CPUVEC 0x02C10 /* CPU Vector Register - RW */ +#define E1000_MRQC 0x05818 /* Multiple Receive Control - RW */ +#define E1000_RETA 0x05C00 /* Redirection Table - RW Array */ +#define E1000_RSSRK 0x05C80 /* RSS Random Key - RW Array */ +#define E1000_RSSIM 0x05864 /* RSS Interrupt Mask */ +#define E1000_RSSIR 0x05868 /* RSS Interrupt Request */ +/* Register Set (82542) + * + * Some of the 82542 registers are located at different offsets than they are + * in more current versions of the 8254x. Despite the difference in location, + * the registers function in the same manner. + */ +#define E1000_82542_CTRL E1000_CTRL +#define E1000_82542_CTRL_DUP E1000_CTRL_DUP +#define E1000_82542_STATUS E1000_STATUS +#define E1000_82542_EECD E1000_EECD +#define E1000_82542_EERD E1000_EERD +#define E1000_82542_CTRL_EXT E1000_CTRL_EXT +#define E1000_82542_FLA E1000_FLA +#define E1000_82542_MDIC E1000_MDIC +#define E1000_82542_SCTL E1000_SCTL +#define E1000_82542_FEXTNVM E1000_FEXTNVM +#define E1000_82542_FCAL E1000_FCAL +#define E1000_82542_FCAH E1000_FCAH +#define E1000_82542_FCT E1000_FCT +#define E1000_82542_VET E1000_VET +#define E1000_82542_RA 0x00040 +#define E1000_82542_ICR E1000_ICR +#define E1000_82542_ITR E1000_ITR +#define E1000_82542_ICS E1000_ICS